ENGWE P26 Urban E Bike For Commuter Instruction Manual

P26 Urban E Bike For Commuter
Instruction Manual

P26
CAUTION READ THIS MANUAL BEFORE USING YOUR EQUIPMENT

General Information

Bike Components

Attachment: technical parameters

Main Parameters of the
Whole Vehicle| Maximum Speed| 28mph(45km/h)| 15.5mph(25km/h)
Maximum Gradient| 7°| 7°
Rear Derailleur| 7-Speed| 7-Speed
Mileage Range| 28 miles(45km)| 40 miles(65km)
Working Temperature| 23°F-95°F(-5 -35)| 23°F-95°F(-5 -35 )
Battery Parameters| Rated Voltage| 4W| 36V
Battery Capacity| 13.6AH| 17AH
Service Life| 500 Times| 500 Times
Motor Parameters| Motor Power| 500W| 250W
Motor Type| Brushless Gear Motor| Brushless Gear Motor
Maximum Torque| 55Nm| 45Nm
Charger Parameters| Input Voltage| 100-240V| 100-240V
Output Voltage| 54V| 42V
Output Current| 2A| 2A

Unwrap your ENGWE e-bike

1. Take out the bike, the seatpost, and the tool box.
2. Remove (and recycle) all wrapping material.
3. Save the bike box and tool box for future use.

Tool box checklist

Take out the front wheel

1. Take out the front wheel.
2. Remove (and recycle) the plastic covers from both sides of the wheel hub.

Rotate the stem to the front

1. Hold the head tube in one hand.
2. Use the other hand to rotate the stem to the front-facing direction.

Take off the front attachment of the stem

1. Use a 4mm hex key to unscrew the 4 handlebar clamp bolts by turning counterclockwise.
   Be careful not to lose the bolt washers.

Install the handlebar

1. Place the handlebar at an appropriate position, make sure the “cross symbol” is located at the center.
2. Use a 4mm hex key to install the 4 bolts by turning clockwise. The sequence is shown in the picture above. Please do not fully tighten them yet.
3. 0nce the bolts and the handlebar are in the right place, tighten the bolts fully with appropriate force.

Install the front light

1. Rotate the front light to the upright position.
2. Use a wrench to secure the front of the mounting bolt of the lamp.

Install the front Whee

This step s extremely important, so please read carefully.

1. Clamp the front wheel with the front fork and lock the front wheel screw with a wrench.

Install the pedals

1. The pedals are marked with “R” (Right) and “L” (Left).
   This refers to the two sides of the e-bike. The R pedal goes to the side of the carbon belt, and the L pedal goes to the other side.

2. Manually install the left pedal by turning counterclockwise. Tighten the pedal securely with a 1 Smm wrench.

3. Manually install the right pedal by turning clockwise. Tighten the pedal securely with a 1 Smm wrench.

Instrument instructions

1. Product name and model
   Intelligent LCD display fore-bike; model: YL80C.

2. Specifications
   • 36V /48V power supply
   • Rated working current I 5mA
   • Maximum working current 30mA
   • Leakage current at power-off <I uA
   • Working current at the supply controller end 50mA
   • Working temperature -20∼60″C
   • Storage temperature -30∼70″C

3. Appearance and dimensions

4. Function overview and functional area layout
   4.1 Function overview
   Display YL80C provides a variety of functions to meet your riding needs, including:
   • Battery level indicator
   • Motor power ndicator
   • Assist level adjustment and indication
   • Speed indicator (including real-time speed, maximum speed and average speed)
   • Distance indicator (including trip distance and ODO)
   • Push assistance control and indication
   • Headlight control and indication
   • Error code indicator
   • USB connection indicator (reserved)
   • Heart rate indicator (reserved)
   • Bluetooth connection indicator (reserved)
   • Custom parameter setting (e.g., wheel diameter, speed limit, battery level, assist level, power-on password. controller current limit, etc.)
   • Reset function
   4.2 Functional area layout 4.3 Button definitions
   There are five buttons on the operating unit of display YL80C, i.e., the on/off button plus button · minus button , headlight button and switching button .

5. General operation
   5.1 Power on/off
   By pressing and holding the button , the display will start to work and the working power supply of the controller will be turned on. ln the power-on state, by pressing the button , your e-bike will be powered off. In the power- off state, the display will no longer use the battery power, and its leakage current will be less than I uA.
   • If your e-bike is not used for more than 10 minutes, the display will be automatically powered off.
   5.2 Display interface
   After the display is turned on, the display will show the real-time speed (km/h) and the trip distance (km) by default.
   By pressing the button the information displayed will be switched between the trip distance (km), ODO (km), maximum speed (km/h), average speed (km/h) and riding power. 5.3 Push assistance
   By pressing and holding the button. , the electric push assistance mode will be enabled. Your e-bike will run at the output and return to the state before push assistance.
   constant speed of 6km/h. The display will show . By releasing the button , your e-bike will immediately stop power • The push assistance function can only be used when you are pushing your e-bike. Please do not use it during riding.
   5.4 Headlight on/off
   By pressing the button , the controller will tum on the headlights and the display back light will tum dark; by pressing the button again, the controller will turn off the headlights and the display backlight will resumes the luminance. 5.5 Assist level selection
   By pressing the button , thee-bike assist level will be switched to change the motor output power. 5.6 Battery level indicator
   The battery level indicator consists of five segments. When the battery is fully charged, the five segments will be all on In case of undervoltage, the outline of the battery indicator will flash, which means the battery has to be charged
   immediately. 5.7 Motor power indicator
   The display can indicate the output power of the motor, as shown in the figure below. 5.8 Error code indicator
   When a fault occurs in the electronic control system of your e-bike, the display will automatically indicate the error code. Detailed definitions of error codes are shown in Schedule I.
   • When an error code appears on the display interface, please conduct troubleshooting in time. Otherwise, your e-bike will · not work normally.

6. General setting
   • All parameters can only be set when your e-bike stops.
   The steps for general setting are as follows:
   In the power-on state, when the display shows the speed of 0,
   (1) Press and hold the buttons and at the same time for more than 2 seconds to enter the selection interface of general setting options;
   (2) Press the button to switch the selection interface of general setting options, and press the button to enter the parameter modification interface;
   (3) Press the button for parameter selection;
   (4) Press the button to save the parameter and return to the selection interface of general setting options;
   (5) Press and hold the button to save the parameter and exit the selection interface of general setting options.
   The following selection interfaces of general setting options are available:
   6.1 Trip distance reset
   tC refers to the trip distance reset item. tC-n means not to reset the trip distance, and tC-y means to reset the trip
   distance.
   Press the button to enter the parameter modification interface. Press the button for parameter selection.
   Press the button to save the parameter and return to the selection interface of general setting options. 6.2 Back.light luminance setting
   bL refers to the backlight luminance setting option. Parameters bL-1, bL-2 and bL-3 are available, which represent the backlight luminance, 1 for the minimum luminance, 2 for the standard luminance and 3 for the maximum  luminance.
   Press the button to enter the parameter modification interface. Press the button for parameter selection.
   Press the button to save the parameter and return to the selection interface of general setting options. 6.3 Metric/imperial system setting
   Un refers to the metric/imperial system setting option. U- l represents the imperial system, and U-2 represents the metric system.
   Press the button to enter the parameter modification interface. Press the button for parameter selection.
   Press the button to save the parameter and return to the selection interface of general setting options.

7. General parameter setting
   The steps for general parameter setting are as follows:
   ln the power-on state, when the display shows the speed of 0,
   (I) Press and hold the buttons at the same time for more than 2 seconds to enter the selection interface of general setting options;
   (2) Press and hold the buttons and at the same time for more than 2 seconds to enter the selection interface of general parameter setting options;
   (3) Press the button to switch the function, and press the button to enter the parameter modification interface;
   (4) Press the button for parameter selection;
   (5) Press the button to save the parameter and enter the next selection interface of general parameter setting options;
   (6) Press and hold the button to save the parameter and exit the selection interface of general parameter setting options.
   7.1 Wheel diameter setting
   Ld refers to the wheel diameter setting option. Available parameters include: 8-26, 700C, 28-30 inches.
   Press the button to enter the parameter modification interface. Press the button to select the wheel diameter corresponding to your e-bike (to ensure the accuracy of the speed and distance indication of the display). Press the
   button to save the parameter and enter the next selection interface of general parameter setting options. 7.2 Speed limit setting
   LS refers to the speed limit setting option. By modifying this value, you can set the maximum riding speed of your e-bike, The selectable range of the maximum speed setting value is 12km/h-40km/h.
   Press the button to enter the parameter modification interface. Press the button to select the maximum riding speed. Press the button to save the parameter and enter the next selection interface of general parameter setting options.

8. Custom setting
   In order to meet the individual requirements of customers, custom setting options are available, including: battery level setting of the display, assistance parameter setting, current limit setting, assistance sensor setting, speed  sensor setting, handlebar function setting, system setting and power-on password setting, totally eight setting options. Not all protocols support the custom setting options of display YLSOC. Some protocols only support part of the  setting options. Press the button to switch the level. Press the button to confirm the level mode and enter the 8.2.2 assistance ratio setting option, or press and hold the button to confirm the setting and return to the selection  interface of custom setting options. 8.1 Assistance sensor setting (option)
   8.1. I Assistance sensor sensitivity setting
   SCN refers to the assistance sensor sensitivity setting option. The setting range is 2-9, where 2 means the maximum sensitivity and 9 means the minimum sensitivity.
   Press the button to select the assistance sensor sensitivity. Press the button to confirm the parameter and enter the 8.4.3 steel magnet number setting option for assistance magnetic disk, or press and hold the button to  confirm the parameter and return to the selection interface of custom setting options. 8.2 Power-on password setting (option)
   8.2.1 Power-on password enable setting
   By inputting the password, you can enter the password enable setting option. PSd-Y means that a power-on password is required, and PSd-N means that no power-on passwords are required.
   Press the button for parameter selection.
   If you select PSd-N, press the button to confirm the parameter and return to the selection interface of custom setting options. If you select PSd-Y, press the button to enter the 8.8.2 power-on password modification setting  option, or press and hold the button to confirm the parameter and return to the selection interface of custom setting options. 8.2.2 Power-on password modification setting
   P3 refers to the power-on password modification setting option. Press the button for cursor movement and the button for parameter selection. After the modification, press and hold the button to save and confirm the parameter and return to the selection interface of custom setting options. If the display is rebooted, it will show PI, 0000, and it will not work normally until you enter the correct password.

9. Restore default settings
   dEF refers to the setting option of restoring default parameters. dEF-Y means that the default settings need to be restored, and dEF-N means that there is no need to restore the default settings. In the normal display interface, press  and hold the buttons and at the same time for more than 2 seconds to enter the restore default settings interface. Switch the parameter by pressing the button . If you choose Y, press and press the button to confirm the parameter. The display will indicate dEF-0 and automatically start to restore the default settings. After the restoration is completed, it will automatically exit and return to the normal display interface.

10. Quality commitments and warranty scope
    10.1 Warranty information:
    • For the faults caused by the quality of the product under normal use, the Company will be responsible for providing limited warranty during the warranty period.
    • The warranty period of the product is within 12 months from delivery.
    10.2 Non-warranty scope
    • The enclosure is opened
    • The connector is damaged
    • The enclosure is scratched or damaged after delivery
    • The outgoing line of the display is scratched or broken
    • Faults or damage caused by force majeure (such as fires, earthquakes, etc.) or natural disasters (such as lightning strikes, etc.)
    • The warranty period has expired

11. Outgoing line connection diagram
    11.1Wiring sequence of standard connector Table 8-1 Wiring Sequence of Standard Connector

• The outgoing lines of some products adopt waterproof connectors, and users cannot see the outgoing line color inside the wire harnesses.

12. Considerations
    Please use safely, and do not plug or unplug the display when it is powered on.
    + Please avoid bumping as far as possible.
    + Please do not alter the background parameter settings of the display at will, otherwise normal riding cannot be guaranteed.
    + If the display fails to work normally, it should be repaired as soon as possible.
    + Due to product upgrades of the Company, part of the displayed contents or functions of the product you bought may be different from the manual, depending on the actual model.
    Schedule I Error Code DefinitionsFault codes for protocols YL-0 I and YL-02.

    Fault code| Fault description| | Fault code| Fault description
    E001| Controller failure| E004| Handlebar failure
    E002| Communication failure| E005| Brake lever failure
    £3| Hall element failure| £6| Default phase of motor
    Fault codes for protocols YL-05.. ICDS and YL-J:
    Fault code| Fault description| Fault code| Fault description
    £21| Anconal current| I £024| Hall element failure
    E022| Handlebar failure| I £025| Brake failure
    E023| Default phase of motor| I £030| Communication failure

Schedule 2: Assist Level Ratio Default Values****

Assist level| | | | | | | | |
---|---|---|---|---|---|---|---|---|---
| 1| 2| 3| 4| 5| 6| 7| 8| 9
Assist level selection| | | | | | | | |
0-3/1-3| 50%| 74%| 92%| —| —| —| —| —| —
0-511-5| 50%| 61%| 73%| 85%| 96%| —| —| —| —
0-711-7| 40%| 50%| 60%| 70%| 80%| 90%| 96%| —| —
0-911-9| 25%| 34%| 43%| 52%| 61%| 70%| 79%| 88%| 96%

Tel: 022-86838795
Email: yolin@yolintech.com
Website: www.yolintech.com
Fax: 022-86838795
Address: Plant 52-1, Youku Xinkc Park, East of Jingju Road, Pharmaceuticals and Medical Equipment Industrial Park, Birchen
Economic Development Zone, Beechen District, Tianjin

Battery: Further Information and Maintenance

• How far full charge battery can go? That depends on the loading weight, road condition and battery capacity. But in the same condition, average speeds can continuous longer travel range.

• when storing the battery for a longer time,(during winter time)it is important to place the fully charged battery in a dry place.

• Attention: The battery should be re-charged once every 2-3 month when it is not used.
  WARNING:

• Keep the battery out of reach for children.

• Never try to open the battery.

• only use the ENGWE supplied battery. Do not use a battery from any other different product models.

• 1f the battery is damaged because it has been dropped somewhere or biking accident, there may be a risk of electrolytes leakage. Beware of chemical burns! And mmediately stop using the damaged battery.

• Do not touch the battery without a cloth or gloves and make sure no acid touches your eyes.

• Do not store the battery in temperatures above 95F or below 23°F.

• Do not allow the battery to run down completely before charging. Charge the battery before storing the product. If the battery is completely empty, it may cause the battery to no longer charge.

• charge a new battery for at least 4-6 hours before you use it in your product for the first time. Never charge the battery too long per time. Overheating or undercharging the battery  may shorten battery life and decrease product run time.

IMPORTANT:BATTERY DISPOSAL

• Battery must be recycled or disposed of in an environmentally sound manner.
• Do not dispose of the battery n a fire. The battery may explode or leak.
• Do not dispose of a battery in your regular household trash.

Charging

• How far full charge battery can go? That depends on the loading weight, road condition and battery capacity. But in the same condition, average speeds can continuous longer travel range.

• You can charge the bike directly, or you can remove the battery for charging.

• The RED light indicates it is in charging and GREEN light indicates the battery is fully charged.(Please put off plug from wall)Usually the charging time is 4-6 hours depends on the battery capacity remain.
  WARNING:

• charging time over 10 hours is prohibited please kept it away from high temperature environment and stores it in a cool place.

• Please make sure that the battery charger and charging plug are always kept dray and never get wet.

• The charger should only be cleaned with a dry cloth. Never use a wet cloth. oil or any other liquid.

• Do not connect positive and negative terminals.

• Stop the charging procedure immediately if you notice anything unusual.

• It is strictly forbidden to cut the battery charging and discharging lines.

• It is strictly forbidden to disassemble the battery box or modify the internal structure and protection board of the lithium battery.

• It is strictly forbidden to disassemble the battery box or modify the internal structure and protection board of the lithium battery.

• Only use the ENGWE supplied charger. Do not use a charger from any other different product models.

• After using the battery. please charge it within 12 hours.

If the product has problems with the following forms during the protection period, we will provide customer service as part of the product quality guarantee.

Quality Assurance

Accessories| quality problem| Warranty period| service content
---|---|---|---
Motor| Motor will not be able to use| I year| Free delivery of parts
Accelerator| Natural conditions (such as impact
force cannot be used except damage)| 1 year| Free delivery of parts
Controller| Failure occurs under normal use| 1 year| Free delivery of parts
Charger| Failure occurs under normal use| 1 year| Free delivery of parts
Lithium Battery| Can’t charge discharge under normal use| 1 year| Free delivery of parts

Notes:
If the above issues occur during the protection period, please contact us and send us photos or videos of the defective parts. If we confirm that the fault is caused by the quality of the product itself, we will send you the parts that are needed replaced for free.
Year Limited Hardware Warranty
Your ENGWE Electric bike includes a One Year Limited Hardware Warranty. The Warranty covers product defects in materials and workmanship under normal use. This Warranty is limited to original purchasers. This Warranty starts on  the date of your purchase and lasts for one year (the “Warranty Period”).The Warranty Period is not extended if the Product is repaired or replaced.
Warranty services are provided by the e-bike .lf a hardware defect arises and a valid claim is received within the Warranty Period, at its option and to the extent permitted by law, ENGWE will resend new parts that are equivalent to new  in performance and reliability. This Warranty is not assignable or transferable. The original purchaser may contact us for service request. This Warranty does not cover any damage due to :improper use ;failure to follow the product  instructions or to perform any preventive maintenance; unauthorized repair; external causes such as accidents, abuse, or other actions or events beyond our reasonable control.
Any question about the item, please contact the customer service from where you brought your device.

https://engwe-bikes-eu.com
https://engwe-bikes.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>