Vibraphone Variable-Speed Driver YVD10 User Manual

: June 8, 2024
: Yamaha

VIBRAPHONE VARIABLE-SPEED DRIVER

YVD10

Owner’s Manual

Make sure to read the “PRECAUTIONS”.

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

This applies only to products distributed by Yamaha Corporation of America.

This applies only to products distributed by Yamaha Corporation of America.

CAN ICES-3 (B)/NMB-3(B)

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Do not open

This product contains no user-serviceable parts. Do not open the units or attempt to disassemble or modify the internal components in any way. If they should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel.
Repairs or part replacement should not be attempted unless instructions are provided in the manual.

Handling

Do not use or store the units in any of the following locations. Doing so can cause fire or electrical shock.
– In places subject to high temperatures (near a heating device or in direct sunlight, etc.).
– In places subject to low temperatures.
– In places where the units may be exposed to moisture (bathroom, on wet floors, etc.) and excessive humidity.
– In places where the units may be exposed to rain.
– In places with excessive dust.
– In places subject to vibrations.
Never insert or remove an electric plug with wet hands. Improper grounding can result in electrical shock.
Never put foreign objects (combustible objects, coins, wire, etc.) or liquids (water, juice, etc.) in the units. Doing so can cause fire or electrical shock.

Power supply/AC adaptor

Only use the voltage specified as correct for the instrument. The required voltage is printed on the name plate of the instrument.
Do not place the power cord of the AC adaptor near heat sources such as heaters or radiators. Also, do not excessively bend or otherwise damage the cord, or place heavy objects on it.
Use the specified AC adaptor only. Using the wrong AC adaptor can result in damage to the units or overheating.
Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
Do not connect the controller unit to an electrical outlet using a multiple-connector. Doing so can result in possibly cause overheating in the outlet.
When removing the electric plug from the unit or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.
Turn off the power switch and remove the electric plug from the outlet when the units are not to be used for extended periods of time, or during electrical storms.

If you notice any abnormality

When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug of the AC adaptor from the outlet. Then have the device inspected by Yamaha service personnel.
– If the AC adapter or power cord becomes damaged.
– If foreign objects or liquids have gotten into a unit.
– If a unit gets wet (rain, etc.).
– If a unit operates abnormally or is broken.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the units or other property. These precautions include, but are not limited to, the following:

Handling

Treating the controller or driver roughly can damage the internal circuit board, etc.
Keep small parts out of the reach of infants. Your children may accidentally swallow them.
Do not place heavy objects on the units, and do not use excessive force on the buttons, switches or connectors.
Never touch the rotating pulleys. Doing so can result in pinching your fingers, etc.

Assembly

Assemble the units in the proper sequence by following the assembly instructions in this manual. Also, make sure to tighten the screws or bolts regularly. Failure to do so might result in damage to the units or even injury.
Use the bolts that comes with the vibraphone.

Transportation and Installation

Do not place the units in an unstable position where it might accidentally fall over.
Before moving the instrument, remove all connected cables, to prevent damage to the cables or injury to anyone who might trip over them.
When setting up the instrument, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the units for a long time, make sure to unplug the power cord from the wall AC outlet.
When moving the instrument, move it gently avoiding shocks and impacts. The instrument is sensitive to shocks and may become damaged.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument.

Always turn the power off when the instrument is not in use.

NOTICE

Do not use the units in locations with poor ventilation.
Parts such as switches, volume control, jacks, are called consumable parts and their function will deteriorate over time. The level of deterioration will vary depending upon the conditions under which the units are used. However, deterioration cannot be completely avoided. When replacing consumable parts, please contact your dealer or qualified Yamaha service personnel.
Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the units.
When cleaning the units, wipe with a soft and dry cloth. Do not use paint thinners, solvents, alcohol, cleaning fluids, or chemical-impregnated wiping cloths.

INFORMATION

The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument.
The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the rear of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft.

Model No. ____

Serial No. _____

Introduction

Thank you for purchasing the Yamaha VIBRAPHONE VARIABLE-SPEED DRIVER YVD10. The VIBRAPHONE VARIABLE-SPEED DRIVER is a motorized drive unit that rotates the fans of the vibraphone. To get full use of this product and enjoy optimal performance, please read this owner’s manual carefully before using the units. After you have read the manual, keep it in a safe and handy place for future reference.

Part Names and Functions

1 POWER switch
Turns the power on (•) and off.

2 Motor speed slider (SLOW 1–6 FAST) Adjusts the fan speed.

3 LED indicator

Lights in green when the power is turned on and flashes while fans arerotating.

Lights in red when an error has occurred. To recover from an error, remove the factors that hinder fan rotation, and then press the 4 START/STOP button.

4 START / STOP button Starts and stops fan rotation.
5 Power jack ()
6 Driver connection terminal
7 AC adaptor (sold separately)

Confirmation of Packing Contents

The shipping package of your YVD10 should contain the parts shown below. Before assembling the instrument, confirm that all parts are included as listed. * If a part is missing, please contact your dealer or qualified Yamaha service personnel.

1 Owner’s Manual (this document) × 1

2 Controller × 1

3 Driver × 1

4 Fan belt × 2

5 Yamaha representative or the authorized distributor list × 1
6 Legal compliance leaflet × 1

Assembly

Attach the controller.
(1) Hook the notch at the upper part of the controller to the screw that protrudes from the lower front of the treble side of the vibraphone, and then (2) secure the hole on the other side of the upper of the controller using the bolt attached to the vibraphone.

2. Attach the driver.

With the pulley to your right side and the connector end of the cable facing you, (1) insert the driver into the driver attachment from below, and then (2) secure it with the cup head square neck bolt and the wing nut.

3. Connect the driver and the controller.

Connect the driver cable to the driver connection terminal on the controller. Also, align the flat shape of the connector of the cable with the mark printed on the controller.

Be careful not to break the pins of the cable.

4. Set the fan belt.

First, wrap the fan belt around the vibraphone (fan) pulley, and then twist and hook the fan belt on the pulley of the driver.

If the distance between pulleys is too wide to fit the belt, or if it is too narrow and the belt slips, first loosen the wing nut and then adjust the tension of the belt. After adjusting the tension, tighten the wing nut firmly.

Order a replacement fan belt (sold separately) using the following number. When ordering, please contact your dealer or qualified Yamaha service personnel. Replace the two fan belts at the same time.

The assembly is now complete.
NOTE
When using for a long time, the fan belt will stretch and the pulley will run idle. If this happens, adjust the tension of the fan belt by slightly lowering the mounting position of the driver unit.

Power Supply

Prepare a separately sold AC adaptor.

1. Connect the DC plug of the AC adaptor to the power jack ( ).

2. Connect the electric plug of the AC adaptor to an outlet.

In order to prevent the DC plug from coming out unintentionally, we recommend wrapping the power cord once around the body leg (as shown) before connecting.

Specifications

 Rated speed: 30–145 RPM
 Power consumption: 3 W
 Operating temperature range: 5–40 degrees Celsius
 Dimensions (W × H × D)
Controller: 172 × 67 × 43 mm
Driver: 92.8 × 65.5 × 183 mm (excluding the cable; approx. 250 mm)
 Weight: 0.6 kg (including the fan belt)
 Included accessories: Fan belt
 Separately sold accessories (May not be available depending on your area): AC adaptor (PA-130: output DC12V 1.0A, PA-130B: output DC12V 0.7A, PA- 150B: output DC12V 1.5A or an equivalent recommended by Yamaha)

The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website and then download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with
general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Manual Development Group
©2019 Yamaha Corporation
Published 12/2019

http://www.yamaha.com.cn

Vibraphone Variable-Speed Driver YVD10 User Manual – Optimized PDF
Vibraphone Variable-Speed Driver YVD10 User Manual – Original PDF