OLT RB128DFO-2X4 12×8 Deer Proof Raised Garden Bed Installation Guide
- June 13, 2024
- OLT
Table of Contents
12’X8’ Garden in a Box (2×4 Panels)
Deer Fence Option Kit
Item# RB128DFO-2X4
Revision #1.2
04/11/2024
RB128DFO-2X4 12×8 Deer Proof Raised Garden Bed
Thank you for purchasing a 12’ x 8’ Raised Garden Bed Deer Fence Option Kit.
Please take the time to identify all the parts prior to assembly.
Please use Safety Eyewear and Gloves while Assembling. Be sure to read and
follow all operating instructions for any tools used during assembly.
Remember- NO SAW CUTTING IS REQUIRED!
Safety Points and Other Considerations Please follow this instruction manual
when assembling your Raised Garden Bed Deer Fence Option Kit and retain the
manual for future maintenance purposes.
Estimated Assembly Time for the Deer Fence Kit = 1 Hour.
Safety Equipment Required
(Not Provided)
In the event of a missing or broken piece, simply call the Outdoor Living
Today Customer Support Line @
1-888-658-1658 within 30 days of the
delivery of your purchase. It is our commitment to you to courier replacement
parts, free of charge, within 10 business days of this notification.
Replacement parts will not be provided free of charge after the 30 day grace
period.
Exploded View and Parts List for 12×8 Raised Bed Deer Fence Option Kit
Parts List
Part 1 | 9 pcs – Side/Rear Deer Fence Panels (46”wide x 33 1/2”high) |
---|---|
Part 2 | 2 pcs – Door Deer Fence Panels (22 3/4”wide x 33 1/2”high) |
Part 4 | 4 pcs – Corner Brackets (angle cut ends) (1 1/2” x 1 1/2” x 24”) |
Part 5 | 4 pcs – Vertical Panel Supports – Long (3/4” x 2 1/2” x 45”) |
Part 6 | 4 pcs – Vertical Panel Supports – Short (3/4” x 2 1/2” x 22”) |
Hardware Kit (Provided)
Tools Required (Not Provided)
-
Prior to installing your Deer Fence Option Kit, confirm your 12×8 Raised Bed is level and square.
Measure diagonally inside corner to corner (approximately 164 1/4”) in both directions. Adjust as required. Use a level to determine if the tops of the bed frames are sloped and adjust if necessary.
We recommend filling your raised bed with soil prior to installing your Deer Fence Option Kit. -
Starting on the side of the rear corner, position the frame of a Side Panel (1) – 46” wide x 33 1/2” high directly on top of the raised bed frame. Screw frames together with 4- 2 1/2” Screws as shown on the left. Install panels with the 1 1/2” thick side on top.
Expert Advice: Use a Wood Clamp when positioning and attaching deer fence panels together. -
Position a Rear Panel (1) – 46” wide x 33 1/2” high directly on top of the side raised bed frame. Hold both deer fence frames together and starting at the top, screw together with 5 – 2 1/2” Screws as shown on the left. Screw bottom of frame down to raised bed frame with 4 – 2 1/2” Screws.
-
Position a second Rear Panel (1) – 46” wide x 33 1/2” high on top of the rear raised bed frame. Hold both rear deer fence frames together and starting at the top, screw together with 4 – 2 1/2” Screws as shown above. Screw bottom of frame down to raised bed frame with 4 – 2 1/2” Screws. Complete remaining side and rear panels attachments following Steps 2 and 3.
-
Locate both Deer Fence Door Panels (2) – 22 3/4” wide x 33 1/2” high. Position and install both Door Panels, screwing only from bottom frame into top of raised bed door frame with 3 – 2 1/2” screws per panel as shown above.
-
Locate all four Black Plastic Hinges (3) and attach to deer fence frame with 6 – 3/4” black screws per hinge as shown above. Use 1/8” drill bit to pilot hole shallow holes before attaching to avoid splitting deer fence framing. Open and close door to check door aligned correctly. Adjust as required.
-
Attach Corner Brackets with angle cut ends – (4) on the inside frames at the top. Use 2 – 2 1/2” Screws per bracket. Screw on an angle. Pre-drill ends with 1/8” drill bit to prevent wood splitting.
-
Locate Vertical Panel Supports – Long (5) – 3/4” x 2 1/2” x 45” and Vertical Panel Supports – Short (6) – 3/4” x 2 1/2” x 22”. Starting with 45” long support first, center on panel frames, flush at bottom and attach with 4 – 2” Screws. Offset the screw to either side of the support to ensure you contact the heart of the bed frame.
-
Position and attach short Vertical Panel Support using 3 – 2” Screws as per Step 7. Complete remaining rear and side walls.
-
Attach Black Barrel Bolt to door and panel frame using 6 – 3/4” Black Screws. Note how female part of Barrel Bolt is positioned higher than male. Do a dry run first to position Barrel Bolt correctly, then attach.
Pre-drill with 1/8” drill bit to prevent wood from splitting.
We hope your experience assembling our 12’x8’ Raised Garden Bed Deer Fence Option Kit has been both positive and rewarding. We value your feedback and would like to hear back from you on how well we are doing in the following areas:
- Customer Service
- On Time Shipping
- Motor Freight Delivery
- Quality of Materials
- Assembly Manual
- Overall Satisfaction.
Please call, write or email us at:
Canadian Address
9393 287th Street
Maple Ridge, British Columbia
Canada V2W 1L1| United States Address
P.O. Box 96
Sumas, Washington
USA 98295
---|---
The materials contained in this Assembly Manual may be downloaded or copied provided that ALL copies retain the copyright and any other proprietary notices contained on the materials. No material may be modified, edited or taken out of context such that its use creates a false or misleading statement or impression as to the positions, statements or actions.
Toll Line: 1.888.658.1658
Fax: 1.604.462.5333
www.outdoorlivingtoday.com
sales@outdoorlivingtoday.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>