LITHEAUDIO 03200 6.5 Inch Bluetooth Ceiling Speaker Instruction Manual

LITHEAUDIO 03200 6.5 Inch Bluetooth Ceiling Speaker

THANK YOU FOR CHOOSING LITHE AUDIO

Innovative design and advanced engineering come as standard in our LBT series of wireless Bluetooth ceiling speakers. Designed for easy installation and high-quality sound, within minutes each room is set up and ready. This manual details the installation of LBT series speakers within the conventional stud and sheetrock (Joist and plasterboard) ceilings.
IMPORTANT SAFETY WARNING
Before use please read completely and use in accordance with these safety instructions.
Before commencing any electrical work ensure the supply is switched OFF at the mains. Either by switching off the consumer unit or by removing the appropriate fuse. This product should be installed in accordance with the relevant sections of the building regulations code and in accordance with the latest edition of IEE regulations (BS 7671).
If the unit is to be used as a replacement for an existing product, remove the existing unit from its location and disconnect the wiring. Connect the wires as shown in the diagram. Ensure terminals are properly tightened and ensure no bare wires are visible. When fitting the speaker into the ceiling, ensure no wires are trapped.
READ THE INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION PROCESS AND KEEP THEM SAFE FOR FUTURE REFERENCE.

• Failure to follow the instructions in this guide voids all warranties on your speakers.
• Warning: Do not use the product in water.
• Warning: Do not install speaker directly above any heat sources such as radiators, or other apparatus that produce heat.
• Warning: To reduce the risk of fire or electric shock, do not expose this speaker to rain or moisture (directly above the bath or shower area) or in Bathroom Zone 0 or Zone 1.
• Protect the power cable from being damaged, do not over-stretch the cable.
• Only use attachments/accessories specified by the manufacturer Lithe Audio.
• Turn off the power to the speaker when unused for long periods of time.
• A Fire and Acoustic speaker hood must be used in accordance with UK building and IEE Regulations with a fire rating of up to 60 minutes and is Parts B, L, C, and E compliant.
• Do not open the back cover to the speaker as this protects the PCB, doing so will invalidate the warranty and could cause electric shock.
• Ensure speaker location is free from obstructions such as electrical conduit, HVAC ducts, or Water lines.

BOX CONTENTS

Please ensure you read the entire instruction manual carefully before you commence any work. Carefully unpack the speakers from the packaging. Please check to ensure all the parts shown below are included. If any parts of the speaker appear damaged, please contact your dealer/reseller immediately or contact info@litheaudio.com for contact details.

PREPARATION EQUIPMENT YOU WILL NEED
Listed below is the hardware equipment needed to install the speaker, with the addition of a ladder to ensure the installation is done safely. A cutting template is included in the box.

KNOW YOUR SPEAKER

The Lithe Audio LBT2 range of Bluetooth ceiling wireless speakers has various inputs: SPEAKER OUTPUT – To connect one additional passive (Slave) speaker (Gold Plated) LITHE-LINKTM – Connect 2 additional LBT speakers (Total 3 masters & 3 passives) RCA INPUTS – To connect directly from TV Output, Amazon echo dot, DVD Player, etc. POWER INPUT – To connect (as supplied) transformer

INSTALLATION

IMPORTANT: BEFORE COMMENCING ANY ELECTRICAL WORK ENSURE THE SUPPLY IS SWITCHED OFF AT THE MAINS. IF YOU ARE UNSURE HOW TO FIT SEEK HELP FROM A PROFESSIONAL ELECTRICIAN/AV INSTALLER

1. Mark out the position of the speaker using a tape measure and mark using a pencil with the template supplied. Check using a stud finder to make sure no obstruction is present prior to cutting.
2. Drill a pilot hole and cut the speaker hole using a cutting saw. Take caution when cutting to keep fingers away from the cutting blade and wear protective eyewear.
3. Connect the power lead from the transformer (supplied) to a 13A mains plug socket or terminate to a dedicated 3A fused spur. Ensure the power lead is not overstretched.
4. Insert the speaker into the ceiling then using a screwdriver lock the 4 dog leg fixings to secure the speaker in place, do not over tighten. Attach the magnetic grille to the speaker front.

PAINTING THE SPEAKER GRILLE
Do not paint the speaker grilles whilst attached to the speaker. Lithe Audio recommends spray painting using 5 parts thinning agent to 1-part paint. Spray thinly to ensure speaker cover grille holes are not blocked as this will affect the sound quality of the speakers.
INSTALLATIONS IN FIRE-RATED CEILINGS
If you plan to mount your speakers in a fire-rated ceiling, you should purchase a fire hood for the
speaker. Visit www.litheaudio.com for more information and recommended hoods.

