markem-imaje RMCIJ1 RFID Integrated Module Owner’s Manual

markem-imaje RMCIJ1 RFID Integrated Module

Specifications

• Product Name : Markem-Imaje RFID module RMCIJ1
• Manufacturer: Markem-Imaje Industries
• Address: 9 rue Gaspard Monge, 26500 Bourg-les-Valence, FRANCE
• Telephone: +33 (0)4 75 75 55 00
• Website: www.markem-imaje.com
• FCC Certification: Part 15 of the FCC Rules, FCC ID: 2AAW8-RMCIJ1
• ISED Certification: Compliant with ISED RSS-210 and RSS-Gen rules, IC: 11372A-RMCIJ1

Markem-Imaje RFID module RMCIJ1

RMCIJ1 is an RFID module integrated in Markem-Imaje CIJ printers which ensures the authenticity and reliability of ink and additive cartridges An RFID tag is fitted to each ink cartridge and contains the set-up information of the cartridge as required by the printer.
Thanks to this RFID module, the printer reads the RFID tag during the calibration process and ‘pairs’ with the cartridge.

Technical features

• RFID radio frequency: 13.56MHz
• Electrical Rating: 5V, 25 mW
• Operating temperature: 0°C to +50°C (+32°F to +122°F)
• Storage temperature: -10°C to +55°C (14°F to 131°F)
• RFID module weight: 50 g
• Integrated Antenna dimensions: 25 mm x 50 mm
  Not sold separately, only integrated in Markem-Imaje CIJ printers.

Regulatory Statements

Radio

• An RFID tag is fitted to each ink cartridge and contains the set-up information of the cartridge as required by the printer.
• The printer reads the RFID tag during the calibration process and ‘pairs’ with the cartridge.
• The RFID radio frequency is 13.56MHz with a maximum power limit of 25mW from the antenna.
• The use of micro-power short-range radio transmission equipment shall comply with the relevant provisions of the China National Radio Administration.

Label

FCC

FCC certification

• The RMCIJ1 module complies with part 15 of the FCC Rules. The FCC ID is 2AAW8-RMCIJ1
• The module label includes the corresponding FCC ID.

The operation is subject to the following two conditions:

• This device may not cause harmful interference
• This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Label requirements
If the identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This label must contain the FCC ID that matches the one on the module.

Documentation requirements
The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Integration requirements

• The co-location of this module with other transmitters that operate simultaneously are required to be evaluated using the multi-transmitter procedures.
• The host integrator must follow the integration instructions provided in this document and ensure that the composite-system end product complies with the requirements by a technical assessment or evaluation of the rules and KDB Publication 996369.
• The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation of the rules, including the transmitter operation and should refer to the guidance in KDB 996369.

The radio module must be labelled as follows:
FCC ID: 2AAW8-RMCIJ1

Moreover, the host equipment must be labelled as follows:

• Contains FCC ID: 2AAW8-RMCIJ1,
• Contains IC: 1 1372A-RMCIJ1

Warning: This module is used exclusively by Markem Imaje. This product and the antennas must be professionally installed

ISED certification

The STM32WB5MMG module has been tested and found compliant with the ISED RSS-210 and RSS-Gen rules. The IC is 11372A-RMCIJ1 .
This module contains license-exempt transmitter(s) that comply with Innovation, Science and Economic Development

Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

• This module may not cause interference
• This module must accept any interference, including interference that may cause undesired operation of the module.

The radio module must be labelled as follows:

• IC: 11372A-RMCIJ1

Moreover, the host equipment must be labelled as follows:

• Contains FCC ID: 2AAW8-RMCIJ1,
• Contains IC: 11372A-RMCIJ1

Warning: This module is used exclusively by Markem Imaje. This product and the antennas must be professionally installed

• RFID: Radio Frequency Identification
• FCC: Federal Communications Commission
• USA ISED: Innovation, Science and Economic Dvlpt- Canada

Frequently Asked Questions

• Q: Can I install the RMCIJ1 module myself?
  • A: No, professional installation is required for this product to ensure proper functionality and compliance with regulations.
• Q: What happens if I modify the module without approval?
  • A: Unauthorized modifications could void your authority to operate the equipment. Always follow approved guidelines.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>