TILTA WLCT05CH Nucleus Nano II Control Handle Instruction Manual

June 11, 2024
TILTA

TILTA WLCT05CH Nucleus Nano II Control Handle

INSTRUCTION MANUAL

DISCLAIMER

Thank you for purchasing a TILTA product.

Before using this product, please carefully read this document to ensure that the product has been set up correctly. The final interpretation of this document and all related documents for this product belongs to TILTA. For updates, please visit the official website at www.tilta.com for the latest product information. TILTA reserves the right to modify any information in this manual at any time without prior notice and without assuming any responsibility.
By using this product, you are deemed to have carefully read the disclaimer and warnings, understood, agreed, and accepted all the terms and content of this statement. You promise to take full responsibility for the use of this product and any consequences that may arise. You commit to using this product only for legitimate purposes and agree to this term as well as any related regulations, policies, and guidelines set by TILTA.
TILTA is not responsible for any damages, injuries, or legal liabilities caused directly or indirectly by the use of this product. Users should follow all safety guidelines mentioned in this document, including but not limited to those mentioned.

Despite the above provisions, consumer rights are still protected by local laws and regulations and are not affected by this disclaimer.

TILTA is a trademark of Shenzhen TILTA Technology Co., Ltd. and its affiliated companies. Product names, brands, and other trademarks appearing in this document are trademarks or registered trademarks of their respective companies.

PACKING LIST

PACKING LIST

PACKING LIST

INTRODUCING

INTRODUCING

INTRODUCING

FUNCTION

FUNCTION

THE INTERFACE

THE INTERFACE

THE INTERFACE

CONTROL

CONTROL

CONTROL

BASIC OPERATION

BASIC OPERATION

FIRMWARE

YOU CAN USE ANY OF THE FOLLOWING METHODS TO UPDATE THE FIRMWARE.

(METHOD 1. DOWNLOAD FIRMWARE TO UPDATE THE CONTROL HANDLE.]

(1) Download and update the firmware from TILTA’s official website. If you have any installation questions, please reach out to Tilta’s official customer service.
(Tilta official website: wwwtilta.com)

(2) When the control harale is powered off, first press ana hold the [M Butzon] on the cotvoll hanalle (without Ietzing go), and then press ard hold the [Power Button] to access the update page.

(3) Use a data cable to connect the USB=C port of the cont-ol hardle to a comouter, and move the downloaded firmware update to the control handle to complete the update.

(METHOD 2. USE NUCLEUS N Il HAND WHEEL TO UPDATE THE CONTROL HANDLE.)

(1) When the control harcle is powered off, firs: press and hold the [M Button] on the control Fandle (without letting go) and then press ard hold tre [Power Button] to access tre upcate page.

(2) Enter the hand wheel menu at the same time, select [System] – (Firmware Updaze], select [Control Handle], and click [CONFIRM] to start the update. Wren the update prog’ess “eaches 100%, the update will be complezed.

METHOD

* When the hand wheel is connected Lo the Interret, enter [System] –
[FIRMWARE UPDATL] and [SCRVER] window will pop up, lease select the corresponding server according to your locat’on, and then update.

* Check if the device needs updating:
JD If there is a version number with “>” at the bottom of tre device name, that mears the current versior requires a firnware updaze, as pictured below.
CONTROLHA&NSLE

HROKKK $ XXXXAK

  1. If there is no versior number with “>” oelow the device name, thaz mears the currert version does not require firmware updates, as pictured below.
    XXKXXK 9 XKXKXK
  • Before updating the hanale firmware, please ensure that the hand wheel has peen connected to the Internet in advance to update the latest firmware.

+ Before updating, please nake sure that tne battery life of the hand wheel/control handle is no less than 50%, and make sure that no other nearby handles are updating firmware.

¢ Donot olug or unplug the data cable or turr off the hand wheel / control handle  during the update vrocess. I the update fails, perform the update operation again.

  • When uodating wirelessly, multiple cortrol hancles cannot be updated at the same time. Orly one contral handle ca be updated to avoid signal interference.
    + If the update percentage stays between 5% and 6%, or the update speed is too slow, please restart the update operation.

This device complies with Industry Canada licence-exempt R55 standard(s). Operation 05th to the follow nn, two condition& (1) This device may not cause inhrtmence. and (2) This device must actept any Interferon, Including Interference that may cause undeoirec operation of the device. The device has been evaluated to meet general RF exposure requirement. The device can be us. in portable exposure con/tidos wittiest restriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals