BULLY One Tough Coating Instruction Manual

Materials needed for preparation of truck bed

Put down layers of rubber to any thickness by applying multiple coats for added protection or cushion desired!

Contents: Water-base Paint (Do Not Freeze
Before using this product read the Material Safety Datasheet inside.
NOTE ; This product is a waterborne emulsion and under normal operating conditions presents minimal risk cif fire or explosion. However, proper handling and use practices should he used at all times.

CAUTION : Avoid eye and skin contact. May cause eye and skin irritation.
VOC CONTENT : Material VOC = 0,1 B lbstgal,22 gil Icoa-ong VOC = 0,26 hsigal. 33811, Not regulated by D.O.T. as a hazardous material per title 49 cc is of Federal Regulations. This product does not contain reportable levels of suspected carcinogens per the following sources OSHA, NIP and GAL-OSHA

4 liter (1 gallon) volume coverage

4 ltr covers *approx 260sqft Two coats is recommended for normal truck bed use, 3 or more coats for heavy-duty industrial use “Coverage will vary depending method of application, The coverage listed here is based on rolling and bi, ushing on, Spraying will lay down the thicker coating.
8ft long surface area (including sides, front & tailgate)

For more information and technical assistance info@nutechpaint.net or please visit us at www.bullyliner.com

A. PREPARATION OF TRUCK BED (And any painted metals and fiberglass

surface)

1. The surface must be clean, dry and free of oil & dirt.
2. Wash with soap and rinse with high-pressure nozzle. Then let dry.
3. Use a bowl with acetone and 3M (green) Scotch Brite pad or fine sand paper.
4. Scuff the surface down using the Scotch Brite. Scuff the shine down to a dull matte finish. (There’s no need to sand down to bare metal, light sanding is also recommended).
5. After scuffing, wipe off the sanded white powder with a clean rag & acetone.
   NOTE : Bully Liner will not bond to oil, grease or powder.

Bullyliner is a registered Trademark All rights reserved.

The BULLY QUICK-MASK COVER

This cover is designed to fit all pickup truck sizes. It quickly covers the entire truck leaving only the truck bed opened for spraying.

1. Tape along the top of the side rails accordingly, to determine whether you’re coating the top of rails with the bed or not.
2. Tape a 12” paper along with the cover by the cab. This will prevent excessive overspray buildup on the cover over time.
3. The cover is taped to the side rails and tailgate. The position of your tape determines if you’re spraying the top rails or not.

APPLYING BULLY RUBBER COATING (Using a Paint Brush & Roller)

For best results, use: 1/4” nap microfiber rollers & regular house paint brushes

1. Use undiluted and apply onto the prepared surface. Two coats is recommended for normal truck bed use. Apply unlimited, additional coats for heavy duty use.
2. Putting down your first “tack” coat. A “tack” coat is a light coat of material, gently brush/spray onto the surface to establish good adhesion.
3. Allow the tack coat to dry to the touch before applying additional coats. Depending on temperature and humidity, allow (10 -15) mins in 15c° up
   NOTE : Do Not apply material on too thick per coat or cracking will occur. Allow each coat to dry to the touch before additional coats. Do Not Apply below 10c° temperature

APPLYING BULLY RUBBER COATING (Using Bully Spray System)

For best results, use: BULLY Spray Gun

1. Use undiluted and apply to the prepared surface. Two coats is recommended for normal truck bed use. Apply unlimited, additional coats for heavy-duty use.
2. Putting down your first “tack” coat. A “tack” coat is a light coat of material, gently sprayed onto the surface to establish good adhesion.
3. Allow the tack coat to dry to the touch before applying additional coats. Depending on temperature and humidity, allow (10 -15) mins in 15c° up
NOTE : Do Not apply the material on too thick per coat or cracking will occur. Allow each coat to dry to the touch before additional coats. (Spray at 40 psi using the Bully PP Gun System) Do Not Apply below 10c° temperature

WARNING : KEEP OUT OF REACH OF CHILDREN.

Using a Paint Brush & Roller Properly

1. Start by coating seams and corners of the truck bed using a 2” household paintbrush (not provided). Lightly dab BULLYLINER on rather than brushing it on like paint. Start with a light first coat, being careful not to let BULLYLINER clump or run. Coat tailgate areas in the same manner.
2. Use the 2” brush to apply to corners and areas where the roller won’t reach. Dab the coating on rather than brushing it on. This will give you a more even surface application.  You can later touch up with the brush later on.
3. After you have completed sealing the seams and corners, begin to brush BULLYLINER on the front and side panels of truck bed with a roller.
4. Coating the tailgate using steps 1-3. NOTE: In some applications, it might be helpful to dab BULLYLINER into the lower parts of the floor and tailgate slats with the paintbrush and then roll the BULLYLINER onto the top part. Be careful to watch for clumping. Occasionally stir BULLYLINER to keep it from clumping.
5. After the first coat has been applied to the truck bed and tailgate, allow BULLYLINER to set up (approximately 1-4 hours or when it is no longer tacky). Make sure to apply the second coat within 24 hours of the first coat application. Otherwise, you will need to clean and scuff the first coat prior to applying the second coat. NOTE: TWO COATS  OF BULLY LINER ARE REQUIRED FOR ADEQUATE COVERAGE. (Failure to apply two complete uniform coats will compromise the durability and reduce the life of the bully line truck bed coating.) Use new roller to apply second coat.
6. Repeat the application process for the second coat (steps 1-5).
7. After second coat is dry to the touch, check for any missed spots and touch up.
8. Install tailgate and hardware.
9. The truck bed will be ready for light use in 10-12 hours.
10. Clean all tools using water before BULLYLINER has dried.

Using BULLY HVLP Spray Gun Properly

1. Connect to an air compressor with a pressure of 50-60 PSI. (Higher pressure will provide a smoother finish.) Before starting the job, test spray the gun away from truck bed to become familiar with the spray pattern and coverage.

2. Spray an even coat over the entire surface to be covered in a quick, “S”-shaped motion. Be careful not to apply coat too thickly. Apply a thin, uniform coat of BULLYLINER  to the entire truck bed. Do not apply too thickly to prevent running and drips.

3. Wait about an hour or two, or when surface becomes tacky, then apply a second coat. (Failure to apply two complete uniform coats will compromise the durability and reduce  the longevity of the BULLYLINER truck bed coating.)

4. When surface becomes tacky, spray second coat. Extreme climatic conditions of heat, humidity and cold The first coat should be dry to the touch within one hour and cured in 12-24 hours.

5. The more time between the final coat of BULLYLINER and the topcoat, the quicker BULLYLINER will harden for heavy use. For best adhesion, apply topcoat to BULLYLINER surface within 24 hours.
   NOTE : TWO COATS OF BULLYLINER ARE REQUIRED FOR ADEQUATE COVERAGE.

6. After second coat is dry to the touch, check for any missed spots and touch up.

7. Install tailgate and hardware.

8. The truck bed will be ready for light use in 12-24 hours.

9. Clean all tools using water before BULLYLINER has dried.

Bully Pressure-Pot Spray System

Compressor: 1.6-gallon tank compressor delivers 3.80 CFM at 40psi a 20-gallon compressor 40psi = 6 CFM

1. Connect to an air compressor with a pressure of 50-60 PSI. (Higher pressure will provide a smoother finish.) Before starting the job, test spray the gun away from truck bed to become familiar with the spray pattern and coverage.
2. Spray an even coat over the entire surface to be covered in a quick, “S”-shaped motion. Be careful not to apply coat too thickly. Apply a thin, uniform coat of BULLYLINER  to the entire truck bed. Do not apply too thickly to prevent running and drips.
3. Wait about an hour or two, or when surface becomes tacky, then apply a second coat. (Failure to apply two complete uniform coats will compromise the durability and reduce  the longevity of the BULLYLINER truck bed coating.)

4. When surface becomes tacky, spray second coat. Extreme climatic conditions of heat, humidity and cold The first coat should be dry to the touch within one hour and cured in 12-24 hours.
5. The more time between the final coat of BULLYLINER and the topcoat, the quicker BULLYLINER will harden for heavy use. For best adhesion, apply topcoat to  BULLYLINER surface within 24 hours.
NOTE: TWO COATS OF BULLYLINER ARE REQUIRED FOR ADEQUATE COVERAGE.
6. After second coat is dry to the touch, check for any missed spots and touch up.
7. Install tailgate and hardware.
8. The truck bed will be ready for light use in 10-12 hours.
9. Clean all tools using water before BULLYLINER has dried.

PRECAUTIONS

Avoid contact with skin and eyes. Can cause irritation. AVOID BREATHING VAPOR. USE IN A WELL-VENTILATED AREA. May cause coughing and lung irritation, headache, dizziness, nausea. Harmful or fatal if swallowed. If swallowed, contact the doctor or poison control center. Do not induce vomiting. Give a glass of water. If skin contact occurs, wipe clean with Xylene (Xylol) before BULLYLINER dries. Remove contaminated clothing and wash skin thoroughly with soap and water.
WARNING : KEEP OUT OF REACH OF CHILDREN.

Rude Dog Pty Ltd 27 High Street, Kippa Ring, QLD, Aust, 4021. All rights reserved.

For more information and technical assistance,
please contact us at 7142253688
Email info@nutechpaint.net or
visit us at www.bullyliner.com

Non Toxic • Water Base • Extremely Low VOC • Environmentally Friendly

References

• 📧info@nutechpaint.net
• Home - Bullyliner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>