Engwe P275 ST 250W 27.5 Ananda Mid Drive Motor City E-Bike User Manual

Engwe P275 ST 250W 27.5 Ananda Mid Drive Motor City E-Bike

Product Information

Specifications

• Display Interface: LCD
• Key Definition: D, T, A, S
• Battery Storage and Disposal
• Charger Technical Data and Precautions

Product Usage Instructions

Display Interface

The product features an LCD display interface that provides clear information and data.

Key Definition

The keys on the product are defined as follows:

• D – Function D
• T – Function T
• A – Function A
• S – Function S

Battery Storage and Disposal

Properly store and dispose of the batteries according to local regulations to ensure environmental safety.

Charger Technical Data and Precautions

Refer to the charger technical data for specifications and follow all precautions provided to ensure safe charging of the product.

FAQ

• Q: How should I dispose of the batteries?
  • A: Please refer to the battery storage and disposal section in the user manual for proper disposal guidelines.
• Q: What do the keys D, T, A, S on the product do?
  • A: Each key corresponds to a specific function. Refer to the key definition section for details on their functions.

Preface

Thank you for choosing the ENGWE series of products. In order to familiarize yourself with the use and ensure a safer ride, please read this manual carefully.

1. Before riding, carefully check if all components are in good condition to ensure your safety. If any problems are found, please contact the seller in a timely manner.
2. Please comply with the traffic regulations in your local area. Slow down in rainy, snowy, and slippery road sections, and increase braking distance when braking to ensure safety.
3. The vehicle can be ridden in rainy and snowy weather, but when the waterline approaches the center of the motor, in order to ensure your safety and prevent damage to the internal circuit of the vehicle, please avoid riding through water.
4. The vehicle battery is a safe battery, but it is prohibited to touch the metal pieces of the battery discharge component with your hands, and you should never touch the battery electrodes and the vehicle circuit with other metal objects to avoid the risk of short circuit.
5. It is prohibited to use the vehicle’s matching battery to power other electrical appliances, as this may cause damage to the battery. Please use the original charger to charge the battery.
6. Do not disassemble or dismantle components by yourself. If replacement is needed, please purchase standard components from the seller.
7. Please avoid washing the vehicle directly with water. If cleaning is necessary, use a cleaning tool to wipe it.
8. Regularly maintain your brakes, tires, and other movable components to ensure the normal operation of your vehicle

Vehicle Basic Information

Ebike Introduction

Vehicle Parameters

Product Applicable Characteristics

This product is a vehicle designed specifically for urban commuting, with strong power and long range. Suitable for riding on urban paved roads, flat gravel roads, and improved small roads with moderate slopes and non-slip tires.A rear shelf has been designed at the tail, which can accommodate objects up to 25 KG. Adopting a pull-out battery box design, the battery can be easily removed by simply turning the key . High brightness headlights make riding safer at night.

Vehicle Assembly Instructions

Vehicle Component Details

Vehicle Packaging Details

Packaging Box

| Complete Vehicle| ****

One Unit

Accessory Box

| ****

One Instruction Manual

Tool Kit

Pedals

Charger

Other Accessories

Tool Kit Details

Bolt Size/Tools/Torque Specifications

Vehicle Assembly and Adjustment

Remove the front wheel

Take off the protective covers on both sides oft he front wheel.

Remove the foam wrapped around the handlebar and then adjust the instrument to its proper position.Align the handlebar and ensure the “cross mark” is at the center.Using a 4mm hex wrench, turn clockwise to install the 4 screws. The installation sequence is shown in the figure below.Once the screws and the handlebar are in the correct position, tighten the screws, applying appropriate force.

Remove the foam wrapped around the front fender, as shown in the figure below. Align the front fender lug with the front fork installation hole and tighten the screw using a 4mm hex wrench. Align the front fender bracket with the installation hole, as shown in the figure below, and tighten the screw with a 4mm hex wrench

Place the nut and washer on the front wheel as shown in the figure below, following the sequence.

Clamp the front wheel with the front fork and lock the front wheel screw with a 15mm open-end wrench

Remove the foam wrapped around the rear fender, as shown in the figure below. Align the rear fender bracket with the installation hole and tighten the screw using an 4 hex wrench.

Take the cargo rack out of the cardboard box, remove the wrapped foam, align it with the installation hole as shown in the figure below, and tighten the screw with an 4 hexwrench.

When installing the pedals, note the markings “R” (right) and “L” (left). The pedal marked with “R” should be installed on the right side of the bike and tightened clockwise with a 15mm open-end wrench;The pedal marked with” L” should be installed on the left side of the bike and tightened counterclockwise with a 15mm open-end wrench.

SaddleAdjustment:

• The seat tube is inserted into the middle tube of the frame, and the screw on the tube clamp is locked with a 4mm wrench.
• After the screw is locked, press the adjustment lever under the seat cushion by hand to adjusttheseatchair height.

Tire Pressure

Please ensure that the tires have sufficient pressure. Insufficient pressure can cause damage to the rims and reduce riding mileage. Please check your tires every 30 days. If the pressure is insufficient, use an inflation device to replenish the standard MPa pressure for your tires. The inflation method is shown in the figure:

Pre-ride Instructions

Riding Techniques

• When the vehicle instrument is in gear 0, the motor is in a no-output state, and the vehicle can be ridden like a normal bicycle.
• When the instrument is in gears 1-5, it represents different speed levels, with gear 1 being the slowest and gears being the fastest.
• Lower gears will make your battery last longer and make your ride safer.
• More power is needed to restore the original speed after emergency braking.
• Use the mechanical transmission to maintain the optimal pedalling frequency with the motor speed, making the riding experience more effortless.
• When shifting gears with the mechanical transmission, lightly step on the pedal to reduce wear on the transmission system.
• When riding in the rain, please maintain a low speed, which will provide greater friction for the tires.
• More weight will accelerate battery consumption.
• Do not start the bicycle by placing one foot on the pedal and crossing the other leg over the seat cushion, as this may cause the vehicle to suddenly accelerate. The correct way to start is to sit on the seat, hold the handlebars with both hands, and then start the vehicle.

Pre-ride Preparation

Regardless of your level of experience, you should carefully read the “User Manual” and perform a safety check on the vehicle. In addition, please make sure you are familiar with the following vehicle-related information.
Before riding, please check the following information about the vehicle:

• Whether key parts such as the front wheel, rear wheel, saddle, and handlebars are loose. if they are loose, they must be tightened before riding.
• Whether the brakes and handles are functioning properly.
• Whether the tire pressure is normal.
• Whether the battery is fully charged.
• When riding at night, check if the front and rear lights of the vehicle are working properly.
• Whether the display components of the instrument are displaying correctly.
• Please wear a cycling helmet and protective gear in accordance with local laws and regulations.

instrument Panel Instructions

Display Function

Display Interface

Key Definition

• Sleep/wake button:
• Display function switch key: “i”;
• Adjustment key:

Power on/off

Press and hold” ” for 2 seconds in the dormant state of the instrument, the instrument will light up and the vehicle will start;
Press and hold the “ ” button for 2 seconds while the vehicle is turned on, and the instrument panel will turn off and the vehicle will shut down.

Gear adjustment display

Short press the key to switch the power assist gear, there are five modes in total: OFF is 0th gear/ECO is 1st gear/TOUR is 2nd gear/SPORT is 3rd gear/SHIFT is 4th gear/BOOST is 5th gear, larger gears can provide more power. When the instrument is turned on, the default gear is OFF, and when OFF is displayed, the vehicle has no power assist at this time. The assist gear selection interface is as shown in the figure below

Basic information switching

In the basic interface, short press the “i” button to switch the subtotal mileage, riding time, average speed, maximum speed, and total mileage display information, Cyclic display: subtotal mileage (TRIP)➔riding time (TRIP TIME)➔total mileage (ODO)➔riding average speed (AVG)➔riding maximum speed (MAX)➔riding motor power (M PWR)➔riding Pedal power (H PWR) ➔ cycling power consumption (CONS) ➔ remaining mileage (RANGE). The mode-switching interface is as shown in the figure

