ABB Change-over switches Installation Guide
- June 7, 2024
- ABB
Table of Contents
- Installation Instruction, OTM_FC
- Mounting Positions
- Control Circuit
- Manual operation: Local
- Electrical operation: Remote
- Resetting Fuse
- Impulse Control
- Continuous Control
- Locking
- State Information
- Technical Data
- Terminal clamp sets OZX, Bridging bars OMZC
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ABB Change-over switches Installation Guide
Installation Instruction, OTM_FC
OTM30-125-C_
Mounting Positions
Control Circuit
Only an authorised electrician may perform the electrical installation and
maintenance of motorized switch. Do not attempt any installation or
maintenance actions when a motorized switch is connected to the electrical
mains. Before starting work, make sure that the switch is de-energised.
-
Terminal for motor operator voltage supply
-
Control terminal for push buttons
-
Terminal for state information (also used with the automatic control unit)
-
Control terminal for automatic control unit (If used OMD controller)
Do not couple power for the control terminal. See the correct terminal for the power supply.
Manual operation: Local
Electrical operation is prevented when the handle is attached to the switch panel.
Electrical operation: Remote
Never open any covers on the product. There may be dangerous external control voltages inside the motorized switch even if the voltage is turned off.
Never handle control cables when the voltage of the motorized switch or external control circuits are connected.
Exercise sufficient caution when handling the unit.
Automatic Operation
Resetting Fuse
Impulse Control
Continuous Control
If a new command is given before the switch has reached the position of the previous command, the internal protection may operate.
Locking
Prevent Manual and Electrical Operation
Locking Possible at any position. Check position before locking.
State Information
Technical Data
Motor operator, control circuit
|
Value
|
Cabling/Rating
---|---|---
Rated operational voltage U [V]| 110-240 Vac/dc 50-60Hz|
| 24 Vdc|
Operating voltage range| 0.85.. 1.1 x U|
Operating angle| 90° 0-I, I-0, 0-II, II-0; 180° I-0-II|
Operating time| See Table 2|
Protection degree| IP 20, front panel|
Rated impulse withstand voltage Uimp| 4 kV|
Voltage supply| PE N L| 1,5 -2,5mm2
F2| Max. MCB 16A|
Control terminal for the push-buttons| C II I 0| 1,5 -2,5mm2
Maximum cable length| 100 m|
Terminal for state information
Also used with the automatic control unit
| | 1,5mm2
3A AC-1/250V
Common, voltage supply| 1|
Position of change-over switch I| 2|
Position of change-over switch II| 3|
Handle attached or motor operator locked| 4|
SCPD| Max. MCB C2A|
Control terminal for automatic control unit If used OMD_ controller|
| 1,5-2,5mm2
Common, voltage supply from motor operator| 1| 24VDC
Close switch I or open switch II| 2| 24VDC 500mW
Close switch II or open switch I| 3| 24VDC 500mW
Operating temperature| -25… +55 °C|
Transportation and storage temperature| -40… +70 °C|
Altitude| Max. 2000m|
Table 1 : General technical data of motor operators.
Type| Voltage
U e [V]
| Nominal current a)
I n [A]
| Current Inrush a)
____A]
| Operating time a)
I-0, 0-I,
0-II, II-0
[s]
| Operating transfer time a) I-II or II-I
[s]
| OFF-time when operating a) I-II or II-I
[s]
---|---|---|---|---|---|---
__
OTM40…125_C
| 110-240 Vac/dc| 0,2 – 0,5| 1,5 – 3,0| 0,5 – 1,0| 1,2 – 1,5| 0,4 – 0,8
24 Vdc| 0,6| 3,6| 0,6 – 1,3| 1,4 – 2,1| 0,6 – 1,0
Table 2: Specified technical data of motor operators.
Terminal clamp sets OZX, Bridging bars OMZC
OZX_
OMZC_
OTS_
OA_
OTVS0
OTP_
ABB Oy
Low Voltage Switches
P.O Box 622
FI-65101 VAASA, Finland
Telephone +358 10 22 11
Telefax +358 10 22 45708
www.abb.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>