cecotec Fast and Furious 5055 Pro Steam Iron Instruction Manual
- June 3, 2024
- cecotec
Table of Contents
FAST&FURIOUS 5055 PRO
Steam iron Instruction manual
SAFETY INSTRUCTIONS
Read these instructions thoroughly before using the appliance.
Keep this instruction manual for future reference or new users.
Make sure that the mains voltage matches the voltage stated on the rating
label of the appliance and that the outlet is grounded.
Do not leave the iron unattended while hot, connected or on an ironing board.
Place the appliance on a flat, stable and dry surface.
Do not operate the appliance if it has dropped, if it shows visible signs of
damage or if it leaks.
Do not pull the cord to disconnect or move the device. Use the plug instead.
Do not twist, bend, strain, or damage the power cord in any way. Protect it
from sharp edges and heat sources. Do not let it touch hot surfaces. Do not
let the power cord hang over the edge of table or countertop.
Do not immerse the cord, plug, or any non-removable part of the appliance in
water or any other liquid, nor expose the electrical connections to water.
Make sure your hands are dry before handling the plug or switching on the
appliance.
Check the power cord regularly for visible damage. If the cord is damaged, it
must be replaced by the official Technical Support Service of Cecotec, in
order to avoid any type of danger.
Avoid contact with the steam generated by the iron.
The steam temperature is very high and could cause burns and damage. Do not
use chemically descaled water. It is suggested to use distilled water.
The plug must be removed from the power supply before the water tank is
filled.
Always unplug the steam iron from the power supply when filling with water or
emptying and when not in use.
The appliance is not intended to be used by children under the age of 8. It
can be used by children over the age of 8, as long as they are given
continuous supervision.
This appliance is not intended to be used by persons with reduced physical,
sensory, or mental capabilities, or lack of experience or knowledge, unless
they have been given supervision or instruction concerning the use of the
appliance in a safe way by a person responsible for their safety, and
understand the hazards involved.
Supervise young children to make sure that they do not play with the
appliance. Close supervision is necessary when the appliance is being used by
or near children.
PARTS AND COMPONENTS
img 1. (Page 26)
- Function indicator light
- LED display
- Temperature touch button
- Steam regulator
- Spray button
- Steam burst button
- Water inlet cover
- Spray nozzle
- Self-cleaning button
- Soleplate
- Sensor handle
- Power cord
BEFORE USE
Warning: Some parts of the steam iron have been slightly greased and as a
result, the device may slightly smoke when switched on for the first time.
After a short time, this will cease.
Take the product out of the box.
Remove any packaging materials, stickers or protective foil from the
soleplate.
Clean the soleplate with a soft cloth.
OPERATION
Filling the water tank
Note: This appliance has been designed to be used with normal tap water.
Do not use additives.
The addition of other liquids such as perfume, vinegar, starch, condensation
water from tumble dryers or from air conditioning systems or chemicals will
damage the appliance.
- Unplug the iron from the power supply.
- Open the water inlet cover.
- Set the steam regulator to the desired position.
- Fill the water tank. Do not exceed the MAX. mark.
- Close the water inlet cover.
Note: To ensure optimum operating, mix tap water with distilled water. If tap water in your area is very hard, mix tap water with distilled water.
Heating
Plug the device into a power supply.
Set the steam regulator to the “0” position.
The “Self-checking ” function will activate, and the light indicator will
flash for 2 0 seconds approx.
The device will automatically switch to the All textiles mode, and the
corresponding light indicator will light up, indicating that the iron is
heating up.
When the iron is ready to use, the light indicator will remain steady on.
Setting the temperature
Start by ironing the fabrics that require the lowest ironing temperature.
Check the recommended ironing temperature on the label on the garment.
Press the temperature button on the handle repeatedly to change the ironing
temperature and mode.
Press twice each time to switch mode.
The corresponding light indicator will turn on. When the iron is ready to use,
the light indicator will remain steady on.
Setting the steam
The steam regulator is used to adjust the of steam produced when ironing. The
recommended position of the steam regulator for each temperature setting is as
following: img. 2. (Page 26)
Note: For better ironing results, iron the last strokes without steam to
dry the garment.
Steam burst function
This function can be used to remove stubborn creases or to press in a sharp
crease or pleat.
Set the temperature to “max”.
Press the steam burst button repeatedly with intervals of at least 5 seconds.
Vertical steam
Vertical steam can be used to remove creases from hanging clothes, curtains
etc.
Set the temperature to “max”.
Hang article of clothing on a clothes hanger.
Operate the iron in a vertical position at a distance of 10 cm/4 in and press
the steam burst button repeatedly with pauses of at least 5 seconds.
Note: If the Auto shut-off light indicator flashes while ironing in a
vertical position, it means that the handle is not properly gripped, and the
iron will cool down. Grip the handle correctly in such a way that the light
indicator remains lit permanently.
Spray
Spray can be used to remove stubborn creases.
When ironing, press the spray button and water will spray out of the spray
nozzle onto the garment.
Note: Do not use the spray function with silk.
All textiles mode
This mode sets an appropriate temperature, which is suitable for all fabrics
that can be ironed and prevents clothes from becoming damaged due to an
unsuitable temperature being selected.
Note: The All textile mode does not apply to fabrics that cannot be
ironed.
Check the garment care label for details or try ironing on a part of the
fabric not visible.
Press the temperature icon on the handle twice to change the setting.
Auto shut-off function
This function switches off the iron when it is left unattended, increasing
security and saving energy.
While the handle is gripped, the iron heats up. The Auto shut-off light
indicator will remain lit continuously.
When the handle is released, the Auto shut-off function is activated, the iron
stops heating and the Auto shut-off light indicator will flash.
Anti-drip function:
This system controls the water flow to the soleplate at all times. Below a
certain temperature, the anti-drip function cuts off the flow of water and
stops the iron from dripping onto the fabric.
Descaling
The anti-calc function is a permanent system located inside the water tank to
eliminate impurities from the water and to reduce the problems connected with
limescale build- up.
To prolong the efficiency of this system, follow these steps occasionally:
Unplug the iron and allow it to cool down.
Fill 3/4 of the measuring cup with water. Add 1 teaspoon of salt to the water
and fill the water tank with this solution.
Leave the solution in the water tank for 15 minutes, shaking occasionally, and
then empty it.
Fill the water tank a second time with saltwater solution, shaking
occasionally and empty it again after 15 minutes.
Fill the tank with fresh water to rinse and empty.
After ironing
Unplug the iron from the power supply.
Empty the water tank.
Switch the steam regulator clockwise and back again several times (self-
cleaning). Set the steam regulator to the “0” position.
Each time the steam regulator is used, the Self-clean system cleans the
mechanism of scale deposits.
Leave the iron in a vertical position.
Coil the power cord loosely around of the heel of the iron. Store the iron in
an upright position.
CLEANIN AND MAINTENANCE
Turn off, unplug the appliance from the power supply, empty the water tank and
allow it to cool down completely.
If there is any fabric adhered to the soleplate, use a damp cloth with vinegar
to wipe off the soleplate.
Do not use abrasive scouring pads, powders or cleaners to clean the product.
If scale blocks the steam holes, use a toothpick to remove it.
To protect the soleplate while it is stored, place the steam iron in an
upright position on its heel rest. Do not store it close to metal objects.
TECHNICAL SPECIFICATIONS
Product reference: 05570
Product: Fast&Furious 5055 Pro
3100 W, 220-240 V~, 50-60 Hz
IP X0
Made in China | Designed in Spain
DISPOSA OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic Equipment
(WEEE), specifies that old household electrical appliances must not be
disposed of with the normal unsorted municipal waste. Old appliances must be
collected separately, in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human health and the
environment.
The crossed out “wheeled bin” symbol on the product reminds you of your
obligation to dispose of the appliance correctly.
Consumers must contact their local authorities or retailer for information
concerning the correct disposal of old appliances and/or their batteries.
TECHNICAL SUPPORT AND WARRANTY
This product is under warranty for 2 years from the date of purchase, as long
as the proof of purchase is submitted, the product is in perfect physical
condition, and it has been given proper use, as explained in this instruction
manual.
The warranty will not cover the following situations:
The product has been used for purposes other than those intended for it,
misused, beaten, exposed to moisture, immersed in liquid or corrosive
substances, as well as any other fault attributable to the customer.
The product has been disassembled, modified, or repaired by persons, not
authorised by the official Technical Support Service of Cecotec.
Faults deriving from the normal wear and tear of its parts, due to use.
The warranty service covers every manufacturing defects of your appliance for
2 years, based on current legislation, except consumable parts. In the event
of misuse, the warranty will not apply.
If at any moment you detect any problem with your product or have any doubt,
do not hesitate to contact Cecotec Technical Support Service at +34 963 210
728.
| |
---|---|---
SYNTHETIQUES FIBRE SINTETICHE| SOIE/LAINE SETE/LANA| COTON/UN COTONE/LINO
Img. 2
Valencia, Spain
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>