MOTOROLA SOLUTIONS MXP600 Extreme Temperature Animation Installation Guide

MOTOROLA SOLUTIONS MXP600 Extreme Temperature Animation

Specifications

• Submersible radio compliant with IP67 standard
• The front camera and rear camera with flash
• Touch screen display with LTE/Device Status LED and TETRA Status LED
• Front microphone, front speaker, rear microphone, and earpiece speaker
• Power button, Push-To-Talk Button (PTT), and emergency button
• USB-C connector for charging and GCAI-Mini connector

Product Usage Instructions

To attach the antenna

1. Insert the threaded base of the antenna into the antenna terminal on top of your radio.
2. Turn the antenna clockwise until it is tight.

Installing the Battery
To install the battery:

1. Insert the battery into the compartment until the contacts align and the battery hooks in place.
2. Press down on the battery until it clicks in place.

Removing the Battery

To remove the battery:

1. Slide the Battery Latch to the right and hold it until you can lift the battery out.
2. Lift the battery from the top and pull upwards to disengage it from the battery hooks.
3. Remove the battery from the compartment.

Inserting MicroSD and SIM Cards
To insert MicroSD and SIM cards:

1. Remove the battery.
2. Flip open the MicroSD/TETRA SIM/LTE SIM card door using the finger scoop area.
3. Slide the card holder then flip it open.
4. Insert the card into the holder with a gold contact area facing down.

Turning On/Off the Radio
To turn on the radio, press and hold the Power button for 3 seconds. To turn off, press and hold until the Power Menu appears, then tap Power off.

Using Duplex and Simplex Calls
For simplex calls, speak into the top microphone and listen through the speaker. For duplex calls, speak into the bottom microphone and listen through the earpiece.

Knowing Your Radio

Looking After Your Radio

• Never leave your radio or battery in extreme temperatures (over +85 °C).
• For example, behind a windscreen in direct sunlight.
• The radio is submersible (compliant with the IP68 standard), but only with the battery and antenna attached.
• To clean your radio, use a moistened or antistatic cloth.
• Ensure no contamination is on the gore port membrane, that is the area labelled as VENT on the back of the radio chassis.

Holding Your Radio

The radio has three microphones:

• A top front microphone for Simplex group, dispatcher, or private calls.
• A top back microphone for optional noise cancellation.
• A bottom microphone for Duplex, telephone-like calls.

1. When using high audio, hold your radio vertically with the top microphone 5–10 cm away from your mouth.

2. Speak into the top microphone.

3. Listen through the speaker.

4. Keep the antenna at least 2.5 cm away from your head and body.

5. When using low audio, hold your radio as you would a telephone.

6. Speak into the bottom microphone.

7. Listen through the earpiece.

8. Keep the antenna at least 2.5 cm away from your head and body.

9. Emergency Button

10. LED Status Indicator

11. GCAI-Mini Connector

12. Antenna

13. Rotary Knob

14. Programmable Button

15. Push-To-Talk Button (PTT) Soft Key

16. Near-Field Communication Tag

17. Send Key

18. Bottom Microphone

19. Backlight Sensor

20. Keypad

21. Speaker

22. On/Off/End/Home Key Menu Key

23. Display

24. Top Microphone

25. Earpiece

26. Bottom Connector

Getting Started

Installing the Battery

1. Insert the battery into the compartment at a high entry angle.
2. Slide the battery under the two catches.
3. Press down the battery until it clicks in place.

Removing the Battery

1. Slide the battery latch to the right and hold it.
2. Lift the battery.
3. Remove the battery from the compartment.

Attaching the Antenna

1. Turn off the radio before attaching the antenna.
2. Insert the threaded base of the antenna into the terminal on top of the radio.
3. Turn the antenna clockwise until snug. Do not force.

Turning the Radio On or Off
To turn the radio on or off, press and hold the On/Off key.

LED Status Indicator

Battery Capacity Information

Icons

Status Icons

Using the Terminal

Unlocking the Radio

• To unlock the radio after powering on, enter the code at the prompt.
• The default code is 0000. Your service provider may change this number before you receive your radio.

Unlocking or Locking the Keypad
To unlock or lock the keypad, press the Menu key followed by the * key.

Using the Radio Menu

• To enter the menu, press the Menu key.
• To scroll through the menu, press the Up or
• Down the Navigation button.
• To select a menu item, press the Select soft key or the Right Navigation key.
• To return to the previous level, press Back or the Left Navigation key.
• To exit the menu, press the Back key.

Selecting TMO or DMO
From the home screen, select Options → Trunked Mode or Direct Mode.

Making TMO or DMO Group Calls

1. From the home screen, press the Navigation keys or turn the Rotary Knob to highlight the desired talkgroup.
2. Press Select.
3. Press and hold PTT.
4. Wait for the Talk Permit Tone (if configured) and talk.
5. To listen, release PTT.

Making TMO or DMO Emergency Group Calls

1. Press and hold the Emergency button.
   The emergency alarm is sent automatically (if configured).

2. Press and hold PTT.

3. Wait for the Talk Permit Tone (if configured) and talk. Release PTT to listen.
   If using the Hot Mic feature, wait for the Emergency Mic On message to appear on the display, then talk without pressing PTT.

4. To exit Emergency Mode, press and hold the Exit soft key.

Making Simplex Private Calls

In DMO:

1. From the home screen, dial a number.
2. Press and hold PTT to make a call.
3. Wait for the Talk Permit Tone (if configured) and talk. Release PTT to listen.
4. To terminate the call, press the End key.

In TMO:

1. From the home screen, dial a number.
2. Press PTT to make a call. Wait for the called party to pick up.
3. When the call is connected, press and hold PTT to talk. Wait for the Talk Permit Tone (if configured). Release PTT to listen.
4. To terminate the call, press the End key.

Making Duplex Private, Phone, or PABX Calls

1. From the home screen, dial a number.
2. Press the Send key. The ringtone sounds till the called party answers.
3. To terminate the call, press the End key.

Sending Status Message

1. From the home screen, press the Menu key.
2. Select Messages → Send Status.
3. Highlight the required status message and press the Send key.
4. If the list is empty, enter a 5-digit status message number and press the Send key.

More Information on the Radio
Visit the Motorola Solutions Web site at: http://www.motorolasolutions.com/

Learning Experience Portal
User documentation is available at: https://learning.motorolasolutions.com/

Open Source Software Legal Notices
Available in Customer Programming Software Plus (CPS Plus) DVD

This document is copyright-protected. Duplications for the use of Motorola Solutions products
are permitted to an appropriate extent. Duplications for other purposes, changes, additions or other processing of this document are not permitted. Only this electronically-saved document is considered to be the original. Duplications are considered merely copies. Motorola Solutions, Inc. and its subsidiaries and affiliates do not vouch for the correctness of such kinds of copies.

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and are used under license. All other trademarks are the property of their respective owners.
© 2020 Motorola Solutions, Inc. All rights reserved.

www.motorolasolutions.com

FAQ

• Where can I find more information about the radio?
  • You can visit the Motorola Solutions website at: www.motorolasolutions.com
• How can I access user documentation?
  • User documentation is available at: learning.motorolasolutions.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>