TRENDNET TI-IG290 TI Hardened Industrial Railmount Installation Guide

: June 11, 2024
: TRENDnet

Table of Contents

Before You Start
Quick Reference
Hardware Installation
Declaration of Conformity
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Quick Installation Guide
TI-G290 (v2.XR)

https://www.trendnet.com/gig/1125

Before You Start

Package Contents

TI-G290
Quick Installation Guide
Removable terminal block
DIN-rail mount
Wall mount kit

Minimum Requirements

Existing network
Power Supply (TI-524048 / T1-512048)

Quick Reference

Hardware Installation

The PoE:++ injector can be placed on a desktop, wall, or mounted to a DIN- Rail.

DIN-rail Mounting Instructions

Attach the DIN-Rail mount to the PoE-++ injector.
Position the unit in front of the DIN-Rail and hook the mount bracket over the top of the rail
Rotate the injector downward towards the rail to lock it into place. You will know it is secure when you hear the click.
To remove the unit, pull down to clear the bottom of the DIN-Rail and rotate up, away from the rail.

Wall Mounting Instructions

Attach the wall mount plates to PoE++ injector.
Mount the injector.

Safety Note

Turn off the power before connecting any module or wire. The correct power supply voltage (48 – 56V DC)is listed on the product label. Check the voltage of your power source to make sure that you are using the correct part. Do NOT use voltage greater than 48 – 56V DC, the product label. (TI-1G290 power supply voltage 52-56V DC)
Calculate the maximum possible current in each power wire and common wire. Observe ll electrical codes dictating the maximum current allowable for each wire size. If the current surpasses the maximum ratings, the wiring could overheat, causing Serious damage to your equipment.

Applying Power

Connect the power supply (sold separately) to the included terminal block (as shown below) and secure with the screws.
Note: Polarities must match.
Attach the terminal block to the unit, connect the neutral wire to the ground, and supply power to the power adapter.
Connect a network source and devices to the injector. Check the LEDs to confirm the connections are established. Your installation is completed.

Declaration of Conformity

Manufacturer’s Name and Address
TRENDnet, Inc.
20675 Manhattan Place
Torrance, CA 90501 USA
Zwolsestraat 156 2587 W8
The Hague The Netherlands

Product Information:
Model Number : THG290
Product Name: 90W 2-Port Industrial 2.5G PoE++ Injector
Trade Name: TRENDnet
TRENDnet hereby declare that the product s in compliance with the essential requirements and other relevant provisions under our sole responsibilty.
safty EN 62368-1:2014
EMC Standard
EN 55032:2015
EN 55035: 2017
“This product is herewith confirmed to comply with the Directives
Directives:
EMC Directive 2014/30/6C
RoHS Directive 2015/863/EU
RoHS 3 Directive 2015/863/EU
WEEE Directive 2012/19/EU
REACH Regulation (EC) No. 1907/2006
Low Voltage Directive 2014/35/EC

Person responsible for this declaration
Place of Issue: Torrance, California, USA
Date: December 11,2023
Name: Sonny Su
Tite: VP of Technology

Declaration of Conformity

Manufacturer’s Name and Address
TRENDnet, Inc.
20675 Manhattan Place
Torrance, CA 90501 USA
Authorized Representative:
Office: +44 (0) 1635 887 399
Unit 4 Rivermead Business Park,
Pipers Way, Thatcham, RG19 4EP England
Product Information:
Model Number: TI-IG290
Product Name: SOW 2-Port Industrial 2.5G PoE++ Injector
Trade Name : TRENDnet
TRENDnet hereby declare that the product is in compliance with the essential requirements and other relevant provisions under our sole responsibility.
Safty EN 62368-1:2014
EMC Standard BS EN 58032:2015
BS EN $5035:2017
This product is herewith confirmed to comply with the Directives.
Directives:
Electromagnetic Compatibility Regulations 2016
Electrical Equipment (Safety) Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
The REACH Enforcement Regulations 2008 (as amended)
The Waste Electrical and Electronic Equipment Regulations 2013 (as amended}

Person responsible for this declaration
Place of Issue: Torrance, California, USA
Date: December 11, 2023
Name: Sonny Su
Title: VP of Technology

Certiicaions
This devce complies wih art 15 of the FCC Rules.
Operaton s subject 0 te olowing two condiors

This dvice may notcause harmful interfrence
This dvico must acopt any inerforence recoived.

Inciuding nererence that may cause undesird operaton.

Waste electrical an electronic products must ot be disposed of with household waste.
Please recycle where failtes exist Check with your Local Authorty or Retar for recycling advce.

This equipment has been tested and found to comply with the limis for a Class A igital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecton against hamful intererence when the equipment is operated in a commercial environment. This equipment ‘generates, uses, and can radate rado frequency energy and, if not nstaled and used in accordance with the insruction manual, may cause harmful interference to radio ‘communicatons. Operation of this equipment ina esidential areais likely 10 cause harmful inteference inwhich case the user wil be required to correct the nterference at his own expense
FCC Caution: Any changes or modiication not expressly ‘approved by the party responsible for compliance could void theuser’sauthorty to operato thisequipment.

‘Applies to PoE Products Only: This product s o be connected only to PoE networks without routing to the outside plant.
Note
The Manufacturer is nt respansible for any radio or TV interforence caused by unauthorized modifcations to_this equipment. Such motifcations could void the user’s authorty tooperate the equipment.
Power supply connected caution
The equipment power supply cord shall be connected toa socket-outet with earthing connectio.
If the Optical Transceiver doesn’t ship with the uni, the user manual shal have descripton as below or equivalent: “This product is intended to be use with a UL Listed Optical Transceiverproduc, Rated DCB3V Laser Class ™

Technical Support
Ifyou have any questionsregarding the product instalaion please contact our Technical Support.
Tol free US/Canada: 1-855-373-4741
Regional phone numbers avalable at www.trendnet.com/support

TRENDnet
20675 Manhattan Place
Torrance, CA 90501
usA

Product Warranty Registration
Please take a moment to register your
product niine. Go fo TRENDnet’s website at: www.trendnet.com/register