INDOORCYCLING Pairing of ANT+ Console & RPM transmitter Instruction Manual
- June 7, 2024
- INDOORCYCLING
Table of Contents
INDOORCYCLING Pairing of ANT
TASK DESCRIPTION:
Pairing of ANT+ Console & RPM transmitter.
* _Also refer to owner´s manual (pages 8-10)_**
Applicable for Product:| ANT+ Bike Computer Set
ANT+ Console
|
Applicable for Product Version:| |
Applicable for Product Art. No.:| CO-TK3WL-01
320-00-00001-01
|
Applicable for Product Serial No.:| 312130001 > ……|
The Serial Number information can be found under the battery cover as shown
below.
Please make sure to identify the product prior to performing any repair job.
ANT+ CONSOLE
AFFECTED PARTS
SPARE PART| ICG ARTICLE NUMBER| PART DESCRIPTION| COMMENTS| NO. OF PARTS PER BIKE
(OPTIONAL)
---|---|---|---|---
A| CO-TK3WL-01| ANT+ BIKE COMPUTER SET| Includes:
*ANT+ CONSOLE: 320-00-00001-01
– Owner manual
– Phillips head machine bolt, M5 x 11 x 0,8P , ss304 STAINLESS STEEL, 2x
– Counter sunk Hex. socket bolt, M3 x 8 x0,5P, ss304 STAINLESS STEEL, 4x
– AA batteries, 2x
*ANT+ BIKE MOUNTING & TRANSMITTER KIT:
320-00-00002-01
– Mounting manual
– ANT+ Bike Transmitter
– AAA batteries, 2x
– ANT+ console bracket
– Phillips head machine bolt, M5 x 11 x 0,8P , ss304 STAINLESS STEEL, 2x
– Phillips head machine bolt, M5 x 53 x 0,8P , ss304 STAINLESS STEEL, 1x
-Nut M5 x 0,8P, ss304 STAINLESS STEEL, 1x
-Magnet, 1x
-Rubber 90 x 9 x 0,9mm
-Rubber 90 x 20 x 2,9mm
| 1
B| 320-00-00001-01| ANT+ CONSOLE| Includes:
*ANT+ CONSOLE: 320-00-00001-01
-Owner manual
-Phillips head machine bolt, M5 x 11 x 0,8P , ss304 STAINLESS STEEL, 2x
-Counter sunk Hex. socket bolt, M3 x 8 x 0,5P, ss304 STAINLESS STEEL, 4x
– AA batteries, 2x
| 1
REQUIRED TOOLS:
| TOOLS | SIZE MM | QUANTITY |
|---|---|---|
| Phillips screwdriver | PH 2 | 1 |
Warning!
Please pay attention that the bike is positioned stably and properly secured
while repair work is being performed.
-
Press any button while inserting batteries into the ANT+ console
-
Press “SUN” button to display software version
-
Press “SUN” button again to choose ANT+ RPM pairing mode
-
Press “FLOW” button to start ANT+ RPM pairing
During the pairing process, make sure to:
- Put the console as close as possible to the ANT+ bike transmitter.
- Keep the flywheel in motion by slowly turning the cranks by hand in order to provide a RPM signal.
- Please make sure that the magnet is correctly positioned on the flywheel in order to provide a signal to the transmitter (see picture).
-
As soon as a RPM signal is displayed, pairing of ANT+ RPM transmission is finished
-
KM / MILES settings
- a) Press the “SUN” button to enter KM / MILE setting.
- b) Press “FLOW” button to select between KM or MILES.
- c) Press “SUN” button to confirm your selection and enter gear ratio settings.
-
Gear ratio settings
- Press “FLOW” button to select the gear ratios available:
- 1:3.1 for ICG bikes with V-Belt Drive. (IC3, S & E-Series).
- 1:4.0 for ICG bikes with Timing-Belt Drive.
- 1:4.3 for KRANKcycle.
- Press “SUN” button to confirm your selection and finish the basic settings process.
- Simulate a brief session and test if the ANT+ computer properly reads and displays all the information.
Please note: Heart rate will only be displayed when you use your personal HR chest belt (analog chest belts will be paired automatically; ANT+ chest belts must be paired manually).
-
*Battery exchange and resetting of console in order to resolve any issues to the functioning. see also the owner´s manual (page 14)
a) Remove the batteries of the ANT+ console.
b) Press both buttons on the front of the ANT+ console for at least 10 seconds.
c)** After RESET reinsert the batteries and repeat steps 1-7.
-
*Battery exchange and resetting of cadence transmitter see also the owner´s manual (page 15)
a) Use a screwdriver to remove the cadence transmitter from the bike/KRANKcycle frame.
b) Remove the batteries from the cadence transmitter.
c)** Wait for at least 30 seconds before re-inserting the batteries and repeat steps 1-7.- Test the functionality of the cadence transmitter before re-attaching it to the bike/KRANKcycle frame.
- Test the functionality of the cadence transmitter before re-attaching it to the bike/KRANKcycle frame.
-
End of the operation
a) Use the Phillips screwdriver to secure the batteries cover.
b) Simulate a brief session and test if the ANT+ computer properly reads and displays all the information.
Please note: Heart rate will only be displayed when you are using your personal HR chest belt (analog chest belts will be paired automatically; ANT+ chest belts must be paired manually).- Test the functionality of the ANT+ console before re-attaching it to its support bracket.
- Test the functionality of the ANT+ console before re-attaching it to its support bracket.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>