RED STONE Electric Radiant Heater Owner’s Manual
- June 7, 2024
- RED STONE
Table of Contents
Redstone Electric Radiant Heater
OWER’S MANUAL
Model No. BY1201
SKU No. 1241595
PLEASE SAVE THESE INSTRUCTIONS
WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.
Thank you for choosing our Electric Radiant Heater. This owner’s manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new heater.
PLEASE SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS,
SAFETY WARNINGS, BEFORE USING THE HEATER
! POTENTIAL FOR ELECTRICAL HAZARD IF NOT
ADHERED TO!
When using electrical appliances, basic precautions should always be followed
to reduce
the risk of fire, electric shock, and injury to persons, including the
following:
- Read ALL instructions before using this unit.
- CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
- This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces.
- Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
- Extreme caution is necessary when any heater is used by or near children or the disabled, or when the heater is left operating and unattended.
- DO NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in any manner.
- This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. NEVER locate a heater where it may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water or other liquids.
- DO NOT touch the control panel or plug with a wet hand.
- DO NOT run cord under carpeting. DO NOT cover the cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
- DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, DO NOT block the air intake or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive, and/or flammable liquids are used or stored. Keep the unit away from heated surfaces and open flames.
- Always plug heaters directly into a wall outlet/receptacle Never use with an extension cord or relocatable power tap (outlet/power strip)
- To avoid fire or shock hazards, plug the unit directly into a 120 V AC electrical outlet.
- To disconnect the heater, turn controls to OFF, then remove the plug from the outlet. Pull firmly on the plug, DO NOT unplug by pulling on the cord.
- Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
- Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by unauthorized dealers may cause hazards.
- Always use on a dry, level surface. Use on floor only.
- DO NOT use outdoors.
- WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device.
- DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user-serviceable parts. Only qualified personnel should perform all servicing.
- Connect to properly grounded outlets only.
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
| Voltage Rating | 120 V (60Hz) |
|---|---|
| Power Consumption | 1500W |
| Unit Size | 16.34 in. (L) x 7.09 in. (W) x 11.42 in. (H) |
| Unit Weight | 5.29 lbs |
SAFETY FEATURES
Overheat Safety Feature
This heater is equipped with a shut-off safety feature. Once the heater is
tipped over, an internal switch will automatically shut the heater off. Once
the heater is restored to an upright position, the heater will reset. To
continue operation, press the power button on the control panel.
Overheat Safety Feature
This heater is equipped with an overheat safety feature. When the heater’s
internal components reach a certain temperature that could cause overheating
and possible fire, the heater will automatically shut off.
WARNING: It is normal for the power cord to feel warm to the touch; however, a loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for damage.
Polarized plugs
This appliance has a polarized plug, (one blade is wider than the other). As a
safety feature to reduce the risk of electrical shock, this plug is intended
to fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature or modify the plugin
anyway. If the plug fits loosely into the AC outlet or if the AC outlet feels
warm do not use that outlet.
PREPARATION
Before beginning the assembly of the product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
PRODUCT DIAGRAM
PANEL DIAGRAM
INSTRUCTIONS FOR ASSEMBLY
To complete assembly, please follow these steps in order:
- Place the heater upside down.
- Ensure Front of Heater and Front of Legs are in the correct position. (Fig. 1)
- Insert Base Feet into notches on the bottom of the heater. Slide toward the front of the heater until secure. (Fig. 2)
- Use 2 screws to secure each leg. Ensure they are tightened securely. (Fig. 3)
NOTICE: When the heat function is used for the first time, a slight odor
may be present.
This is normal and should not occur again unless the heater is not used for an
extended period of time.
- Place the product on a firm, level surface, only in the upright position.
- With the power in the OFF position, plug the unit directly into a 120 V AC electrical outlet
- Turn ON the power switch at the front of the product.
STARTING UNIT AND SELECTING HEAT MODE
| SWITCH ON PANEL | FUNCTION |
|---|---|
| Turn the heater ON by pressing the HEAT ON/OFF button. |
Turn the heater OFF by pressing the HEAT ON/OFF button.
| Press the Mode button to toggle between the heat modes. High Mode (1500
W)/Low Mode (1250W)
| SWITCH ON PANEL | FUNCTION |
|---|---|
| a) To lower temperature, rotate the Knob counter-clockwise toward the “LOW” |
position.
b) To raise the temperature, rotate the knob clockwise toward the “HIGH”
position.
NOTE: After the room has reached the desired temperature, slowly rotate
the temperature knob counter-clockwise until the heater shuts off (you should
hear a faint “click”). By leaving the thermostat at this setting it will
automatically maintain this temperature.
NOTICE: Do not plug the heater into a circuit that is servicing other
electrical needs.
NOTICE: The alarm Indicator will illuminate when the heater has
overheated.If the light is illuminated, immediately turn the ON/OFF Switch to
the “OFF” position, then unplug the unit. Wait for 20-30 minutes for the unit
to cool down, then plug in the unit and reset it according to the INSTRUCTIONS
FOR USE section.
MAINTENANCE
- Turn the POWER OFF.
- Unplug the unit and let it cool completely.
- To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. A mild detergent can be used if necessary.
- After cleaning, dry the unit with a soft cloth.
- Wait until the unit is completely dry before use.
TROUBLESHOOTING
If the heater will not operate, please check the following:
- Check if the power cord is plugged into an electrical outlet. If not, plug in the unit to appropriate outlet.
- Check if the electricity to the outlet is working.
- Ensure power is turned to ON position.
- Make sure the heater is placed on a solid surface.
- See the SAFETY FEATURES section for additional information.
- Overheat protection function may have been triggered. Try to press the power button, if the heater does not turn on, clear any obstructions from the front and rear of the heater that may have caused internal overheating. To restart the heater, unplug it to cool for 5-15minutes, then plugin again. Make sure the obstruction is removed before restarting.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>