SETUP AND PAIRING

NOTE: ENSURE THE BLUETOOTH WIRELESS SPEAKER IS CONNECTED TO
THE POWER SUPPLY AND TURNED ON.
The Led indicator will flash Blue when ready to pair, and turn solid Blue whilst the device is connected to the speaker and music is playing

1. Open the setting menu and select Bluetooth
2. Turn on Bluetooth and search devices
3. Click Lithe Audio BT2 to connect and pair to the speaker.
4. Open your phone camera and scan the below QR code and then download the Setup App to change speaker name or add a pin:

BLUETOOTH SETUP APP

Have multiple speakers in the home? Use this App to set up & identify each speaker easily by giving each a unique name and if want to give a password. You can also configure it so the speaker works with Amazon Alexa, Google Home, or TV wirelessly. For more information visit:
www.litheaudio.com/bluetooth-5-setup- app.html

HARD WIRED INPUT- RCA INPUT

To connect other devices that may not have a Bluetooth connection (such as Turn tables, CD players, mp4 players, or mini-discs!)
RCA CONNECTION: To play music via speaker RCA connection connect an RCA cable to the speaker and play through your device. Ensure ALL Bluetooth connections are turned off to be able to play through the speaker. The LED will turn green when playing using RCA.

ADDITIONAL SPEAKER – OPTIONAL

PLEASE NOTE: LBT1 DOES NOT INCLUDE PASSIVE SPEAKER
With the Lithe Audio Master Bluetooth ceiling the speaker is able to connect to and power an additional passive speaker via the speaker out-put (+/-). Use wire cutters to strip the ends of the speaker cable (if required). This setup is ideal for Kitchen diners or larger rooms where you want a true stereo setup.

LITHE-LINKTM SETUP

For larger or open-plan rooms the Lithe-link feature will allow you to connect up to 3 master speakers and their passive/slaves and play audio from all the speakers at once. Depending on which master speaker you connect to and how the speakers are wired will then determine how many speakers will play. For larger or open-plan rooms the Lithe-link feature will allow you to connect up to 3 master speakers and their passive/slaves and play audio from all the speakers at once. Depending on which master speaker you connect to and how the speakers are wired will then determine how
many speakers will play. To connect the speakers you will need a 3.5mm to 3.5mm Jack cable (Not supplied, as length will vary in all situations) Connect one end to the Line OUT (Pink connector block) and the other to the Line IN (Green connector block)

SETUP WITH FULL LOOP CONNECTION
Adding a connection between the first and last master speaker will create a full loop system. When connected to whichever master speaker you connect to, all the masters and their passive speakers will play. This will ensure in a large room you will always be within the range of a speaker to connect to.
This setup is ideal for open-plan rooms where you always want all speakers to play at once.
SETUP WITHOUT FULL LOOP CONNECTION
This configuration will allow you to play only the speaker you connect to and the masters and passives connect after it with the link cable. For Example, if you have a 6-speaker setup and you connect to Speaker A then speakers A, B, and C will play. If you connect to Speaker B then only speakers B and C will play. Connect to Speaker C then only Speaker C will play. This setup is ideal for a floorplan with multiple areas or rooms where you may not always
want to play the whole area at once.

LITHE-LINK SPEAKER SETUP OPTIONS

STEREO / MONO SELECTOR
If using a secondary passive speaker you can select if the music is played in Stereo (left and right channels) or in Bridged Mono (single channel). Use the switch on the back of the speaker to select Stereo or Mono output.
VOLUME CAPPING SWITCH
If installing in a hotel room or commercial space you may wish to cap the volume at 50%. Using the Volume capping switch on the back of the speaker you can select either 100% or 50% max volume output.
LED INDICATOR COVER
To mask the LED indicator, use the LED cover sticker included
CONNECTION RESET BUTTON
Press and hold the ‘Reset Button’ for 2 seconds to clear the connection memory.
All paired devices will be deleted.

SPECIFICATIONS

• Sound Quality THD+N<0.009%, 55Hz-20kHz
• RMS Power: 50W RMS
• Impedance: 8 Ohms
• Sensitivity (1W/1m): 90dB
• Audio Sample Rate: 8Khz
• Line In Analog (RCA), auto-detecting
• Type: Class D (Digital)
• Woofer: 6.5” Kevlar Woven / Polypropylene Cone
• Tweeter: 0.75” Titanium Cone
•  Bluetooth System: Bluetooth 5.0
• Aptx – Low Latency
• Frequency Range: 2.4GHz – 2.4832GHz (ISM Band)
• RF Channels: 79 (USA, Japan & EU)
• Wireless Range: Up to 30 metres
• ID Device Name: Lithe Audio BT2
• Power Input Supply : 100 – 240V ~ / 2A
• Transformer Output Supply : DC24V / 2.5A
• Dimensions (W x D) 230 x 95mm (6.5 x 3.8 in)
• Weight 1.75kg (3.85 lbs)
• IP rating: IP44 (Model: LBT2/IP
• Operating Temperature 0º to 40º C (32º to 104º F)
• Storage Temperature -20º to 70º C (4º to 158º F)
• Standby power: 1.3W / 0.02A
• Connected power: 1.5W / 0.03A
• Playing Music: 2.8W – 10.5W / 0.03A – 0.09A**
• Specifications subject to change without notice.
•  Power Consumption depends on the type of music & volume –
• Increased Bass & volume requires more power loading on the amplifier.

