Corsair H100iGTX Extreme Performance Liquid CPU Cooler User Manual

corsair.com

EMAIL: support@corsair.com
FACEBOOK: facebook.com/corsairmemory
BLOG: corsair.com/blog/

FORUM: forum.corsair.com
TWITTER: twitter.com/corsairmemory
H100i GT PAGE: corsair.com/H100iGT
USA and CANADA: 800-205-7657 | INTERNATIONAL: 510-657-8747 | FAX: 510-657-8748

46221 Landing Parkway • Fremont • California • 94538 • USA

© 2014 Corsair Components, Inc. All Rights Reserved. The Corsair logo is a registered trademark, and Hydro Series is a trademark of Corsair in the United States and/or other countries. All other names and products are trademarks and property of their respective owners. Document Number: 49-001307 rev AA

QUICK START GUIDE         H100i GTX

EXTREME PERFORMANCE LIQUID CPU COOLER

Note: Most newer PC cases include a CPU cutout to allow access to the bottom of the motherboard. If your case does not include a cutout, you will need to remove your motherboard from the case before installation.

INTEL

Included Hardware

Highlighted parts for Intel installation only

A x8 LONG FAN SCREWS

B x4 LGA 115X / 1366 STANDOFF

C x4 LGA 2011 STANDOFF

D x4 AMD BLACK STANDOFF

E x4 THUMBSCREWS

F x2 SP120L FANS

G x16 WASHER

H x1 INTEL BACKPLATE

I x1 INTEL MOUNTING BRACKET (PRE-INSTALLED)

J x1 AMD MOUNTING BRACKET

K x8 SHORT SCREWS

L CORSAIR LINK USB CABLE (Included)

Note: The H100i GTX comes with Intel mounting bracket pre-installed on the pump for quick installation.

INTEL

1 Installing the Intel Backplate

• For LGA 115X installation, slide the backplate pins inside (figure 1).
• For LGA 1366 installation, slide the backplate pins outside (figure 1).
• Install the assembled backplate (figure 2).

Note: Intel LGA 2011 does not require backplate installation. Proceed to step 2.

figure 1

figure 2

INTEL

2 Installing the Intel Standoff Screws

• Attach the provided Intel standoff.
• Use (B) for LGA 115X / 1366, or (C) for LGA 2011.
• Tighten all four screws until firmly secure

INTEL

3 Install the Fans and Radiator

Attach the radiator and the fans as shown. For the best cooling performance, we recommend mounting the fans as an air-intake to your PC case.

INTEL

4 Installing the Pump Unit

• Align the bracket and pump over the standoff screws as shown.
• Tighten the thumbs screws until all four corners are firmly secured.

5 Connect Power to the Fans and Pump

• Connect the pump power cable to the CPU_FAN header on your motherboard.
• Connect the fans to the two connectors coming off the pump.

figure 1

figure 2

INTEL

6 Connect Pump to USB Header

Using the included Corsair Link™ USB cable, attach pump unit to a motherboard USB header.

AMD

Included Hardware

Highlighted parts for AMD installation only

A x8 LONG FAN SCREWS

B x4 LGA 115X / 1366 STANDOFF

C x4 LGA 2011 STANDOFF

D x4 AMD BLACK STANDOFF

E x4 THUMBSCREWS

F x2 SP120L FANS

G x16 WASHER

H x1 INTEL BACKPLATE

I x1 INTEL MOUNTING BRACKET (PRE-INSTALLED)

J x1 AMD MOUNTING BRACKET

K x8 SHORT SCREWS

L CORSAIR LINK USB CABLE (Included)

Note: the H100i GTX comes with the INTEL mounting bracket pre-installed on the pump for quick installation.

AMD

1 Installing the AMD Standoff Screws

• Remove the stock AMD top mounting bracket(s) shown. (figure 1)
• Attach the provided AMD standoff. (figure 2)
• Tighten all four screws until firmly secure. (figure 2)
  Note: The stock AMD motherboard backplate is used for AMD installation. AMD standoff are black to differentiate between Intel standoff.

AMD

2 Installing the AMD Mounting Bracket

Note: It is important that the AMD retention bracket be evenly secured on all sides before installation!

• Remove the integrated Intel mounting bracket by pushing on the metal piece, turning 1/8th turn, and pulling away from the copper coldplate (figure 1).
• Install the AMD bracket by aligning the metal teeth, pushing in, turning 1/8th turn the opposite direction, and allowing bracket to secure (figure 2).

AMD

3 Install the Fans and Radiator

Attach the radiator and the fan as shown. For the best cooling performance, we recommend mounting the fans as an air-intake to your PC case.

AMD

4 Installing the Pump Unit

• Align the bracket and pump over the standoff screws as shown.
• Tighten the thumb screws until all four corners are firmly secured.

AMD

5 Connect Power to the Fans and Pump

• Connect the pump power cable to the CPU_FAN header on your motherboard.
• Connect the fans to the two connectors coming off the pump.

Figure 1

Figure 2

AMD

6 Connect Pump to USB Header

Using the included Corsair Link™ USB cable, attach pump unit to a motherboard USB header.

FAQ

1. How do I know the direction of the air flow of the fan?
– An arrow located on the side of the fan indicates the direction of air flow.
2. Can I reuse the pre-applied thermal paste on the H100i GTX for a re- installation?
– Re-installation of the H100i GTX cooler will require you clean off the pre- applied thermal paste and apply an aftermarket paste.

Thank you for purchasing the Corsair Hydro Series H100i GTX Extreme Performance Liquid CPU Cooler.
Please visit: corsair.com to download a detailed user guide or to obtain technical support.
The software can be downloaded from the following location: www.corsair.com/linksw

Corsair H100iGTX Extreme Performance Liquid CPU Cooler User Manual – Download [optimized]
Corsair H100iGTX Extreme Performance Liquid CPU Cooler User Manual – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>