behringer Professional 6-in-1 Cable Tester User Manual
- June 7, 2024
- Behringer
Table of Contents
User Manual
behringer Professional 6-in-1 Cable Tester
1. Introduction
Congratulations! With the CT100, you have purchased an indispensable tool that enables you to easily check the most common cables used by musicians and sound engineers. Faulty cables are a common cause of failure in live and studio situations. This microprocessor-controlled device was designed to ensure fast, reliable problem location. Various test modes and the included belt clip add to its flexibility.
2. Cable Tester Mode
Move the ON switch to the CABLE TESTER position.
Insert one end of your cable into any OUT jack of the CT100. Connect the other
end of the cable to any IN jack. The LEDs will indicate which input pins are
connected to each output pin. Additionally, the GROUNDED SHIELD LED indicates
whether a XLR OUT jack’s shield is connected to the pin 1/sleeve signal.
2.1 How to test intermittent connections
The following method allows you to detect intermittent connections caused by
wire breaks or faulty solder points. While in CABLE TESTER MODE, press RESET
to store the current cable-wiring display and to clear the INTERMITTENT LEDs.
Move the cable vigorously in all directions and watch the LEDs. Any change in
wiring or break in the signal flow will cause the LED of the corresponding
input pin to light up. The LED will stay lit until RESET is pressed again,
assuring detection of even the shortest breaks in the signal flow. It is a
good idea to repeat the test after resetting the LEDs to double-check the
initial results.
3. Installed Cable Tester Mode
This mode enables you to test cables in fixed installations or situations that don’t allow you to connect both ends of the cable to the CT100.
Hold down the RESET button while moving the ON switch to the CABLE TESTER position. The ON LED will blink to indicate that the CT100 is in INSTALLED CABLE TESTER MODE.
To test a cable for short circuits, connect one end of the cable to the appropriate OUT jack of the CT100. The display works as in CABLE TESTER MODE (see chapter 2). However, it now indicates connections between out pins. If no LEDs light, the cable is free of short circuits.
3.1 Continuity check in Installed
Cable Tester Mode
For a continuity check, connect a shorting jack (a jack in which pins are short-circuited to one another) to the other end of the cable. If there are no breaks in the signal flow, the display will show the corresponding pins as being shorted to each other. If the display indicates no short circuit, there is a break in the signal flow.
- The testing of intermittent connections works exactly as in CABLE TESTER MODE (see chapter 2.1).
- INSTALLED CABLE TESTER MODE will not indicate connections between out and in pins. This is done in CABLE TESTER MODE (see chapter 2).
4. Test Tone Mode
- Move the ON switch to the position TEST TONE.
- Do not use the TEST TONE MODE for MIDI cables!
TEST TONE MODE may be used to check signal flow and to facilitate level adjustments. It routes a test tone to the “+ pin” (pin 2/tip) of all OUT jacks. Use the TEST TONE LEVEL switch to choose between +4 dBu, -10 dBV, or -50 dBV mic level. Please note that this mode is not intended to work as a voltage standard and that battery voltage will affect the test tone output level.
4.1 Selection between 1 kHz and 440 Hz
While in TEST TONE MODE, pressing RESET toggles between 1 kHz and 440 Hz. The
TEST TONE LED indicates the selected frequency:
On = 1 kHz, Off = 440 Hz.
5. Phantom Power Detect
In TEST TONE MODE, pins 2 and 3 are monitored for external DC voltage (commonly supplied for condenser microphones). The PHANTOM LEDs will light if DC voltage above approx. 9 V is detected.
6. Wiring
1/4″, TT, 1/8″ TRS connectors (mono or TS connectors also work)
MIDI connector (2 pins unused)
XLR connectors (pin numbers visible on connectors)
RCA connector
Important Safety Instructions
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water.
-
Clean only with dry cloth.
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions. -
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat. -
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of
the obsolete outlet. -
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
-
Only use attachments/accessories specified by the manufacturer.
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over. -
Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
behringer
CABLE TESTER CT100
Responsible Party Name: Music Tribe Commercial NV Inc.
Address: 5270 Procyon Street,
Las Vegas NV 89118,
United States
Phone Number: +1 702 800 8290
CABLE TESTER CT100
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. -
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that
may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music
Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>