TROUBLESHOOTING

If a problem arises, please try the troubleshooting frequently asked guide below. If the problem is not listed please contact Lithe Audio Customer Service Support at support@litheaudio.com or Call +44 (0) 1293 922 015
Speaker has not been found during the setup
Please check power cord is correctly connected to the speaker and transformer, Check if the blue light is flashing. Press the reset button for 10 seconds to reboot the speaker.
Before commencing any electrical work ensure the supply is switched OFF at the mains.
Speaker has failed to connect to Bluetooth
Please retry the setup and pairing process, and follow setup steps 1 – 4 to connect the device. Please ensure the speaker password is entered correctly. Ensure the device is within the 30m range. If this does not work, power down the speaker, wait 20 seconds, then power up again and try again.
The device is connected to a Bluetooth speaker but no sound
Ensure your device volume is NOT muted, increase the volume or try another audio source
Can the speaker be installed on the bathroom ceiling?
The IP-rated models ‘LBT2/IP’ can be installed in zone 2 or 3 of a bathroom. Ensure you read the safety precautions on page 1 before installation. Warning: Do not use the product in water or directly above the bath or shower area.
For further queries and support questions please visit www.litheaudio.com/support
REGULATION INFORMATION
EUROPE
LitheAudio declares that this product herewith complies with the requirements of the EMC Directive 2004/108/EC, Low Voltage directive 2006/95/EC, Eco-Design Directive 2005/32/EC, RoHS Directive 2011/65/EU, and the R&TTE Directive 1999/5/EC when installed and used in accordance with the manufacturer’s instructions. A copy of the full Declaration of Conformance may be obtained at www.litheaudio.com/support/policies.
Lithe Audio Speakers have a standby mode or remove the power cord from the AC mains.

RECYCLING INFORMATION

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste.
Instead please deliver it to the applicable collection point for the recycling of electrical and electronic equipment. By recycling this product correctly, you will help conserve natural resources and prevent potential negative environmental consequences. For more detailed information about recycling this product, please contact your local council office, your household waste disposal service, or the shop where you purchased the product(s) from.

2 YEAR GUARANTEE

This Ceiling Speaker is of excellent quality and construction. However, if any defects in materials or workmanship do appear during the guarantee period, we will, at our discretion, either repair or replace the defective parts, free of charge, subject to the terms and conditions of our Guarantee shown below.
This Guarantee covers both parts and labor. Carriage is not included. This Guarantee provides benefits that are additional to, and do not affect, your statutory rights. This Guarantee does not cover the cost of returning the product to the dealer from whom it was purchased or to ourselves. This Guarantee applies only to products sold and located in mainland Great Britain. It does not cover liability in respect of or replacement of plugs, cables, or fuses and also does not cover defects due to:

• Failure to use or maintain the product in accordance with Lithe Audio instructions.
• The product is connected to an unsuitable electricity supply.
• Accidental damage to or abuse or misuse of the product.
• Product modification, except by Lithe Audio or an approved agent.
• Dismantling of or interference with the product.
• Before returning any product under this Guarantee, please check that:
• You have followed the product instructions correctly.
• Your mains electricity supply is functional.
• The defect is not due to a blown fuse. If you wish to claim under this guarantee you should:
• Send the product, postage or carriage paid, to the dealer from whom it was purchased or to Lithe Audio direct.
• Ensure that the product is clean and packed carefully (preferably in its original carton).
• Enclose details of your name, address, and telephone number and when and where the product was purchased, together with proof of purchase (e.g. an invoice or till receipt).
• Give exact details of the nature of the defect. This Guarantee does not cover any other claims whatsoever, including, without limitation, any
• liability for incidental, indirect, or consequential damage, nor does it cover any claims for conversion or modification or for the costs of repair carried out by any third party without the prior consent of Lithe Audio. If replacement parts are fitted to the product this will not extend the period of the
• Guarantee. For further advice contact Lithe Audio customer services.

References

• Wireless Audio Solutions - Lithe Audio LTD
• Bluetooth 5 Setup App - Lithe Audio LTD
• Bluetooth Ceiling Speakers | WiFi Ceiling Speakers | Garden Bluetooth Rock Speakers | Motorised TV Brackets | Hotel Audio Solutions | Support - Lithe Audio LTD

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>