LITHEAUDIO 06610 Wi-Fi Ceiling Speaker Instruction Manual
- June 4, 2024
- LITHEAUDIO
Table of Contents
Ceiling Speaker
Instruction Manualhttps://www.litheaudio.com/register-product.html
Don’t FORGET TO REGISTER YOUR SPEAKER:
WWW.LITHEAUDIO.COM/REGISTER
06610 Wi-Fi Ceiling Speaker
THANK YOU FOR CHOOSING LITHE AUDIO
Innovative design and advanced engineering are built into our wireless Wi-Fi
ceiling mount speakers. Designed for easy installation and high-quality sound,
within seconds each room is set up and ready. This manual describes the
installation of the speakers within the conventional stud and sheetrock (Joist
and plasterboard) ceilings.
IMPORTANT SAFETY WARNING
BEFORE USE PLEASE READ COMPLETELY AND USE THE PRODUCT IN ACCORDANCE WITH
THESE SAFETY INSTRUCTIONS.
Before commencing any electrical work ensure the supply is switched OFF at the
mains. Either by switching off the consumer unit or by removing the
appropriate fuse. This product should be installed in accordance with the
relevant sections of the building regulations code and in accordance with the
latest edition of IEE regulations (BS 7671).
If the unit is to be used as a replacement for an existing product, remove the
existing unit from its location and disconnect the wiring. Connect the wires
as shown in the diagram. Ensure terminals are properly tightened and ensure no
bare wires are visible. When fitting the speaker into the ceiling, ensure no
wires are trapped.
READ THE INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION PROCESS
AND KEEP THEM SAFE FOR FUTURE REFERENCE.
- Failure to follow the instructions in this guide voids all warranties on your speakers.
- Warning: Do not use the product in water
- Warning: Do not install the speaker directly above any heat sources such as radiators, or other apparatus that produce heat
- Warning: To reduce the risk of fire or electric shock, do not expose this speaker to rain or moisture (directly above the bath or shower area) or in Bathroom Zone 0 or Zone I.
- Protect the power cable from being damaged, do not overstretch the cable.
- Only use attachments/accessories specified by the manufacturer Lithe Audio.
- Turn off the power to the speaker when unused for long periods of time.
- A Fire and Acoustic speaker hood must be used in accordance with UK building and IEE Regulations with a fire rating of up to 60 minutes and is Parts B, L, C, and E compliant.
- Do not open the back cover to the speaker as this protects the PCB as this will invalidate the warranty and could cause electric shock
- Ensure speaker location is free from obstructions such as electrical conduit, HVAC ducts or Water lines.
USA REGULATIONS
BEFORE USE PLEASE READ COMPLETELY AND USE THE PRODUCT IN ACCORDANCE WITH
THESE SAFETY INSTRUCTIONS.
The Power adaptor (supplied) should not be placed in a dead space such as a
wall or ceiling. In accordance with US National Electrical Code. A DC
extension cable must be used in conjunction with the power adaptor supplied
and placed inside / on top of a cabinet or anywhere where you have
accessibility. (Each situation is unique to the installation, consult your
local building codes or contact Authorized Dealer or Installer)
If the unit is to be used as a replacement for an existing product, remove the
existing unit from its location and disconnect the wiring. Connect the wires
as shown in the diagram. Ensure terminals are properly tightened and ensure no
bare wires are visible. When fitting the speaker into the ceiling, ensure no
wires are trapped.
READ THE INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION PROCESS
AND KEEP THEM SAFE FOR FUTURE REFERENCE.
- Failure to follow the instructions in this guide voids all warranties on your speakers.
- Warning Do not use the product in water
- Warning: Do not install speaker directly above any heat sources such as radiators, or other apparatus that produce heat
- Protect the power cable from being damaged, do not overstretch the cable.
- Only use attachments/accessories specified by the manufacturer Lithe Audio.
- Turn off the power to the speaker when unused for long periods of time.
- A Fire and Acoustic speaker hood must be used in accordance with UK building and IEE Regulations with a tire rating of up to 60 minutes, is Parts B, L, C, and E compliant.
