VIKING ELECTRONICS VK-PA-IP SIP Multicast Paging Adapter Amplifier User Manual

June 3, 2024
VIKING Electronics

VIKING ELECTRONICS VK-PA-IP SIP Multicast Paging Adapter Amplifier User Manual
VIKING ELECTRONICS VK-PA-IP SIP Multicast Paging Adapter
Amplifier

Overview

SIP Paging Adapter is a IP based paging adapter that can covert analog to SIP. It’s small and portable design with black outlook. The various interfaces (MIC, headset and speaker) make it possible for quickly configure intercom and paging solution. It’s compatible with SIP & ONVIF protocol that can be used in VoIP and security field. It supports two-way intercom communication. Flexible Alarm in and out solutions( GPIO, HTTP URL, and relay out) are widely applied in daily life. The 48KOPUS Audio Codec enables excellent sound quality to make announcement, play background music, security alarm in school, factory and hospital, etc

Overview

Interface Description

Interface Description

① K1 DSS Key| Connect to:

1.  external keys

2.  infrared probe and emergency switch

3.  door sensor and other switch components

---|---
② K2 DSS Key| Connect to:

1.  external keys

2.  infrared probe and emergency switch

3.  door sensor and other switch components

③ Relay NO COM Interface| Control the alarm system on/off
④ IO Onput Interface| Responding to:

1.control the external amplifier power switch 2.the short-circuit input interface

3.  login device security page settings

4.  control the alarm light, electric locks and other equipment

5.  with the adjacent power port connection for external equipment

⑤Microphone Interface| 2.2K Ohm impedance electric condenser microphone is recommended.
⑥ Headset Interface| Speaker audio line signal output impedance 32 Ohm, single ended output voltage 1.2V, used for external headphones or amplifier.
⑦ Speaker Interface| Maximum support 15W speaker.
⑧ Ethernet Interface| WAN port, standard RJ45 interface, 10/ 100M adaptive, support POE input.
⑨ Volume Control Key| This two keys is to adjust the volume of the device’s, bell, phone call and broadcasting, etc.
---|---
⑩ System Reset Key| Press Rest key and hold for 3 seconds, the devices will restart to factory setting.
⑪ Run Indicator| The light is on shows that the device is working well.
⑫ Power Indicator| The light on shows that the power is connected.
⑬ Power Input Interface| 12V ~ 24V 2A input, according to the input voltage

to determine the maximum output power amplifier.

Web Configuration

Web configuration includes complete function setting. When the device and your computer are connected to a same network, please open a browser and type inhttp://192.168.5.200, then log in with defaulted username and password as below. Username: admin
Password: tm1234

Web Configuration

Status

You can check out firmware version, free space and two SIP accounts status of SIP- T20, also can locate the current network information here, like MAC, IP address and gateway etc.

Status

Basic

Date/ Time

There are two update modes for time:NTP/ local time, choose one and set the timezones, NTP sever and interval can choose default setting, then save the configuration.

Basic

Network

When you choose DHCP and save it, IP address will be created automatically by a DHCP server, then you need to login again with the new IP address on browser:
192.168.5.XXX. Status IP address: it is a default IP and will not be e changed as following.

Network

ONVIF

Select Enable ONVIF, then the device be searched by ONVIF VMS. Default user name: admin, password:tm1234.

ONVIF

SIP Account

Each device has two SIP accounts, put SIP extension messages into the blanks andsave the configuration, then you can check if it registers successfully or not on status.

Expire time Set the expire time of registered account information
Ringing tone 5 system ringtones and 10 users upload media files
Auto Answer answer immediately and answer delay when a calling incomes

SIP Account

Audio

ACE(acoustic echo canceling): to make a perfect sound quality. Mic / out volume: adjust mic and output volume at 0-100. Jitter buffer: to make the audio more stable.

Amp auto off: It’s set defaulted as ON, then there is no noise when not broadcasting. Code setting: four audio codes to compatible with major audio sources.

Audio

Media File

There are five system ringtones, and you can upload 10 media files as customers’ demands: music, announcement, bells, etc.

Alarm

We can set 2 DSS keys and 2 SIP accounts to realize alarm function, to ready the combination with alarm system.

Alarm

DSS Key Setting

Enable the file, you select a action type(start/ stop), play file and cycle mode, savethe configuration, then press buttonK1 & K2, the bell will ring/close.

DSS Key Setting

SIP enable: choose a SIP account you register, SIP action: call out/hang up, youcanput the SIP number, eg: 8112,make sure it’s the extensions which connected tothesame IP sever with SIP account 1&2.
If you select call out, and press K1/K2 button, then extension 8112 will receive a call.

DSS Key Setting

  • Enable URL: put the HTTP URL, after pressed K1/K2, the URL will be working.
  • Output enable: turn on/off the output, press K1/K2, the output succeeds.
  • Relay enable: turn on/off the output, press K1/K2, the relay succeed.
    DSS Key Setting

HTTP URL

User can control the alarm by HTTP URL:

  1. Enable the selection;
  2. Open any browser you have in computer;
  3. Put the URL as the following examples, enter it.

HTTP URL

Schedule

This function is widely use in school, factory and office projects. Making a regular bell, announcement and alarm. Enable the schedule, you can name the schedule. then setting it step by step.

Schedule

RTP Multicast IP

There are 10 RTP addresses can be received for each device, please note that: port numbers do not use continuous numbers when setting the same RTP addresses. Usediscontinuous numbers. eg:
239.255.1.2:8000,239.255.0.1:8001,239.255.0.1:8002(×)239.255.0.1:8000,239.255.0.1:8002,239.255.0.1:8004 (√)

  • Multicast address range: 224.0.0.0-239.255.255.
  • Ports range: 1024-65536
  • Use IP Tool, Audio manager and PA System to make RTP multicast.

RTP Multicast IP

Firewall

This function is use to protect your network safety. You can edit the firewall automatic defence rules as you need as follows.

Firewall

System

Upgrade

When reboot and reset the system, system will turn to original setting, and youneed to re-login the web page. How to upgrade SIP-T20 firmware version in web interface?

  1. Select the latest version firmware T20-xxx-bin.
  2. Click upgrade to refresh, it would require about 20s.
  3. Re-login the web interface, latest version has upgraded.

Security

Set a new user name and password as you need, save the configuration and restart login.

Security

IPTool Configuration

Apart from Web configuration, IPTool is the other option that configure quickly basicinformation such as SIP account setting, volume setting, RTP Multicast setting, upgrade. Please follow below steps.

  1. Download IPTool(contact sales or support to get one).
  2. Enter IPTool, scan local network, the device will appear and then start setting.

IPTool Configuration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals