CELESTRON PowerSeeker 60 Instruction Manual

INTRODUCTIION

Congratulations on your purchase and welcome to the Celestron world of amateur astronomy. Some of the terms
and parts described in these instructions may be new to you, so a few commonly used terms you’ll want to be familiar with are defined below. Altazimuth mount – the simplest type of mount, with two motions: altitude (up and down) and azimuth (side-toside). “Mount” refers to the part of the telescope that support the tube, which carries all the telescope’s optics. Altitude lock – allows the telescope tube to be locked into place once a focused image has been set up, by tightening the two screws on the outside of the altazimuth mount. Focal length – the distance from the optical center of the lens to the point where the incoming light rays converge, creating a clear, focused image.
Objective lens – the front lens of the telescope. It gathers incoming light to create a sharply focused image. Refracting telescope – a long, thin tube where light passes in a straight line from the front objective lens directly to the eyepiece at the opposite end of the tube. First, you need to take the time to familiarize yourself with the parts of your PowerSeeker telescope, then assemble it, following the easy instructions provided. Next, read over the operating instructions and become familiar with how
your telescope works, to prepare for hours of viewing enjoyment.

CAUTION: READ THIS SECTION BEFORE USING YOUR TELESCOPE

Your PowerSeeker telescope is designed to give you hours of fun and rewarding observing. However, there are a few things to be aware of before using your telescope that will ensure your safety and protect your equipment. NEVER LOOK DIRECTLY AT THE SUN WITH THE NAKED EYE OR WITH A TELESCOPE. NEVER POINT
YOUR TELESCOPE AT THE SUN UNLESS YOU’RE USING THE PROPER SOLAR FILTER. PERMANENT AND IRREVERSIBLE EYE DAMAGE MAY RESULT. NEVER USE YOUR TELESCOPE TO PROJECT AN IMAGE OF THE SUN ONTO ANY SURFACE, OR USE AN EYEPIECE SOLAR FILTER OR A HERSCHEL WEDGE. INTERNAL HEAT BUILD-UP CAN DAMAGE THE TELESCOPE AND/OR ANY ACCESSORIES THAT MAY BE ATTACHED TO IT.
NEVER LEAVE YOUR TELESCOPE UNSUPERVISED, ESPECIALLY WHEN CHILDREN ARE PRESENT. THIS ALSO HOLDS TRUE FOR ADULTS WHO MAY NOT BE FAMILIAR WITH THE CORRECT OPERATING PROCEDURES FOR YOUR TELESCOPE. ALWAYS COVER THE FINDERSCOPE WHEN USING YOUR TELESCOPE WITH THE CORRECT SOLAR FILTER. ALTHOUGH SMALL IN APERTURE, THIS INSTRUMENT HAS ENOUGH LIGHT GATHERING
POWER TO CAUSE PERMANENT AND IRREVERSIBLE EYE DAMAGE. THE IMAGE PROJECTED BY THE FINDERSCOPE IS HOT ENOUGH TO BURN SKIN OR CLOTHING.

Quiick Settup

THE POWERSEEKER 60 REFRACTOR

The Power Seeker is a classical, two element refracting telescope that comes on an altazimuth mount. This section instructs you on the proper assembly and use of your Power Seeker telescope, which is shipped in one box, containing all the parts you need to assemble it. Unpack and lay out all of the parts in a large, clear area where you’ll have room to work. Keeping track of the parts, use the list below and the telescope diagram to confirm you have, and can identify each part.

a. Altitude slow motion rod assembly
b. Focus Knob
c. Rack and pinion focuser tube
d. 90° diagonal 1¼”
e. Eyepiece 1¼”
f. Finderscope Bracket
g. 5×24 Finderscope
h. Telescope Optical Tube
i. Lens Shade
j. Objective Lens
k. Altitude mount locking screw
l. Altitude slow motion rod locking screw
m. Altazimuth mount
n. Azimuth Lock
o. Tripod Head
p. Accessory tray
q. Three tripod legs, with a collapsible center leg brace

Assemblliing Your Tellescope

To set up the tripod, locate the altazimuth mount (M), the tripod legs (Q) and the tripod bolt pack.