- Do not open the back cover to the speaker as this protects the PCB as this will invalidate the warranty and could cause electric shock.
- Ensure speaker location is free from obstructions such as electrical conduit, HVAC ducts or Water linac
BOX CONTENTS
Please ensure you read the entire instruction manual carefully before you
commence any work. Carefully unpack the speakers from the packaging. Please
check to ensure all the parts shown below are included.
If any parts of the speaker appear damaged, please contact your
dealer/reseller immediately or contact
www.Litheaudio.com for contact details.
PREPARATION
EQUIPMENT YOU WILL NEED
Listed below is the hardware equipment needed to install the speaker, with
the addition of a ladder to ensure the installation is done safely. A cutting
template is included in the box.
KNOW YOUR SPEAKER
The Lithe Audio LWF1V2 range of Wi-Fi ceiling wireless speakers has various
inputs and outputs:
SPEAKER -To connect one additional passive (Slave) speaker (Gold Plated)
RCA INPUT- To connect directly from existing Hi-Fi equipment
POWER INPUT- To connect (as supplied) transformer
In built over voltage, under voltage, over temperature, and short circuit protection, if there is an electrical fault, the power supply to the amplifier will cut off automatically and restart when the speaker has stabilized.
SPEAKER PLACEMENT
IMPORTANT: BEFORE COMMENCING ANY WORK, DETERMINE YOUR PRIMARY LISTENING
POSITION. IF YOU ARE UNSURE SEEK HELP FROM AN AV INSTALLER FOR OPTIMUM
RESULTS.
2 SPEAKER PLACEMENT
In an ideal scenario, the two speakers should be spaced equally apart from the
primary listening position. Where possible, place the speakers approx 3″ / I m
from the wall
4 SPEAKER PLACEMENT
Ideally, the two speakers to the front and two speakers to the rear should be
spaced equally apart from the primary listening position to provide a balanced
listening experience. Where possible, place the speakers at approx 3″ / I m
from the wall.
NOTE: For optimal sound when using speakers in vaulted ceilings switch the environmental equalizer switch to +3dB, when using speakers in a tiled environment (Bathroom) switch the equalizer to -3dB.
INSTALLATION
IMPORTANT: BEFORE COMMENCING ANY ELECTRICAL WORK ENSURE THE SUPPLY IS SWITCHED OFF AT THE MAINS. IF YOU ARE UNSURE HOW TO FIT SEEK HELP FROM A PROFESSIONAL ELECTRICIAN / AV INSTALLER
I . Mark out the position of the speaker using a tape measure and mark using a
pencil with the template supplied. Check using a stud finder to make sure no
obstruction is present prior to cutting.| 2. Drill a pilot hole and cut the
speaker hole using a cutting saw. Take caution when cutting to keep fingers
away from the cutting blades and wear protective eyewear.
3. Connect the power lead from the transformer (supplied) to an I 3A mains
plug socket or terminate to a dedicated 3A fused spur. Ensure the power lead
is not overstretched.| 4. Insert the speaker into the ceiling then using a
screwdriver lock the 4 dog leg fixings to secure the speaker in place, do not
over-tighten. Attach the magnetic grille to the speaker front.
PAINTING THE SPEAKER GRILLE
Do not paint the speaker grilles whilst attached to the speaker. Lithe Audio
recommends spray painting using 5 parts thinning agent to I part paint. Spray
thinly to ensure speaker cover grille holes are not blocked as this will
affect the sound quality of the speakers.
INSTALLATIONS IN FIRE-RATED CEILINGS
If you plan to mount your speakers in a fire-rated ceiling, you should
purchase a fire hood for the speaker visit
www.litheaudio.com for more information and
recommended hoods.
INSTALLATION USA
IMPORTANT: BEFORE COMMENCING ANY ELECTRICAL WORK ENSURE THE SUPPLY IS SWITCHED OFF AT THE MAINS. IF YOU ARE UNSURE HOW TO FIT SEEK HELP FROM A PROFESSIONAL ELECTRICIAN / AV INSTALLER
I . Mark out the position of the speaker using a tape measure and mark using a
pencil with the template supplied. Check using a stud finder to make sure no
obstruction is present prior to cutting.| 2. Drill a pilot hole and cut the
speaker hole using a cutting saw. Take caution when cutting to keep fingers
away from the cutting blade and wear protective eyewear.
