Pidion BIP-5000 Handheld Configuration Manual

June 8, 2024
Pidion

Pidion BIP-5000 Handheld Configuration Manual

Mobile-device

Overview

This document includes configuration information related to features available with the purchase of the Pidion BIP-5000 handheld and its expansion modules. This will also reference the BIP-5000 User Manual.

Model Variations (All with 824 Mhz Processor, 128Mb RAM, and Windows Mobile 6.1 Pro):

  • MG-1: Bluetooth, IrDA, WiFi, 1D Scanner, Camera, GPS
  • MG-2: GPRS, Bluetooth, IrDA, WiFi, 1D Scanner, Camera, GPS
  • MG-4: GPRS, Bluetooth, IrDA, WiFi, 1D Scanner, GPS
  • MG-6: GPRS, Bluetooth, IrDA, WiFi, Camera, GPS

Introduction

Use this document for help on the following options:

  • Installing the Route Manager Shortcut
  • Resetting the Device
  • Wireless GPRS connection
  • GPS Configuration
  • BarCode Scanning Setup

If you are not sure which features are available with your handheld, please contact your reseller or ARS.

Installing Route Manager

This handheld is loaded with the standard, Windows Mobile 6.1 Operating System. Setting up the Route Manager shortcut uses the same method documented in Appendix A of the standard RM Handheld User Guide.

The Handheld Device Type/Program to use in Prepare Data Card and Handheld class is the Standard “ARM WiFi” device option.

NOTE: Please refer to the Handheld User Guide for more instructions on preparing a card and creating the shortcut to RM. You can find the manual on www.ARS247.com or contact ARS Support.

Resetting the Device

Warm Boot

A standard reset can be performed by pressing the tip of the stylus against the “Reset” button located on the back of the handheld, above the battery door:

Resetting-device

Cold Boot/Hard Reset

A “Hard” reset (restores handheld to factory specs, removes all software installed, settings, etc) can be performed by pressing the “Reset” button along with the “telephone” button on the keyboard at the same time. Hold down the telephone button until the Pidion boot screen shows.

GPRS Configuration (Cingular/AT&T)

A wireless GPRS connection is required if you will be using wireless data transfers from a remote location. This type of transfer is typically used with the Advanced Communications and RMLive Modules in RMA.

Note: Not all handhelds include GPRS functionality. If you are not sure which features are available with your handheld, please contact your reseller or ARS.

Follow the steps below to successfully configure your handheld for GPRS transfer.

  1. On the handheld, navigate to Settings > Connections and tap on **Connections.

**

  1. Tap Add a new modem connection.
    Setting-display-tab

  2. Select Cellular Line (GPRS) and tap Next.
    Setting-display-tab NOTE: Enter a unique name for the connection, if desired.

  3. In the Access point name field, enter: wap.cingular (case sensitive).

  4. Enter the following information in the Username and Password fields: User name: WAP@CINGULARGPRS.COM (all caps)
    Password: CINGULAR1 (all caps)
    Domain: Leave blank
    Click Finish to save the connection settings.
    Setting-display-tabYour Pidion BIP-5000 is now configured for wireless GPRS transfers.

  5. Confirm it is ready by confirming WiFi is disabled, then
    launching Internet Explorer and opening a website (such
    as msn.com).

GPS Logging

The Pidion BIP-5000 handheld also has the capability of capturing GPS Coordinates (by stop) or logging the drivers GPS coordinates throughout the day (for review later).

The handhelds doesn’t have any defaults set. But the following options should work: COM Port 8, and the Baud Rate is 19200. You can input these settings by going to Start > Settings > System Tab and then choosing the External GPS option:

Setting-display-tab
Select the Hardware option on the bottom of the screen. Input COM8 and 19200:
Setting-display-tab
These settings will need to be matched in the Handheld Class settings located in Route Manager:
GPS-Logging-tab

BarCode Scanner Setup

The handheld may also has the capability of scanning BarCodes to ease the driver input of products sold to customer, loading the truck, etc.

The following instructions will assist you with setting up the handheld to have the ability to scan BarCodes.

BarCode Scanner Configuration

After starting the program, or confirming its running, we will need to verify the Scanner is set to be used as a “Keyboard Wedge” style scanner. This is checked by:

  1. Go to Start > Settings > System Tab > and click on the “BarCodeSetting” program
    Barcode -setting

  2. Choose the the [+] button next to “Output”
    Barcode -setting-display-tab

  3. Then select the “OutPut: option, and choose the “KeyMsg” option at the bottom of the screen:

  4. Next, select the “Apply” button at the bottom of the screen to save the changes.
    Barcode -setting-display-tab

  5. Select YES to the apply changes prompt:
    Barcode -setting-display-tab

  6. Choose OK on the confirmation prompt:

  7. Select the OK button in the upper right corner to close the BarCode Settings program and complete the setup process:
    Barcode-setting-display-tab

Testing the Scanner

After changing the BarCode scanner software so the Output mode is on Key Msg, we can do a quick test to confirm the scanner is functioning:

  1. Click on the Start Menu > Programs and choose the program for “Notes”:
    Programs-tab

  2. Choose the “New” option on the bottom left of the screen:
    Note-tab

  3. This will then launch us into a blank note entry screen:
    Note-tab

  4. Now, Scan something with a BarCode to see the results (use either of the grey buttons on the sides of the handheld):
    Note-tab Note: This will tell us the actual BarCode read by the handheld.

  5. Once completed, you can choose the “OK” buttons on the top right of the screen to close out of the Notes program. Route Manager Product Configuration

The BarCode scanned in Step 4 above needs to be input in your Route Manager settings for each product on the Handheld tab, in List > Products > Product Charge Codes, within the “Product UPC Code” field.
Product-charge-codes

Pidion BIP-5000 Handheld Configuration Manual – Download [optimized]
Pidion BIP-5000 Handheld Configuration Manual – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals