ENGWE BIKES 9053851 20 inch Fat Tire Folding Electric Bike User Manual

ENGWE BIKES 9053851 20 inch Fat Tire Folding Electric Bike

Product Information

Specifications

• Brand: ENGWE-BIKES
• Model: 20 inch Fat Tire Folding Electric Bike
• Features: Folding design, Fat tire, Electric-powered
• Speeds: 5-speed switching gears
• Battery: Rechargeable, 5-7 hours for full charge
• Display: LCD meter with switch button

Product Usage Instructions

Safety Instructions

Before operating the e-bike, read the user manual carefully to ensure safe and proper usage. Do not dismantle any components.
Check all parts are tightened before riding. Keep charger and battery dry.

How to Start the Electric Bicycle

1. Ensure the battery is fully charged (indicator light turns green).
2. Insert the battery key into the steel tube base and open the battery lock.
3. Press the switch button on the LCD meter to turn it on.
4. Twist the right-hand throttle to run at full throttle.

Using Shift Paddles Smoothly
If shift paddles are not smooth, adjust rear wheel transmission to be loose and tight. Ensure speed and gear match for smooth shifting.

Troubleshooting Chain Issues
If the chain rubs against the rear wheels or rear derailleur bends, refer to the user manual for specific instructions on adjustments.

Battery Removal
To remove the battery, insert the key into the steel tube base,press the key inwards, rotate to unlock, and pull the battery bracelet to remove it.

FAQ

Q: How long does it take to fully charge the battery?
A: The battery takes approximately 5-7 hours to fully charge.

Q: What should I do if the chain rubs against the rear wheels?
A: Adjust the rear wheel transmission to ensure smooth operation of the chain.

20 inch Fat Tire Folding Electric Bike
Operation and maintenance manual
Before using the e-bike, please read the attached operating instructions.
Carefully read the safety rules.

Safety instruction

1. Thank you for purchasing the E-BIKE. The E-BIKE features the most recent innovation in technology.
2. For Safety reasons, it is most important that you read this USER MANUAL BEFORE you operate the bike. Improper handling can reduce its riding performance and most importantly, pose danger to your safe and healthy.
3. For handling and maintenance of the bicycle, please refer to the E-BIKE User’s Manual which is an integral part of this e-bike user’s manual!
4. Do not at any time dismantle or disassemble any of the above e-bike components!
5. Please check all parts are tighten and locked before riding
6. Please make sure that the charger and battery charging plug are always kept dray and does not get wet at any time.
7. The charger should only be cleaned with a dry cloth. Never use a wet cloth, oil or any other liquid.

Instruction

YL80C LCD smart Meter content display includes:
Speed + power + mileage (editable)

How to start the electric bicycle?

1. Make sure the battery is full charged. When the charges the battery, the indicator light of the charger is red. When the battery is fully charged, the indicator light of the charger is green. (5-7 hours can be fully charged)
2. Then insert the battery key into the steel tube base,and open the battery lock to “ON”, so that the battery can normally supply power to the electric bicycle(Can’t pull out the key, when the electric bicycle is powered on)
3. Finally, there is a switch button on the left hand side of the LCD meter. Press “M” to turn the meter on or off
4. Twist the right-hand throttle to run (full throttle)

How to use shift paddles more smoothly?

If the shift paddles are not smooth (or the chain rubs against the rear wheels), you can adjust the rear wheel transmission to be loose and tight.(Note that the speed and the gear must match to be more smooth to complete the shift paddle)

When the chain of the rear derailleur rubs against the tires how to do? How to deal with the latter’s rear derailleur bending ?

1. Just push the rear derailleur to the outside to make the chain and the tire have a distance of 1-2CM.

2. Disassemble the rear derailleur directly, there is a white metal, you need to move it 1-2cm outside, and then reinstall the rear derailleur
   It is recommended to directly adopt scheme 1, which is simple and effective, and will not affect the use of functions

3. If the silver metal fish hook is bent and deformed, the rear derailleur should become stuck. You can replace the silver metal fish hook or directly hammer it to become straight.

How to remove the battery?
Insert the key into the base of the steel tube, then press the key inwards, and finally rotate to unlock,and finally pull the battery bracelet to remove the battery.

You have to push the key inward, and then turn the key.You have to push the key inward, and then turn the key.

You have to push the key inward, and then turn the key to “on”unlock

How to adjust the brake loose or tight?

Please see the picture, it only needs to be adjusted according to the tension of the brake

Operation Cautions
Be careful of the safety use. Don’t attempt to release the connector when charging the battery.

• Avoid the risk of collision.
• Don’t modify system parameters to avoid parameters disorder.
• Make the display repaired when error code appears.

Battery:further information and maintenance

1. How far full charge battery can go? That depend on the loading weight, road condition and battery capacity. But on the same condition, average speeds can continuous longer travel range.
2. When storing the battery for a longer time period, (e.g. during winter time) it is important to place the full charged battery on a flat surface in a dry place.
3. Attention: The battery should be re-charged once every 2-3 month when it is not used. When not in use, is essential for the life-span of the battery.
4. Warning:
   • Keep the battery out of reach for children.
   • Never try to open the battery.
   • If the battery is damaged because it has been dropped somewhere or because of a biking accident, there might be a risk of electrolytes leakage. Beware of chemical burns! And immediately stop using a damaged battery.
   • Do not touch the battery without a cloth or gloves and make sure no acid touches your eyes.

Charging

1. To charge the battery with the bike, simply place the bike within reach of the power supply and plug it in. Note: The plug hole is located in the left of the frame.
2. The battery can either be charged while on the bike or the battery can be removed and charged at a place of your convenience.
3. The RED light indicates it is in charging and GREEN light indicates the battery is fully charged. (Please put off plug from wall) Usually the charging time sin 4-6hourdepend on the battery capacity remain.
4. Warning: Charging time over 10 hours is prohibited please kept it away from high temperature environment and stores it in a cool place.

Installation Instruction

When open the bike’s carton box, take out folded E-bike and use scissors to cut off the package strings.

Install front wheel:

• a. Take out a protection plate of the front fork and front hub and take out the screw from the fork.

• b. take out the front disc from tool box, install the disc on the hut of front wheel.
  Attention: there is indicate sticker show which surface out side!

• c. Install the fender and lamp, then use tool to tighten.

• d. Take out the bolts and safety washer from the wheel, then make sure front wheel is in line with the rear wheel and proceed to install. (pull the wheel upwards and insert it in the fork drop outs then, insert the safety washers on each side and tighten bolts on each side).

• e. Use tool to tighten

• f. Take out the bolts from the front fork, then install the fender support and use tool to tighten.

Install the handle bar:

• a: open the packing and full down the folding stem
• b: put the stem into the folding stem
• c: let the folding stem veridical and adjusted the handle bar
• d: adjusted the height that best suits your riding position.

Install the seat post:

• a. open the seat post and saddle
• b. flip open the quick release then put the seat post into the frame.
• c. adjust seat post to the height that best suits your riding position and tighten quick release.( Please make sure that the quick release is tightened firmly.)

Warning: Please do not exceed the safety line of seat tube

Install pedals : Check 2 pedals, the one etched “L” should install in left side and “R” in right side. Please use wrench to tighten them.

Adjust angle of brake lever, meter, gear shifter, throttle and louder controller on handle bar, then tightens them with tools.

Read This First: Safety and Compliance with the Law
Congratulations on your purchasing of your new e-bike. Your new e-bike is an excellent piece of personal transportation equipment that will give you good service for many years.
Before you start using your e-bike, we want you to be aware of a few important points. Please read this section carefully.

• Observe Laws Regarding the Use of Battery-Operated Bicycles
  Your e-bike is designed and manufactured to meet safety requirements as a battery-operated bicycle. However, state and local laws governing the use of battery-operated bicycles on public roadways, parks, and other open areas may differ. Please check with your local authority before using your e-bike in public areas.

• Observe Laws Regarding the Use of Bicycles
  Note that all laws regarding the use of bicycles in public areas, such as those mandating the use of helmets and the use of infant seats, will automatically apply for e-bikes. Check with your local authority on what restrictions might apply.

• The Lithium-ion Battery of Your e-Bike
  Your e-bike is equipped with the latest battery technology. The lithium-ion battery is much lighter than lead- or nickel-based batteries that are being used in some older models.

• Your First Ride
  Please be VERY CAREFUL when you are ready to get on your e-bike for the first time because that the e-bike moves significantly faster than a regular bicycle at active power-assisted mode. Take your e-bike to an area with a lot of open space before you start. Do not start pedaling hard as soon as you get on the e-bike (as you normally would so with a regular bicycle), as the e-bike will accelerate under pedal-assist mode and you may be unprepared for the sudden increase in speed.
  However, after a few times, you will enjoy using the pedal-assisted function.
  Your e-bike is driven by a motor embedded in the hub of the rear wheel. The motor is powered by a battery. The amount of power delivered to the motor, and hence the accelerating force on the e-bike, is controlled by you in a way according to the power-assisted mode you choose.
  You can configure the e-bike to operate in the pedal-assist-only-mode or the full power mode (should check against local laws to ensure full power mode is permitted) where you can also use the hand throttle to deliver power to the motor.
  The e-bike is factory-configured to operate in the pedal-assist-only mode.

• Your First Ride
  (Reprinted from the Safety and Compliance with the Law section)
  Please be VERY CAREFUL when you are ready to get on your e-bike for the first
  time because the e-bike moves significantly faster than a regular bicycle at active
  power-assisted mode. Take your e-bike to an area with a lot of open space before
  you start. Do not start pedaling hard as soon as you get on the e-bike (as you
  normally would do with a regular bicycle), as the e-bike will accelerate under
  pedal-assist mode and you may be unprepared for the sudden increase in speed.
  However, after a few times, you will enjoy using the pedal-assisted function.