3. To meet the NEC code for this type on install, connect the DC extension
cable to power adap-tor and place power adapter inside/ on top of cabinet or
anywhere you have easy access.| 4. Insert speaker into the ceiling then using
a screwdriver lock the 4 dog leg fixings to secure the speaker in place, do
not over tighten. Attach the magnetic grille to the speaker front.
PAINTING THE SPEAKER GRILLE
Do not paint the speaker grilles whilst attached to the speaker. Lithe Audio
recommends spray painting using 5 parts thinning agent to I part paint. Spray
thinly to ensure speaker cover grille holes are not blocked as this will
affect the sound quality of the speakers.
INSTALLATIONS IN FIRE-RATED CEILINGS
If you plan to mount your speakers in a fire-rated ceiling, you should
purchase a fire hood for the speaker. Visit
www.litheaudio.com for more information and
recommended hoods.
YOUR HOME WI-F1 NETWORK
To enable the Lithe Audio Wi-Fi ceiling speakers, your device must be on the same network.
- Ensure your network has a high-speed internet connection, as the speakers are designed to provide you with free online software/firmware updates.
- High-speed DSL / cable modem or fiber to the home broadband is recommended for the best possible playback of music services.
- Lithe Audio communicates over a 2.4GHz & 5GHz Wi-Fi home network supporting 802.1 I a, b, g, n, ac wireless technology only.
- For larger homes where the Wi-Fi signal is not stable, we suggest adding access points/mesh networks to strengthen the network or updating your router to a higher specification model to suit the demand.
LITHE AUDIO APP
- To enhance your listening experience download the Lithe Audio app via the app store on your device and follow the setup procedures within this instruction manual.
- The app will allow you to set up singular rooms, and groups of speakers or play in Party Mode.
- You can connect multiple speakers simultaneously and control them all from the app.
STATUS INDICATOR LIGHT
Located on the front face of the speaker, the LED Indicates the status of your speaker:
- Red solid: Speaker booting up
- Red quick flash (Is 4 times): Speaker under restart operation
- Red slow flash (3s I time): Speaker under standby mode, waiting for user operation
- Green solid: Speaker is active and connected to Wi-Fi
- Blue Solid: Bluetooth speaker connected
- Green slow flash( I s I time): Speaker trying to connect to the preconfigured Wi-Fi
- Solid purple: Speaker under RCA mode
- Green quick flash( I s 4 times): Speaker in WAC/SAC mode, user to configure Wi-Fi
CONNECTING TO BLUETOOTH
I. Open the setting menu and select Bluetooth| 2. Turn on Bluetooth and search devices
3. Click Lithe Audio Speaker to connect and pair to the speaker
SETUP FOR APPLE IOS
I . Ensure the Wi-Fi speaker is connected to the power supply and is turned
on, The LED indicator light will be red.
2. Press and hold the ‘Connection Reset Button’ for I 0 seconds & release,
the LED indicator will flash Green fast and the speaker is now ready to
connect to your Wi-Fi network.
3. Open the Wi-Fi setting menu on your phone or tablet| 4. Select the new
AirPlay speaker listed you would like to add to your network
5. Select your network and change the ‘Speaker Name’ to something easily
identifiable e.g. Kitchen and click Next| 6. The Lithe Audio Wi-Fi speaker
setup is now complete, return to the Lithe Audio app
The image shows Apple Phone but the visuals may change from device to
device.
Apple and ‘Phone are trademarks of Apple Inc.. registered in the U.S. and
other countries.
WWW.LITHEAUDIO.COM
Documents / Resources
|
LITHEAUDIO 06610 Wi-Fi Ceiling
Speaker
[pdf] Instruction Manual
06610 Wi-Fi Ceiling Speaker, 06610, Wi-Fi Ceiling Speaker, Ceiling Speaker,
Speaker
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>