CORSAIR Companion Touch Screen User Manual
- June 7, 2024
- Corsair
Table of Contents
iCUE NEXUS
Companion Touch Screen
HARDWARE SETUP
iCUE NEXUS connects to PC USB via the standalone base or when attached to a K70 RGB MK.2 or K95 RGB PLATINUM series keyboard via an included bracket.
STANDALONE BASE
1. Connect USB to base
2. Insert iCUE NEXUS
3. Connect base USB to PC
KEYBOARD BRACKET
1. Locate bracket matching keyboard rear center panel
2. Peel off the protective film
3. Attach the bracket to keyboard
4. Slide iCUE NEXUS onto the bracket
5. Connect USB to keyboard
IMPORTANT : If attached to a keyboard, allow 24 hours for the adhesive
tape on the bracket to set before using the touch screen. To remove the
bracket later, turn over the keyboard and insert the included removal tool
(H) into the gap between the bracket and the keyboard from the bottom side,
and then gently press down to lift the bracket until it begins to detach. Hold
the partially detached portion while continuing to lift different areas of the
bracket until it is fully released from the keyboard. Additional brackets are
available at www.corsair.com.
SOFTWARE SETUP
iCUE NEXUS requires the iCUE software. Download iCUE from www.corsair.com/downloads and install on your Windows®PC.
Launch iCUE, click the iCUE NEXUS device tile and then go to the Screens tab to begin designing your own screens with custom graphics and functions.
Swipe left and right on the touch screen to quickly navigate between screens.
NOTE : For more information on advanced programming and product tutorials, visit www.corsair.com/nexus-faq.
GETTING TO KNOW iCUE NEXUS
A — iCUE NEXUS
B — TOUCH SCREEN
C — USB CONNECTOR
D — STANDALONE BASE
E — BASE USB PASSTHROUGH
F — BASE USB CONNECTOR
G — KEYBOARD MOUNTING BRACKETS x 3
H — BRACKET REMOVAL TOOL
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of
the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
CAN ICES-3(B)/NMB-3(B)
iCUE NEXUS
WEB: corsair.com
PHONE: 888-222-4346
SUPPORT: support.corsair.com
BLOG: corsair.com/blog
FORUM: forum.corsair.com
YOUTUBE: youtube.com/corsairhowto
© 2020 CORSAIR MEMORY Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured. 49-002031 AB
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>