RAIN BIRD ESPBAT-BT1 Battery Powered Bluetooth Irrigation Controllers User Guide

RAIN BIRD ESPBAT-BT1 Battery Powered Bluetooth Irrigation Controllers

FAQ

• Q: What type of batteries does the BAT-BT use?
  • A: The BAT-BT uses 4 x LR6 (AA) Non-rechargeable Alkaline Batteries.
• Q: How can I confirm the batteries are installed correctly?
  • A: Connect the station wires to solenoids and listen for solenoid chatter after battery installation to ensure correct installation.

App Install

Install and setup BAT-BT battery powered Bluetooth Irrigation controllers.

Connect to Valves

• Connect the station wires to DC latching solenoids (e.g. TBOSPSOL) as shown. Doing this first will give you the opportunity to hear the solenoid “chatter” after the batteries are installed.
• This way you can confirm the batteries are in good health, and installed correctly.

Insert Batteries

The BAT-BT is powered by 4 x LR6 (“AA”) Non-rechargeable, alkaline batteries. To insert the batteries:

1. Remove the battery cap (a)
2. Remove the battery holder (b)
3. Place the batteries in the holder being careful to install them with the correct polarity (+ / -)
4. Re-insert the battery holder into the device spring side first
5. Replace the battery cap

Mount in Valve Box

The BAT-BT should be installed in a valve box using one of these 3 methods:

• A. Mounting Peg: The BAT can be hung using the mounting hole.
• B. Cable Tie: Use the provided cable tie to strap the BAT mounting hole to the valve box locking ring or a drilled hole.
• C. Screw Mount: The BAT can also be hung from a screw using the mounting hole.

Connection Strength

• Install the BAT-BT as close to surface level as possible to optimize Bluetooth® signal strength and range.

Pair with Smart Phone

1. Download the Rain Bird app from the App Store or Google Play.
2. Scan the QR code on the top surface of the BAT-BT to begin pairing.
3. Follow the on screen prompts to connect to the controller via Bluetooth® and set it up.

Master Valve (Optional)

• Connect the orange master valve ‘M’ and black common ‘C’ wire as shown.

Rain Sensor (Optional)

• Connect the sensor wires ‘S’ to a compatible sensor

Safety Information

CAUTION

• Only use four non-rechargeable alkaline batteries type LR6 (“AA”). These batteries provide the voltage required by the controller.
• This device must be installed to provide a separation distance of at least 20 cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.v
• RISK OF EXPLOSION IF BATTERY IS REPLACED WITH AN INCORRECT TYPE
• DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

WARNING

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capacity, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Special precautions must be taken when valve wires are located adjacent to, or share a conduit with other wires, such as those used for landscape lighting or other electrical systems.
• Separate and insulate all conductors carefully, taking care not to damage wire insulation during installation. An electrical “short” (contact) between the valve wires and another power source can damage the controller and create a fire hazard.

NOTICE

• Changes or modifications not expressly approved by Rain Bird could void the user’s authority to operate the equipment.
• Use only Rain Bird approved accessory devices. Unapproved devices may damage the controller and void warranty.
• All electrical connections and wiring runs must comply with local building codes. Some local codes require that only a licensed or certified electrician can install power. Only professional personnel should install the controller. Check your local building codes for guidance.
• The battery must be removed from the controller before disposal.
• The leaking batteries should be removed from the device and disposed safely in accordance with local laws.

ISED NOTICE

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

SPECIFICATION

• Electronic disconnection on operation
• Maximum radio-frequency power (for EU and UK): 9,95 dBm
• Operating frequency band: 2 402 – 2 480 MHz

DECLARATION OF CONFORMITY

EU DECLARATION OF CONFORMITY

• Hereby, Rain Bird Corporation declares that the radio equipment type ESPBAT-BT1, ESPBAT-BT2, ESPBAT-BT4, ESPBAT-BT6 are in compliance with Directive 2014/53/EU
• The full text of the EU declaration of conformity is available at the following internet address: www.rainbird.com/RegulatoryCompliance

UK DECLARATION OF CONFORMITY

• Hereby, Rain Bird Corporation declares that the radio equipment type ESPBAT-BT1, ESPBAT-BT2, ESPBAT-BT4, ESPBAT-BT6 are in compliance with Statutory Instrument 2017 No. 1206.
• The full text of the UK declaration of conformity is available at the following internet address: www.rainbird.com/RegulatoryCompliance

DISPOSAL

DISPOSAL OF ELECTRONIC WASTE – FOR EUROPEAN COUNTRIES ONLY

This symbol on the product and/or accompanying documents means that used electrical and electronic equipment (WEEE) should not be mixed with general household waste. For proper treatment, recovery, and recycling, please take this product to designated collection points. Disposing of this product correctly will help save resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.

FCC STATEMENT

SUPPLIER’S DECLARATION OF CONFORMITY

47 CFR § 2.1077 Compliance Information

• Unique identifier: ESPBAT-BT1, ESPBAT-BT2, ESPBAT-BT4, ESPBAT-BT6
• Responsible Party – Rain Bird Corporation, 9491 Ridgehaven Court, Suite C, San Diego, CA 92123, USA, www.rainbird.com

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Rain Bird Corporation

• 6991 East Southpoint Road
• Tucson, AZ 85756, USA
• www.rainbird.com

® Registered trademark of the Rain Bird Corporation
© 2023 Rain Bird Corporation

BATTERY MAINTENANCE

Replace by using four Non-rechargeable, alkaline batteries type LR6 (“AA”).

1. Remove cover
2. Remove batteries
3. Replace with new batteries being careful to install with the correct polarity (+ / -)
4. Replace the cover
5. The batteries removed should be disposed safely in accordance with local laws.

References

• Product Regulatory Compliance | Rain Bird
• Anatel — Agência Nacional de Telecomunicações
• Rain Bird | A Global Irrigation Company
• Rain Bird | A Global Irrigation Company
• Product Regulatory Compliance | Rain Bird

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>