amazon 35W LED Barn Light, Dusk Dawn Photocell User Manual
- June 7, 2024
- Amazon
Table of Contents
amazon 35W LED Barn Light, Dusk Dawn Photocell
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following:
CAUTION Risk of electric shock! To prevent risk of electric shock, turn
off the power at the main circuit breaker box before installation.
WARNING Risk of fire! Most dwellings built before 1985 have supply wiring
rated up to 140 °F (60 ºC). Consult a qualified electrician before
installation.
CAUTION Risk of electric shock! This product must be installed in
accordance with the applicable installation cod by a person familiar with the
construction and operation of the product and the hazards involved. Consult a
qualified electrician to ensure correct branch circuit conductor.
CAUTION Risk of eye damage! LEDs emit bright light. Avoid looking
directly into the light source for prolonged periods.
- This product is rated 120 VAC and must be connected to a suitable power source.
- This product is not intended for recessed installation in ceilings, or soffits.
- Do not install any lighting assembly closer than 6″ (15 cm) from any curtain or similar combustible material.
- The product employs non-replaceable LED light sources.
- Contact the municipal building department to learn about applicable local codes, permits and/or inspections.
- This product is intended for use in accordance with the National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part I, in non-hazardous locations, and the Mexican Electrical Code [Instalaciones Eléctricas (utilización), NOM-001-SEDE].
- Do not hang anything on the product.
SAVE THESE INSTRUCTIONS
Intended Use
- This product is intended for residential use only. It is not intended for commercial use.
- This product is intended to be used in dry, damp and wet indoor areas.
- This product is not intended for use with emergency exits.
- No liability will be accepted for damages resulting from improper use or non-compliance with these instructions.
Before First Use
- Check the product for transport damages.
- Remove all the packing materials.
Risk of suffocation! Keep any packaging materials away from children – these materials are a potential source of danger, e.g. suffocation.
Installation Instructions
Risk of of shock! Disconnect power before installation.
WARNING: Take special precautions when working on heights, for example, while using a ladder. Use the right type of ladder and ensure it is structurally sound. Use the ladder in accordance with the manufacturer’s instructions.
NOTICE: This product is intended for wall mount only. It should be mounted in a horizontal position only with the light source pointing down.
Step 1:
Step 2: Drill pilot holes 3/16″ (4.7 mm)
Step 3:
Wiring
Risk of electric shock! To prevent risk of electric shock, turn off the
power at the main circuit breaker box before installation.
WARNING Risk of electric shock! This product must be connected to a
properly grounded electrical system. Never wire the product to a two-wire
system that is not grounded. Contact a qualified electrician for information
with regards to proper grounding methods as required by the local electrical
code in your area.
- Using a flat screwdriver, remove the desired knockout cover on the mounting bracket (B).
- Pass the wires through the mounting bracket (B).
- Use the twist-on wire connectors (C) to join the wires.
- Fasten the mounting bracket (B) to the barn light (A) using 2 bolts (D).
Switch on/off (photocell function)
The built-in photocell (dusk to dawn sensor) automatically switches the
product on at dusk, and switches it off at dawn.
If product cycles on and off, reposition the product to ensure the light is
not reflecting back of any surrounding surfaces.
Cleaning
Risk of electric shock! To prevent electric shock, turn off the power at the main circuit breaker box before cleaning.
- To clean the product, wipe with a soft, slightly moist cloth.
- Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.
FCC – Supplier’s Declaration of Conformity
FCC Compliance Statement
-
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
Canada IC Notice
This Class B digital apparatus complies with Canadian CAN ICES-005(B) / NMB-005(B) standard
Specifications
Model number: FG-03568
Input ratings: 120 V~, 60 Hz, 0.35 A
Rated wattage: 35 W
Color rendering index (CRI): 80
Power factor: 0.9
Color temperature: 5000 K
Luminous flux: 4000 lm
Lifetime: 50,000 hours
Net weight: approx. 2.2 lbs (1 kg)
Dimensions (W x H x D): approx. 9.8 x 6.2 x 3.5″ (25 x 16 x 9.1 cm)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>