1. Secure the center leg brace to the inside of each tripod leg (Q) using the screws and nuts provided.
2. Connect all three tripod legs to the tripod head (O) with the wing nut and screws as shown in Fig 2a.
3. Extend the inner portion of each of the three tripod legs to the desired height. Tighten the thumb screw on the side of each tripod leg to secure them in place. See Figure 1
4. Attach the accessory tray (P) to the tripod by threading the screw on the bottom of the tray into the hole in the center of the tripod center support bracket. See Figure 3.
5. After all the screws have been hand-tightened, you are ready to attach the telescope tube to the mount. Place the telescope tube inside the altazimuth mount (M) so that the Altitude Slow Motion Rod (A) is on the same side as the locking screw (L) (Figure 2b). Insert the altitude mount locking screws (K) through the mount and thread them into the metal brackets attached to the tube. Before tightening the mount screws, attach the end of the slow motion rod (A) with the knurled adjustment ring to the side of the telescope tube and insert the rod through the eyebolt attached to the altazimuth mount. See Figure 2c.

Attttachiing tthe Accessoriies

Your telescope comes with the following optical accessories:

•  Star Diagonal 1¼”
• 20mm eyepieces 1¼”
• 4mm eyepiece 1¼ “
• 3x Barlow Lens 1¼” and
• 1.5x Erecting eyepiece 1¼”

1. Remove the caps from the focuser (C) and the diagonal (D).
2.  Insert the chrome end of the diagonal into the focuser (Figure 5) and lock into place by tightening the thumb screws on the focuser.
3. Remove caps from the eyepiece and place it into the diagonal (Figure 6). Lock it into place with the thumb screw.
4. The PowerSeeker comes with a 1.5x erecting eyepiece, primarily for daytime terrestrial viewing. This eyepiece corrects the image you see in your telescope, so that it’s both right side up and corrected from left to right. Without this eyepiece, the image you see is reversed from left to right, when using the standard diagonal. To use the erecting eyepiece, remove the diagonal and insert the erecting eyepiece directly into the focuser. Then use a low power eyepiece such as the 20mm, inserting it directly into the erecting eyepiece. See Figure 7.
5. Your telescope also comes with 3x Barlow lens which triples the magnifying power of each eyepiece (see Magnification section of the manual). To use the barlow lens, remove the diagonal and insert the barlow lens directly into the focuser. Then start by using the low power eyepiece such as the 20mm, and insert it either
   directly into the barlow lens or into the diagonal. See Figure 7.

Attttachiing tthe Fiinderscope

1. Remove the two small, silver thumbscrews located at the back of the telescope tube. See Figure 4.
2. Place the finderscope bracket over the two holes in the telescope tube, lining up the holes on the finderscope bracket with those in the telescope tube.
3. Insert the thumbscrews through the finderscope bracket and thread them into the telescope tube.

Alliigniing tthe Fiinderscope

1. Locate a distant daytime object and center it in a low power eyepiece in the main telescope.
2. Look through the finderscope and take notice of the position of the same object.
3. Without moving the main telescope, turn the adjustment thumb screws located around the finderscope bracket until the crosshairs of the finder are centered on the alignment object.

Fiindiing Objjectts

1. Loosen the altitude slow motion rod locking screw (L) and the azimuth lock (N) on the base of altazimuth mount, then move the telescope in the desired direction.
2. Look through the finderscope and pan the telescope until the object appears in the field of view. Once it’s in the field, tighten the altitude and azimuth locks.
3. To center the object in the eyepiece, rotate the fine adjustment ring located on the altitude slow motion rod assembly (A).

Focusiing

1. Once you have found an object in the telescope, turn the focusing knob (B) until the image is sharp.
2. To focus on an object that is nearer than your current target, turn the focusing knob toward the eyepiece (i.e., so that the focusing tube moves away from the front of the telescope). For more distant objects, turn the focusing knob in the opposite direction.
3.  To achieve a truly sharp focus, never look through glass windows or across objects that produce heat waves, such as asphalt parking lots

IImage Oriienttattiion

1. When observing with a diagonal, the image will be right side up, but reversed from left to right.
2. When observing straight through, with the eyepiece inserted directly into the telescope, the image will be inverted. Also, the image in the finderscope is inverted.

Magniiffiicattiion

The magnification (or power) of a telescope varies depending upon the focal length of the eyepiece being used and the focal length of the telescope.
The PowerSeeker telescope has a focal length of 700mm and comes with a 20mm 1¼” eyepiece. To calculate
magnification, use the following formula, in which FL = focal length:

Therefore, if you use the 20mm eyepiece your magnification is 700/20 = 35x. The same formula can be applied to any of your eyepieces. Magnification through any telescope has its limits. These limits are determined by the laws of optics and the nature of the human eye. Most of your viewing will be done in the range of 35x to 120x. Higher powers are used mainly for lunar and sometimes planetary observing where you can greatly enlarge the image and the atmospheric conditions are near perfect. The images at extremely high powers magnify the image, but remember that the contrast will be very low due to the high magnification. For the brightest images with the most contrast, start by using the lower power eyepiece with a smaller image scale. The following magnification levels can be achieved when using the standard eyepiece in conjunction with the 1.5x
erecting eyepiece or 3x Barlow lens:

Eyepiece| Magnification| Mag. with 1.5x Erecting Eyepiece| Mag. with 3x Barlow Lens
---|---|---|---
20mm| 35x| 53x| 105x
4mm| 175x| 263x| 525x

TELESCOPE MAIINTENANCE

With proper care, your telescope should rarely need any maintenance work. To maintain your telescope in the best
possible condition, observe the follow suggestions:

1. When your telescope isn’t in use, replace all lens covers to keep dust and contaminants off the optical surfaces.
2. A small amount of dust on any optical surface isn’t a problem and doesn’t need to be removed. If the dust builds up, then use a can of compressed air and a camels hair brush to remove the dust. To remove fingerprints or other contaminants, use an optical cleaning kit or the Celestron Lens Pen (#93575).
3.  If the inside of the objective lens needs cleaning, it should be done by a professional. Either have your instrument serviced by a telescope repair facility or return it to the factory for servicing.

SPECIIFIICATIIONS

Aperture 60mm
Focal Length 700mm
Focal Ratio f/12
Mounting Altazimuth
Tripod Adjustable Aluminum Tripod

NOTE: Specifications are subject to change without notice.

Opttiionall Accessoriies

Celestron offers a full line of optional accessories for your telescope. Please refer to the Celestron Accessory Catalog
(#93685) for a complete description, or logon to our web site at www.celestron.com. Eyepieces – An assortment of 1¼” eyepieces are available to give you a wide range of
magnifications.

•  OMNI Plössl – Plössl eyepieces have a 4-element lens designed for low-to-high power observing. The Plössls offer razor sharp views across the entire field, even at the edges! In the 1-1/4″ barrel diameter, they are available in the following focal lengths: 4mm, 6mm, 9mm, 12.5mm, 15mm, 20mm, 25mm, 32mm and 40mm.

• Ultima – Ultima is not really a design, but a trade name for our 5-element, wide field eyepieces. In the 1-1/4” barrel diameter, they are available in the following focal lengths: 5mm, 7.5mm, 10mm, 12.5mm, 18mm, 24mm, 30mm, 35mm, and 42mm. These eyepieces are all parfocal. The 35mm Ultima gives the widest possible field of view with a 1-1/4” diagonal.

• Filters, Eyepiece – To enhance your visual observations of solar system objects, Celestron offers a wide range of colored eyepiece filter sets that thread into the 1-1/4″ oculars. Available sets are:

  94119-10 – Orange, Light Blue, ND13%T, Polarizing (#s 21, 80A, 96ND-13,

  Polarizing)

  94119-20 – Deep Yellow, Red, Light Green, ND25% T (#s 12, 25, 56, 96ND-25)

  94119-30 – Light Red, Blue, Green, ND50% T (#s 23A, 38A, 58, 96ND-50)

  94119-40 – Yellow, Deep Yellow, Violet, Pale Blue (#s 8, 15, 47, 82A)

Flashlights – #93588 LED (light emitting diode) flashlights conveniently allow you to read star maps without diminishing your night vision. Both feature adjustable brightness and are small and lightweight, (#93592 is only 6 inches long, and weighs in at a only 3 ounces). Light Pollution Reduction (LPR) Filter (#94126A) – A 1¼” filter that threads into a 1¼” eyepiece, designed to enhance your views of deep-sky astronomical objects when observed from urban areas. The LPR filter selectively reduces the transmission of certain wavelengths of light, specifically those produced by artificial lights. This includes mercury, and high and low pressure sodium vapor lights. Additionally, it blocks unwanted natural light (also known as sky glow).

Sky Maps (#93722) – When learning the night sky, Celestron Sky Maps offer just the guidance you need. The maps show all the constellations and brighter deep- sky objects
and are printed on heavy, moisture-resistant paper for durability. The front cover features a rotating planisphere, indicating when specific constellations are visible.

Solar Filters – Celestron’s (#94131) – AstroSolar® solar filters permit completely safe, direct observation of the sun. This filter, which transmits .00001% of visible light, allows sunspots to be seen as they move across the solar disk. While reducing the intensity of the sun’s visible light, it also blocks 99.999% of invisible infrared light. The solar filter
is made of precision engineered polyester film. A layer of aluminum is vacuum- deposited on the surface of the sheet used to make each filter. This aluminum coating produces a cool, comfortable, pale blue image of the sun. A #21 orange eyepiece filter works well in conjunction with the filter to produce a more naturally colored image of the sun.
Peterson First Guides® – Astronomy (#93728) A simplified field guide to the stars, the planets and the universe featuring full color maps showing the positions of the
stars throughout the year. This useful guide also includes beautiful constellation paintings, photographs, and clear, concise descriptions of stars, the planets, the sun, the moon, comets, black holes, galaxies and more. A full description of all Celestron accessories can be found in the Celestron Accessory Catalog (#93685) or visit our web site at www.celestron.com

CELESTRON TWO YEAR WARRANTY

a. Celestron warrants this telescope to be free from defects in materials and workmanship for two years. Celestron will repair or replace such product or part thereof which, upon inspection by Celestron, is found to be defective in materials or workmanship. As a condition to the obligation of Celestron to repair or replace such product, the product must be returned to Celestron together with proof-of-purchase satisfactory to Celestron.
b. The Proper Return Authorization Number must be obtained from Celestron in advance of return. Call Celestron at 310-328-9560 to receive the number to be displayed on the outside of your shipping container. All returns must be accompanied by a written statement setting forth the name, address, and daytime telephone number of the owner, together with a brief description of any claimed defects. Parts or product for which replacement is made shall become the property of
Celestron. The customer shall be responsible for all costs of transportation and insurance, both to and from the factory of Celestron, and shall be required to prepay such costs.
Celestron shall use reasonable efforts to repair or replace any telescope covered by this warranty within thirty days of receipt. In the event repair or replacement shall require more than thirty days, Celestron shall notify the customer accordingly. Celestron reserves the right to replace any product which has been discontinued from its product line with a new product of comparable value and function. This warranty shall be void and of no force of effect in the event a covered product has been modified in design or function, or subjected to abuse, misuse, mishandling or unauthorized repair. Further, product malfunction or deterioration due to normal wear is not covered by this warranty.
CELESTRON DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WHETHER OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR USE, EXCEPT AS EXPRESSLY SET FORTH HEREIN. THE SOLE OBLIGATION OF CELESTRON UNDER THIS LIMITED WARRANTY SHALL BE TO REPAIR OR REPLACE THE COVERED PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH HEREIN. CELESTRON EXPRESSLY DISCLAIMS ANY LOST PROFITS, GENERAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM BREACH OF ANY WARRANTY, OR ARISING OUT OF THE USE OR INABILITY TO USE ANY CELESTRON PRODUCT. ANY WARRANTIES WHICH ARE IMPLIED AND WHICH CANNOT BE DISCLAIMED SHALL BE LIMITED IN DURATION TO A TERM OF TWO YEARS FROM THE DATE OF ORIGINAL RETAIL PURCHASE. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Celestron reserves the right to modify or discontinue, without prior notice to you, any model or style telescope. If warranty problems arise, or if you need assistance in using your telescope contact:

NOTE: This warranty is valid to U.S.A. and Canadian customers who have purchased this product from an Authorized Celestron
Dealer in the U.S.A. or Canada. Warranty outside the U.S.A. and Canada is valid only to customers who purchased from a Celestron
Distributor or Authorized Celestron Dealer in the specific country and please contact them for any warranty service.

Read More About This Manual & Download PDF:

References

• Celestron - Telescopes, Telescope Accessories, Outdoor and Scientific Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>