BOSCH SMP4ECC71S Dishwasher Under Bench Instruction Manual

BOSCH SMP4ECC71S Dishwasher Under Bench

Specifications

• Water hardness settings: Soft, Medium, Hard, Very Hard
• Programmes: Multiple with varying durations, energy consumption, and water usage
• Special features: Home Connect app compatibility, water softening system, special salt dispenser, rinse aid dispenser

Product Usage Instructions

Setting up Home Connect:

1. Install the Home Connect app on your mobile device.
2. Scan the QR code with the Home Connect app.

Setting the Water Softening System:

1. Press the designated button.
2. Hold the button for 3 seconds to access appliance settings.
3. Use the buttons to set the water hardness level.
4. Save the settings by holding the button for 3 seconds.

Adding Special Salt:

1. Unscrew and remove the lid of the special salt dispenser.
2. Fill with water on initial start-up.
3. Add special salt to the dispenser.
4. Close the lid securely.

Adding Rinse Aid:

1. Open the lid of the rinse aid dispenser.
2. Add rinse aid up to the max mark.
3. Close the lid securely.

Adding Detergent:

1. Add the detergent to the dry detergent dispenser following recommended quantities.
2. Close the lid securely.

How to Use Your Appliance:

1. Load suitable tableware into the dishwasher after removing large food remnants.
2. Add detergent to the dispenser.
3. Switch on the appliance.
4. Select the desired programme.
5. Start the programme.
6. Remove tableware at the end of the programme.
7. To cancel a programme, press the designated button for approximately 4 seconds.

Cleaning Filters:

1. After each wash, check and clean the filters for residue.
2. Remove and clean both the coarse and micro filters regularly.

Frequently Asked Questions (FAQ)

• How often should I add rinse aid?
  It is recommended to check and refill rinse aid in the dispenser whenever it falls below the max mark, typically before starting a new cycle.

• Can I use regular table salt instead of special salt?
  No, only use special salt designed for dishwashers to avoid damage to the appliance.

• What should I do if my appliance doesn’t connect to the Home Connect app?
  Ensure your mobile device and appliance are connected to the same Wi-Fi network and try restarting both devices before attempting to connect again.

Setting up Home Connect

Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.

1. Install the Home Connect app on your mobile device and follow the instructions.
2. Scan the QR code with the Home Connect app.

Overview of water hardness settings

• You can find an overview of the water hardness values that can be selected here.
• A table of country-specific units can be found in the instruction manual.

Setting the water softening system

1. Press ⁠ .
2. To open the appliance settings, press Setup 3 sec. for 3 seconds. flashes.
3. Press Start repeatedly until the right water hardness has been set. 0, 1, 2 or 3 LEDs will light up accordingly.
4. To save the settings, press Setup 3 sec. for 3 seconds.

Programmes

• The programme data has been measured in the laboratory according to European standard EN 60436.
• The consumption figures depend on the programme and additional function selected.
• The running time will change if the rinse aid system is switched off or rinse aid needs to be added.

USING INSTRUCTION

Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts.

1. Unscrew the lid of the dispenser for special salt and remove.

2. On initial start-up: Fill the dispenser right up with water.

3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.

4. Place the lid back on the dispenser and turn to close.

Adding rinse aid

1. Press the catch on the lid of the dispenser for rinse aid 1 and lift ⁠2.

2. Add rinse aid up to the max mark.

3. Close the lid of the dispenser for rinse aid.
   The lid clicks into position.

Adding detergent

1. Add the detergent to the dry detergent dispenser.

2. Close the lid of the detergent dispenser.
   The lid clicks into position.

How to use your appliance

1. Load the tableware.
   Only clean tableware that is suitable for dishwashers.
   Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.

2. Add detergent.

3. Switch on the appliance ⁠Start.

4. Select the programme.

5. Start the programme ⁠Reset 4 sec.

6. Remove the tableware at the end of the programme.

7. To cancel the programme, press for approx. 4 seconds.
   The programme is cancelled and ends after approx. 1 minute.

Cleaning filters

1. After each wash check the filters for residue.

2. Turn the coarse filter anticlockwise 1 and remove the filter system ⁠2.

3. Pull down the micro filter to remove.

4. Press the locking catches 1 together and lift the coarse filter out ⁠2.

5. Clean the filter elements under running water.

6. Re-assemble the filter system.

7. Insert the filter system into the appliance and turn the coarse filter clockwise.
   Make sure that the arrow markings match up.

Cleaning spray arms

1. Unscrew the upper spray arm 1 and pull down to remove ⁠2.

2. Pull up the lower spray arm to remove.

3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.

4. Insert the lower spray arm.
   The spray arm clicks into position.

5. Insert the upper spray arm and screw it firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.

2. Remove the filter system.

3. Scoop out any water.

4. Prise off the pump cover using a spoon and grip it by the crosspiece.

5. Lift the pump cover inwards at an angle and remove.

6. Remove any remnants of food and foreign bodies in the area of the impeller.

7. Insert the pump cover 1 and press down ⁠2.
   The pump cover clicks into position. 1

8. Install the filter system.

Troubleshooting

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>