Headlights on/off

• Press and hold the.,…_ key for 2 seconds, the headlights will be turned on, and the instrument headlight indicator icon will light up;
• Press and hold the.,…_ key again for 2 seconds, the headlights are turned off, and the headlight indicator icon goes out. As shown below:

Power-assisted push mode

Press and hold the button on the meter to enter the power-assisted push mode, and the gear position will be displayed. Release the key to exit the power- assisted push mode. The switching interface of the boost promotion mode is as shown in the figure below:

Power display

When the battery level is 5 bars, the battery is fully charged or nearly full; is 0%, the battery needs to be charged immediately; as shown below:

Display Fault Code Description

• Pay attention to safety during use, and do not plug or unplug the meter when it is powered on.
• Avoid bumping the instrument as much as possible.
• Regarding the background parameter setting of the meter, please do not change it arbitrarily, otherwise, norm I riding can not be guaranteed.
• When the instrument cannot be used normally, it should be repaired as soon as possible, and do not disassemble the instrument without permission.

Battery and Charger

Battery Technical Data and Precautions

For transportation safety, the battery is guaranteed to have a 30-40% charge when it leaves the factory. This charge will decrease with the length of transportation time. If you receive the goods, please charge the battery in time.

Your bicycle is powered by a lithium-ion (Li-Ion) battery. Please always follow the following instructions when operating, charging, and using it:

• The vehicle battery is only for use with this vehicle. It is strictly prohibited to connect the battery to other electronic devices, as this may risk damaging the battery.
• Do not modify, open, or disassemble the battery pack. Modifying or disassembling the battery may cause short circuits, fires, or malfunctions.
• The battery is heavy, please handle it with care to avoid dropping it.
• Do not let any sharp or metal objects come into contact with the battery electrodes and charging ports, as there is a risk of short circuits and fires.
• Do not letthe battery overheat and avoid excessive exposure.
• Do not expose the battery to open flames or high temperatures from radiators.
• Do not immerse the battery in water.
• Before performing tasks such as installation, maintenance, cleaning, or repairs, turn off the power and unplug the charger or battery plug. When the bicycle is turned on, touching the contact points may cause electric shock or injury.

Battery Usage Instructions

Before assembling the battery, please make sure that there are no foreign objects in the electrode area of the vehicle. If there are any, they must be cleaned off, otherwise it will cause the risk of battery short circuit and damage.Steps matched with corresponding pictures.

• Raise the seat height to the highest;
• Align the battery with the installation position and insert it directly to the bottom, insert the key into the keyhole, turn the key clockwise, the battery can be locked.

How to remove the battery

• Raise the seat height to the highest;
• Lift the rubber plug, insert the key into the keyhole, press and turn the key in counterclockwise direction, then pull out the key and hold the battery and then pull out the key, then hold the battery cover with your hands and lift the battery upto remove the battery

How to Charge The Battery

The charging time for the battery is 6-8 hours. During charging, both the charger and the battery should be in a good environment. Charging in direct sunlight, rain, or damp conditions is strictly prohibited as it may cause damage to the charger, battery, and the risk of electric shock. It is also prohibited to keep the charger connected to the battery for a longtime, as this may reduce the lifespan of both the battery and the charger.

• First, connect the DC end of the charger cable to the battery charging port.
• When inserting the AC end of the charger into the AC power socket, at this time the charger indicator light is red, charging begins atthis time;
• When the charger indicator light turns green, the battery is fully charged. Unplug the charger from both the AC and DC ends in sequence to complete the charging.

Battery Storage and Disposal

• Storage: If the bicycle is not used for a long time, please remove the battery and store it in a dry, well-ventilated place, and ensure that the storage temperature is between 25-35°C (77-95°F). Also, make sure to charge the battery at least once every three months to keep the battery level at least 3 bars {40-50%), which can effectively extend the battery life.
• Disposal: When the battery is no longer usable, do not dispose of it in your household waste! All batteries and chargers must be disposed of in an environmentally friendly manner according to the battery disposal regulations of your country or region.

Charger Technical Data and Precautions

The following regulations should be followed when using the charger:

• The charger should be placed on a level and non-heated surface.
• Charge the battery in a dry, well-ventilated place, and ensure that the charger is not covered during the charging process.
• When charging the battery, connect the charger to the battery charging port first, and then connect it to the socket.
• Avoid bumping or impacting the charger, as it may damage the charger.
• Avoid leaving the charger plugged into the battery for a long time. If the battery is fully charged, unplug the charger in a timely manner, as it may affect the battery’s lifespan

Common Faults and Maintenance

Warranty Service

Warranty Terms

• The warranty only applies to the original owner of the electric bike purchased through Engwe online or physical stores.
• The warranty period starts when the customer receives the electric bike and terminates immediately upon the expiration, sale, or transfer to another person. Any subsequent owner or transferee is not eligible for the limited warranty.
• For non-human-induced damages during the warranty period, we will provide free replacement parts. After the warranty period, the customer is responsible for the cost of rep la cement parts and shipping

Warranty Coverage

The following conditions are not eligible for warranty:

1. Malfunctions caused by the customer’s failure to use, maintain, and adjust according to the user manual.

2. Malfunctions caused by the customer’s self-disassembly, repair, modification, or failure to comply with the usage rules.

3. Malfunctions caused by improper use or storage by the customer or accidents.

4. Expenses incurred from repairs at other repair shops without our consent.

5. Slight scratches or damages to the outer packaging box of accessories due to logistics issues are not covered by the warranty.

6. Please contact us and obtain written approval before returning any items.
   Products returned without acceptance will not be refunded.

7. The warranty does not cover any rm al wear and tear of components.

8. Consumable parts (such as tires, saddles, plastic parts, brakes, brake rotors, brake pads, brake cables, surface scratches, etc.) a re not covered by the warranty. Please kindly note: Used ebikes, and modified ebikes are not covered by the warranty.

How to Apply for Warranty

• Step 1: Take photos/short videos of your issue.
• Step 2: Send a brief description of the problem, problem photos or videos, order number, and purchase platform to service@engwe-bikes.com.
• Step 3: We will diagnose your problem, and ifthe problem is clear, we will provide a solution.
• Step 4: When encountering problems that cannot be diagnosed initially, we will send you a troubleshooting file that will require you to perform tests according to our testing methods and provide corresponding videos or photos. We will provide a solution after receiving the testing videos or photos.
• Step 5: We will verify your order information and delivery address, and resend the corresponding accessories to you.

Contact Us

1. Tell:
   +33 805980036 (EU) Business hours: 9 am to6 pm (Greenwich Mean Time +l), Monday to Friday
   +18442007117 (USA) Business hours: 9 am to 6 pm (Pacific Standard Time,Starting at 8 am), Monday to Friday

2. Email:

   • service@engwe-bikes.com.
   • We usually reply within 1 working day.

Disclaimer

Please read the following carefully before using this electric bike. This disclaimer details your rights, responsibilities, and limitations when using the electric bike. By using this product, you agree to and accept the following terms:

1. Users must comply with all local laws and regulations, including but not limited to traffic rules, cycling safety standards, and legal restrictions on the use of this electric bike.
2. The vendor is not responsible for any malfunctions, accidents, or damages caused by the user’s failure to operate, maintain, and adjust this product according to the user manual, maintenance manual, or safety guide.
3. Users are not allowed to disassemble, repair, or modify this product unless explicitly authorized by the vendor in writing. Any unauthorized modifications will void the warranty and increase the risks of use.
4. This product may involve certain risks, including but not limited to cycling accidents, falls, accidental collisions, or injuries. Users are responsible for their personal safety and should take appropriate safety measures when using this product.
5. The warranty for this product is limited to the defects and faults specified by the vendor. Damages, wear and tear, normal fatigue, or problems caused by accidents, improper use, storage, or maintenance are not covered by the warranty.
6. The vendor is not responsible for any damages or losses caused by logistics transportation. Users should inspect the packaging upon receipt and promptly contactthe vendor to resolve any issues.
7. None of the terms in this disclaimer shall diminish the rights of users provided by applicable laws and regulations. Please read and understand the above disclaimer carefully before using this product. If you do not agree with any of the terms, please do not use this electric bike. If you have any questions about any content in this disclaimer, please contact the vendor for further explanation and guidance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>