TOPSHAK Gallon Wet and Dry Vacuum User Manual

User Manual

TS-VC1

BEFORE USING

1. Please do not use this vacuum cleaner in flammable liquid or gas environment, so as to avoid fire.
2. Please turn the power switch off before pulling out or inserting power cord, so as to avoid the risk of fire or electric shock.
3. Please do not touch the power plug or power supply with a wet hand to avoid electric shock.

WARNING

1. Please do not let the bulk nails and other metal objects remain in the hose and the body extends the tube, otherwise it will damage the hose, filters and so on. Do not inhale mass of hair, spitball and other items, or else easy to plug the hose. If there is blocking phenomenon, please clean up in time.
2. In order to avoid the risk of fire and electric shock, be careful do not allow the body to inhale blade, flame and cement, gypsum powder and other small particles when cleaning.
3. The current above 15A please individually used with an insert board, using a variety of electric appliances on one plug board at the same time may cause a fire.
4. When not in use for a long time, please pull the plug; please do not leave vacuum cleaner unattended while powered on.
5. Please do not let the power cord and vacuum cleaner close to the heating and other heat sources, so as not to deform the body or cause fire; do not use broken power cord and plug, if there is any damage, it should be replaced immediately.
6. Please do not use the vacuum cleaner when the suction inlet and outlet are blocked. Otherwise, it may cause deformation or damage to the body.
7. Please do not let children play with the vacuum cleaner and accessories, so as to prevent accidents.
8. During using, the hose and the body may generate static electricity, please pay attention when using.
9. During using, if there is any abnormal noise or no suction, be sure to shutdown and clean up in time.
10. Please read the instructions carefully before use. Please take out the corresponding parts in the bucket before vacuuming and absorbing water. When inhaling, please place the dust filter. Remove the dust filter when absorbing water.
11. If the power cord is damaged, in order to avoid danger, it must be replaced by the manufacturer, after-sales maintenance department or other professional staff.

-01-

DANGER

1. Non-professionals shall not remove the machine for maintenance.
2. Please do not bend, trample, pull the hose, do not continue to use if the hose is damaged; do not use heavy objects or sharp edge to press the hose.
3. Please do not make the power cord caught in the crack of the door or pull the vacuum cleaner with the power line, so as to prevent damage to the power cord.
4. When the vacuum cleaner stores too much trash, it should be cleaned promptly.
5. Please note the plug when pack up the power cord in order to avoid damage to the surrounding items.
6. During the use of vacuum cleaner, please pay attention to protecting your own safety.

MAINTAIN AND CLEAN

1. In order to prolong the life of vacuum cleaner, it is recommended that every time of continuous use should not exceed 30 minutes.
2. In order not to affect the life of the vacuum cleaner, it is recommended to clean the dust in the vacuum cleaner every time after use.
3. Wipe the surface of the vacuum cleaner with a dry cloth, do not clean it with a wet cloth, so as to prevent it from water-drop entering the vacuum cleaner. Otherwise, it will cause a short circuit and even burn the vacuum cleaner.

DESCRIPTION

1. Hose
2. Latch
3. Dust Barrel
4. Leg
5. Caster Wheel
6. Fur Integrated Brush
7. Suction Seat
8. Plastic Adapter Tube
9. Power Button
10. Handle
11. Dust Filter
12. Sponge Filter
13. Small Flat Suction
14. Small Round Brush
15. Paper Sack

-02-

SPECIFICATION

INSTALLATION

1. Leg and Caster Wheel Installation

(1) Insert the wheel leg into the corresponding position of the plastic barrel and tighten it up with 4 screws.

(2) Insert the pins of the four caster wheels into the corresponding holes in the wheel leg.

-03-

2. Hose Connection with Vacuum Cleaner

Align the two convex points of the hose to the two convex points of the suction seat and tighten it clockwise.

3. Connection with Plastic Adapter Tube

Take two plastic tubes, two ends of the plastic tubes is provided with a big and a small head for distinguishing, insert the small end of one tube into the big end of another tube.

4. Hose Connection with Plastic Tube

Insert the hose into the big end of the tube, screw tightly.

-04-

5. Plastic Tube Connection with Fur Integrated Brush

Insert the small end of the plastic tube into the brush, and tighten up firmly.
Usage: mainly used for sucking the sundries and water stains on carpet, flooring, marble floor, tile floor, etc.

6. Plastic Tube Connection with the Small Round Brush

Insert the small end of the plastic tube into the small round brush, and tighten up firmly.
Usage: mainly used for sucking and sweeping sofa, mattress, curtain and other objects.

7. Plastic Tube Connection with the Small Flat Suction

Insert the small end of the plastic tube into the small flat suction, and tighten up firmly.
Usage: mainly used for sucking and sweeping the furniture edge, frame, books and other irregular objects or corners, etc.

-05-

DRY-WET DUAL-USE

Dry

1. Dust Filter Installation

Put the dust filter in the corresponding position of the dust barrel. (Note: the top of the dust filter where is bulge should be pointing at the suction seat)

2. Paper Sack Installation

Set the holes in the paper sack into the corresponding holes in the suction port.

3. Head and Latch Installation

-06-

Cover the head into the dust barrel (Note: the position of the power button should be aimed at the position of the suction nozzle), and lock up the two latches tightly.

Wet

1. Sponge Filter Installation

(1) Set the sponge filter into the corresponding position of the head.
(2) Install the head on the dust barrel.

CLEAN THE TRASH

(1) Loose the two latches, and remove the head.
(2) Pour the trash into bin.
(3) Cover the head back to the dust barrel after cleaning the trash, and lock up the two latches tightly.

-07-

POWER ON AND OFF

1. Power on: insert the power cord into the socket, switch the button to position “1”, then the vacuum cleaner can be turned on.
2. Power off: switch the button to “0” position, then the vacuum cleaner can be turned off.

TROUBLESHOOTING

2. There is no electricity in the power socket.

3. The power switch of the vacuum cleaner has not been switched on.

| 1. Check that the plug has been wired up properly.

2. The power outlet is out of power. Switch on the vacuum cleaner.

Suction abate| 1. The brush, the hose or the plastic tube may been blocked?

2. The filter is blocked.

3. The fitter bag is filled with dust.

| 1. Remove the blockage in time.

2. Clean the filter.

3. Clean the filter bag.

The body or the exhaust gas overheating| | The heat ejects from body is caused by the heat generated by the conduction of the motor, which is normal. Please rest assured.

-08-

Company: Lotus NL B.V.
Address: Koningin Julianaplein 10, 1e verd, 2595AA, The Hague, Netherlands.
E-mail:peter@lotusnl.com
Tel: +31644168999

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>