Marquardt GmbH IYZGC2 Keyless Start System User Manual
- June 10, 2024
- Marquardt GmbH
Table of Contents
Marquardt GmbH IYZGC2 Keyless Start System
Product Information
Specifications:
- Compliance: Part 15 of FCC Rules
- Operation Conditions: Avoid harmful interference, accept any received interference
- Antenna: Reorient or relocate if needed
- Separation: Increase distance between equipment and receiver
- Power: Connect to an outlet on a different circuit
- Radiation Exposure: Complies with FCC limits for an uncontrolled environment
Product Usage Instructions
Antenna Setup:
Ensure the antenna is properly positioned for optimal reception. If
necessary, reorient or relocate the antenna to improve signal strength.
Equipment Placement:
Place the equipment at an appropriate distance from the receiver to prevent
interference. Increase separation if you experience any operational issues.
Power Connection:
Connect the equipment to an outlet on a different circuit than the receiver
to avoid potential interference. Seek professional help if needed.
Compliance Reminder:
Avoid making any changes or modifications to the equipment that are not
approved by the responsible party to ensure compliance with FCC regulations
and maintain user authority.
FAQ (Frequently Asked Questions)
-
Q: What should I do if I experience interference?
A: Try repositioning the antenna, increasing separation between devices, or connecting to a different power circuit. -
Q: Can I make modifications to the equipment?
A: No, any changes not approved may void your authority to operate the device. Consult a professional if modifications are necessary.
INSTRUCTION
-
The vehicle is equipped with a keyless start system.
-
When the user is within 2m of the vehicle with the Bluetooth key, press the vehicle start button briefly. key 2 to switch the vehicle on; press 2 again to switch the vehicle off;
-
When the vehicle is powered up and the gear is in neutral, press the start button 3 to start the vehicle. Dynamic engine.
-
When the vehicle is parked, press 2 briefly to switch off the engine, then press and hold the start button 2 for more than 2 seconds to switch on the engine.
-
To activate the tap lock, turn the steering handle to the left to the limit position and then the steering handle will be locked. (Square The locking operation can be performed with the handle in any position, but only after it has been turned to the left limit by the (Locked) Key disconnection reminder and automatic power down (depending on configuration)
-
Type 1: When the user’s mobile phone is not registered and bound to the CFMOTO APP, and only carries Bluetooth
-
When the key is used in the car; if the whole car is powered up, if the user carries the Bluetooth key away from the car for more than
-
After about 4~5m, the instrument will pop up a box to remind “Please check if the key is dormant!”. at this time, the instrument will pop up a box reminding “Please check whether the key is dormant! At this time
-
The legal key is no longer within the permissible starting range (approx. 2m) and the vehicle will not be allowed to start for safety reasons.
-
If no response is received when the START switch is operated, the SSB switch can be operated to power down the system.
-
In this case the user re-enters the permitted startup area with the Bluetooth key and the pop-up box will disappear automatically. When the pop-up box appears, if after 60 the key is not in use, it will disappear automatically.
-
The key is still disconnected and the vehicle will be automatically powered down. (This scenario is to prevent the user from parking the car and carrying the key only after switching off the engine without de-energizing)
(The key leaves, resulting in a loss of power to the entire vehicle) -
Type 2: When the user’s mobile phone is not registered and bound to the CFMOTO APP, and the user only carries the Bluetooth key to use the car; when the whole car is powered on, the user
-
The key is placed within the permissible starting range of the vehicle (approx. 2m) and left for more than 5 minutes, in order to increase the battery life of the Bluetooth key will be actively disconnected.
-
Enter the low-power hibernation state. At this point the meter will also pop up a box reminding “Please check if the key is hibernated!” .
(In this case, the user can simply move the key to wake up and automatically restore the connection, and the pop-up box disappears automatically in about 2s.) -
Type 3: When the user’s mobile phone is not registered and bound to the CFMOTO APP, and the user only carries the Bluetooth key to use the vehicle; if the user, during the riding process.
-
The Bluetooth key is accidentally lost, away from the vehicle’s permitted starting zone, when the instrument will pop up a box to remind “Please check if the key is dormant!”. The instrument will pop up to remind “Please check if the key is hibernated!”. At this time, the user needs to
-
Always stop to make sure you still have your keys on you to prevent losing them during the ride.
(In this case, the car will not be switched off and will not be powered down even though a warning box will pop up and it will take more than 60 seconds. That is, as long as the engine is started, the -
That is, as long as the engine is started with the
-
If there is a loss of key, it will not trigger the switching off of the engine and automatic power down. In this case, the user should keep the engine started and confirm that the key is not lost. Once the engine is switched off
-
If there is a loss of key, it will not trigger the switching off of the engine and automatic power down. In this case, the user should keep the engine started and confirm that the key is not lost. Once the engine is switched off
-
If the key is not detected within the permissible starting range, the vehicle will not start again!
-
(Afterwards, if the key is not detected within the permitted starting range, the vehicle will not start again!)
-
Warm Tip:
- Bluetooth key built-in motion sensor, as long as the key is not static, the general instrument will not pop up the box to remind the disconnection.
- If the user’s mobile phone has been registered and bound to CFMOTO APP, and open the digital key function. Under the premise that the Bluetooth of the mobile phone is open, at this time
-
As long as one of the user’s Bluetooth key or mobile phone is within the permissible start range, the meter will not pop up a box to alert the user.
-
Active key battery replacement ( depending on configuration )
-
Active key battery replacement ( depending on configuration )
-
Press button 1 to eject the mechanical key;
-
Using a one-piece screwdriver at the mechanical key ejection port 2, pry off the Bluetooth key cover; Replace the coin cell battery 3 ;
-
Coin Cell Model: CR 2032 (3V)
-
Reinstall the mechanical key and key backplate by snapping the spring 3 into the backplate mounting port 4.
-
Press the mechanical key spring and key backing plate and turn the mechanical key and spring counterclockwise
-
Turn 2 times;
-
Keeping the mechanical key and the key back plate pressed down without dislodging, recombine the Bluetooth key, and ensure successful installation by pressing.
Warm Tip:
When a vehicle is matched with two keys, approaching the vehicle within the same range and time will only
There will be a Bluetooth key effectively connected to the vehicle, and the
user can store the spare key at home stationary Put to avoid loss.
It is not recommended to carry the Bluetooth key with you when the vehicle is
not in use for an extended period. It is possible to place the Blu Dental key
static placement, such as: drawers or desktops and another static environment,
can enhance the key renewal Sailing life.
If the key is left in place for more than 5 minutes, it will go into
hibernation, disconnecting it from the vehicle, such as If it is in the power-
up state, the meter will pop up a window to remind the user, then just move
the key
Recovery; if the key has been sitting for more than 5 minutes before powering
up, wake the key up earlier.
FCC Regulations
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, under Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used by the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.