GAGGENAU VG491211AU Vario Gas Cooktop User Manual

June 9, 2024
Gaggenau

GAGGENAU VG491211AU Vario Gas Cooktop

GAGGENAU VG491211AU Vario Gas Cooktop

INTRDUCTION

VG491211AU
Vario gas cooktop 400 series
Stainless steel
Width 90 cm
Natural gas 10 mbar 

Five multi-ring burners, up to 17 kW Full electronic power level regulation on 12 levels Precise and reproducible flame size Automatic fast ignition, electronic flame monitoring with automatic re-ignition Simmer function for cooking on a very low output level Solid smooth-surface cast iron pan supports Solid stainless steel control knob Precision crafting of 3 mm stainless steel For surface mounting with a visible edge or for flush mounting Can be combined perfectly with other Vario appliances of the 400 series

Cooking zones

  1. multi-ring wok burner (300 W – 5000 W), suitable for pots up to max. ø 32 cm.
  2. two-ring high output burners (160 W – 4000 W), suitable for pots up to max. ø 28 cm. 2 two-ring standard burners (160 W – 2000 W), suitable for pots up to max. ø 24 cm.

Capacity

Control knobs with illuminated ring, cooking zone and output level markings.
One-handed operation.
Full electronic control in 12 output levels for exact power level regulation plus simmer function. Automatic fast ignition.

Features

Simmer function.
Three-part cast iron pan support with flat, continuous pot surface. Brass burner rings.

Safety

Electronic flame monitoring with automatic re-ignition. Residual heat indication. Safety shut-off.

Performance

Depending on the type of installation (surface-mounted or flush-mounted, with or without an appliance cover), the specific location of the cut-out and the knob positions may vary.
The horizontal positioning of the knobs may be aligned with the specific burners.
The drawing “Installation of the control knob” must be observed if the panel is more than 23 mm thick (there must be a recess at the rear).
If combining several Vario appliances of the 400 series, a connection strip VA 420 must be placed between the appliances. Depending on the type of installation, the corresponding connection strip must be provided. The bearing capacity and stability, in the case of thin worktops in particular, must be supported using suitable substructures. Take into account the appliance weight and additional loads. Additional instructions for flush mounting:

Characteristics

Product name/family
gas hob w integrated controls
Built-in / Free-standing
Built-in
Energy input
Gas
Total number of positions that can be used at the same time
5
Min. required niche size for installation (HxWxD)
141 x 887 x 492
Width of the appliance
908
Dimensions
30 x 908 x 520
Dimensions of the packed product (HxWxD)
300 x 700 x 1010
Net weight
30.5
Gross weight
33.3
Residual heat indicator
without
Location of control panel
External control
Basic surface material
brushed stainless steel
Color of surface
Stainless steel, Stainless steel
Color of frame
Stainless steel, Stainless steel
Length electrical supply cord
140
EAN code
4242006262822
Electrical connection rating
Gas connection rating
17000
Fuse protection
2
Voltage
220-240
Frequency
50; 60
Included accessories

Consumption and connection features

Installation is possible in worktops made of stone, synthetics or solid wood. Heat resistance and watertight sealing of the cut edges must be observed. Concerning other materials please consult the worktop manufacturer.
The groove must be continuous and even, so that uniform placing of the appliance on the gasket is ensured. Do not use discontinuous lining.
The joint width may vary due to size tolerances of the combinations and of the worktop cut-out. If installing several appliances in individual cut-outs allow for a division bar of minimum 50 mm between the individual cut-outs.
Special nozzles (for LPG) can be ordered as spare parts. Plan for an electrical connection (the appliance is not operable without power supply). Air intake from above. No intermediate shelf required. Rear panel and wall trims must be heat-resistant and consist of a nonflammable material.
A minimum lateral clearance of at least 300 mm from adjacent heat-sensitive furniture or contact surfaces must be observed or thermal insulation fitted. Installation in a 90 cm wide lower cabinet is required.
The combination with VL 414 is not recommended, since the air extraction from the centre burner cannot be guaranteed due to the distance. With a total connected load of more than 11 kW local regulations concerning room ventilation, room size and combination of extraction or recirculation hoods must be observed. Minimum clearance between gas cooktop(s) with more than 11 kW and ventilation hood 70 cm.
Appliance can be snapped into the worktop from above.
Appliance weight: approx. 31. kg

Connection

Total connected load gas 17.0 KW.
Total connected load electric 15.0 W.
Connecting cable 1.4 m with plug.

VG491211AU
Vario gas cooktop 400 series
Stainless steel
Width 90 cm
Natural gas 10 mbar
2023-01-26

DIMENSIONS

Installation of the control knob; flush installation

Installation of the control knob; surface mounting

A: 3.su
6.S.o..1in combinations with frame1ess induction hobs measurements in mm

View from above

Cross-section

A: 3_5-0J1 6.5-(J·~in combinations with frameless induction hobs
B: Fill with silicone measurements in mm

Longitudinal section

A: 3.5.o.!i 6.5+0·6in combinations with frameless induction hobs
B: Fill with silicone measurements in mmGAGGENAU
Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals