velleman Vacuum Desoldering Pump With Heater User Manual
- June 7, 2024
- Velleman
Table of Contents
velleman Vacuum Desoldering Pump With Heater
USER MANUAL
1. Introduction
To all residents of the European Union Important environmental information
about this product
This symbol on the device or the package indicates that disposal of the device
after its lifecycle could harm the environment. Do not dispose of the unit (or
batteries) as unsorted municipal waste; it should be taken to a specialized
company for recycling. This device should be returned to your distributor or
to a local recycling service. Respect the local environmental rules. If in
doubt, contact your local waste disposal authorities. Thank you for choosing
Velleman! Please read the manual thoroughly before bringing this device into
service. If the device was damaged in transit, do not install or use it and
contact your dealer.
2. Safety Instructions
This device can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and user maintenance shall not be made by children without supervision.
Read and understand this manual and all safety signs before using this appliance.
Indoor use only. Keep this device away from rain, moisture, splashing, and dripping liquids. Never put objects filled with liquids on top of or close to the device.
Always disconnect mains power when the device is not in use or when servicing
or maintenance activities are performed. Handle the power cord by the plug
only.
Caution! After switching off, leave the power cord plugged in for a
few minutes. When you switch off the unit, the automatic cooling function
blows cooling air through the heater pipe for a short period. This protects
the heater from damage and extends its lifetime. Do not disconnect the mains
plug during this cooling process.
Do not crimp the power cord and protect it against damage. Warning! If the
power cord is damaged, it must be replaced by the manufacturer, its service
agent, or similarly qualified persons in order to avoid any hazard. Make sure
that the available voltage does not exceed the voltage stated in the
specifications of this manual. Plug the power cord into a suitable,
earthed mains outlet. Risk of electroshock when opening the cover.
Touching live wires can cause life-threatening electroshocks. Do not
disassemble or open the housing yourself. Has the device repaired by qualified
personnel? Do not operate the device with wet hands.
Never use the device on live electronic circuits. Make sure power to the
workpiece is cut and capacitors are discharged.
Do not use near inflammable products or in explosive atmospheres. Heat can cause fire to inflammable products even when they are not in sight. Only use in properly ventilated rooms.
Incorrect use may cause a fire.
Do not touch the shafts, tips, or hot air gun as this can cause serious
burns. Keep the tips and hot air away from the body, clothes, or other
flammable material. Do not aim the hot air gun at the eyes. Use gloves and/or
heat-resistant tools to pick up the PCB assembly to prevent burns. Always
return the irons and gun to their stands between uses; always let the device
cool down after use and before storage. Place the device on a level, stable,
and fire-resistant working surface.
WARNING! – This tool must be placed on its stand when not in use; do not leave the tool unattended when switched on.
Do not inhale solder fumes. The vapors that are released during soldering are harmful. Therefore, you shall only use the soldering station in well- ventilated areas or under an exhaust hood (solder fume extractor). Dispose of fume filters and solder residue in accordance with local regulations.
- Use the soldering iron on a heatproof workbench.
- Place the soldering iron in its holder after use.
- Let a hot soldering iron cool down naturally and do not immerse in water.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
-
If you are desoldering a printed circuit board: place the board on a flat, dry surface with the component
side face-up. Make sure the board lies perfectly flat. The heat gun can also melt the solder on nearby components you were not planning to remove. If the board is not perfectly flat, these components can get dislodged from their positions as their solder softens. -
Do not keep the heat gun on and pointed at the components for more than one minute at a time, as the heat may damage the board and components.
4. Operation
- Plug the power cord into a power source.
- Allow the nozzle to warm up for approx. 5 min.
- Press the plunger [1] until you hear a clicking sound.
- Place the tip of the nozzle against the solder you wish to remove.
- When the solder melts, press the button [2] on the handle and
the solder will be absorbed.
5. Cleaning and nozzle replacement
- Turn off the power and wait until the unit has completely cooled before removing the solder waste or replacing the nozzle.
- To clean the unit, push [1] the plunger slightly in the direction of the button and remove it from the grip [2].
- Remove the solder waste around the tip and inside the plunger.
- To replace the nozzle, turn it anticlockwise with a pair of pliers and remove it from the handle.
6. Technical Specifications
inner Ø of tip …………………………………………………………………………………………. 1.8 mm power supply ………………………………………………………………………………….230 V~, 50 Hz power ……………………………………………………………………………………………………… 30 W
Use this device with original accessories only. Velleman NV cannot be held
responsible in the event of damage or injury resulting from (incorrect) use of
this device. For more info concerning this product and the latest version of
this manual, please visit our
websitewww.velleman.eu. The information in this
manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman NV. All worldwide rights
reserved. No part of this manual may be copied, reproduced, translated, or
reduced to any electronic medium or otherwise without the prior written
consent of the copyright holder.
Made in PRC
Imported by Velleman nv Legen
Heirweg 33, 9890 Gavere, Belgium
www.velleman.eu
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>