• Pedal-Assisted
  You must turn on the battery to use the e-bike in pedal-assisted mode.
  In the pedal-assisted mode, power assist is triggered when you pedal forward, and power assist stops when you stop pedaling. In other words, power assist happens as long as you pedal. You don’t need to pedal hard. All you need is to apply a light force to the pedals continuously to maintain the current flow. When you apply one of the brakes, power assist will automatically stop, allowing the e-bike to slow down and stop. Power assist will turn itself off when the e-bike has reached the maximum speed of 18 mph.
  You should use the gear shifter at the handlebar to set the gears appropriately according to road conditions and pedal, as usual, you will find that you need to exert a lot less effort and the e-bike travels faster and at a more steady speed.

• Hand Throttle Control
  In the hand throttle mode, amount of power assist is determined by the throttle switch controlled by your right hand. You control the throttle by twisting it from its resting position, the farther the throttle switch is from its resting position, the more power is delivered to the motor to accelerate the e-bike. When you want to slow down, you simply release the throttle and let it return to its resting position, and simultaneously apply the brakes if necessary.
  You do not need to pedal the e-bike if you use the hand throttle. However, you can pedal while commanding power assist. If you do pedal to help the movement, you conserve energy and the charge in the battery will last longer.

Care and Maintenance for Your New e-Bike
You should, in general, take care of your e-bike the way you would with a regular bicycle by keeping it dry, clean and the moving parts well lubricated. You should also avoid parking your e-bike in exposed areas whenever possible.
You should check the effectiveness of the brakes before each use.

• For your e-Bike, you should also take note of the following:

• Your e-bike is designed for regular country road use for a single person.
  Using your e-bike for extreme maneuvers, such as extreme off-road use, jumping, or carrying the excessive load will damage the e-bike and could cause serious injury.

• Do not use high-pressure water streams to clean your e-bike, as water might seep inside the motor or the wiring compartment and cause rusting of electrical parts or short circuits.

• Avoid parking your e-bike outside when there is rain or snow. At the end of a trip where there was rain or snow, bring the e-bike inside and use a clean, dry towel to eliminate any wetness.

• Be sure you do not lose both keys and remote controls. If you lost one key, you should immediately make a copy as a back-up. If you lost both keys, you will be unable to remove the battery from the e-bike. If you lost both remote controls, you can’t turn on the bike.

• Special Care for the Battery and the Charger

• Use only the supplied charger to charge your battery. Do not use an unauthorized substitute. If your charger is lost or damaged, contact your dealer to order a replacement.

• Do not open or alter the battery or the battery charger.

• Do not place the battery near fire or corrosive substances. Do not immerse in water or other liquids.

• Avoid subjecting the battery from high temperatures, such as directly under the hot sun, for prolonged periods of time.

• Do not connect (short circuit) the two poles of the battery.

• After much use, your battery’s charge holding capacity will decrease. If you find that your battery does not hold sufficient charge even for short trips, you should contact your dealer to order a replacement. Under normal use, the battery will undergo 1000 charging and discharging cycles.

• If the battery will not be used for an extended period of time, charge it fully and recharge it every 3 months. Store it in a cool place.
  ² Your e-bike battery is engineered with precision for high capacity and long useful life. We do not recommend that you use it to power other electrical devices. Improper use of the battery will damage the battery and shorten its useful life and may cause a fire or an explosion.

Trouble Shooting

Can not adjust the speed

Speed is less than 10km/h

| Battery’s voltage is too low

Throttle governing bar is damaged

Poor contact of the

controlling line

Spring failure or being locked

| Fully charge the battery

Replace the throttle governing bar

Replace the spring

Ÿ    e-Bike’s mileage is obviously inadequate after fully charged| Inadequate tire pressure

Failure of charger

The battery cannot be fully charged

Failure of controller

Battery aging or battery damaged

e-Bike has not been well assembled

Too much upgrade road

Strong wind

Bad road

Overweight

Too many braking times

Temperature is too low

| Inflate  tire   with appropriate air pressure

Repair the charger

Examine and repair the controller

Replace the controller

Replace the battery

Re-adjust the e-Bike

Boost    the    e-Bike     by manpower

Warm the battery above 00 Celsius (320 Fahrenheit)

Wheel hub stop running after switching on the power| The connection  of battery is loosen

Poor contact of controlling line

The connection of wheel hub is loose or damaged

The protective board of the battery is broken

| Re-connect the battery

Replace the connection line

Replace the battery’s protective board with a new one

Can e-bike| not| turn| on| the| The remote control is out of power

The Battery is out of power

Battery damaged

| Replace the button cell of the remote control

Fully charge the battery

Replace the battery

As one or more causes of failure might lead to the failure phenomenon, you should find out the true cause(s) and then take the appropriate solution(s) to rectify the problem. In case of doubt, please consult a qualified technician for service, repairs or maintenance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>