WALI Single Mount with Laptop Tray Installation Guide
- June 7, 2024
- ALI
Table of Contents
WALI Single Mount with Laptop Tray Installation Guide
WARNING
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect
assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER .
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
-
Pole a (x1)
-
C-Clamp b (x1)
-
C-Clamp Brace c (x1)
-
Swivel Arms d (x1)
-
VESA Plate e (x2)
-
M5x14 Bolt f (x3)
-
M8x12 Bolt g (x2)
-
Nut h (x2)
-
M10 Bolt i (x1)
-
Support Plate j (x1)
-
M10 Washer k (x1)
-
Spring Washer l (x1)
-
Grommet Base Plate m (x1)
-
Wire Clip n1 (x2)
-
Wire Clip n2 (x3)
-
Allen Key o (x1)
-
Wrench p (x1)
-
M4x12 Bolt q (x8)
-
M4x30 Bolt r (x8)
-
M4 Spacer s (x8)
-
Laptop Tray t (x1)
-
M4x10 Bolt u (x4)
-
M4 Nut v (x4)
-
Washer w (x4)
-
Anti-skid Pad x (x4)
Option A : Clamp Installation
-
Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and tighten with Allen Key 3mm o .
-
Select the preferred height according to your desk thickness. Connect C-Clamp b to C-Clamp Brace c using M8x12 Bolt g and tighten with Allen Key 5mm o . Rotate the hand knob clockwise to fasten for stability.
Option B : Grommet Base Installation
Place Pole a onto Grommet Base Plate m . Connect them from the bottom using M5x14 Bolt and tighten with Allen Key 3mm o.
2a. Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount. Position the Pole a on the mounting surface and secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the Bolt using the provided Wrench
2b. Self-drilled Grommet Hole Installation
Mark the position of the hole on your mounting surface. Drill a 3/8″(10mm) diameter hole at the marked position through the mounting surface. Position the Pole a on the mounting surface and secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the Bolt using the provided Wrench
Put the Wire Clip n1 and Swivel Arms d through the Pole a , adjust the preferred height and tighten using Allen Key 6mm o . Attach the Wire Clips n1 to the Swivel Arms d .
Option A : Laptop Tray Installation
Using M4 X 10 Bolt u , M4 Nut v , and Washer to attach the VESA Plate e to the
laptop tray t and tighten with a screwdriver. Put the Anti-skid Pad on the
designated position on the tray. (Screwdriver not included)
Option B : Monitor Mount Installation
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)
Select Monitor Screws
Select Spacers ( if needed )
Flat Back Monitor
Curved or Recessed Back Monitor
Put the assembled laptop tray and TV/Monitor onto the Swivel Arms d . Tighten the VESA Plate e with Nut h for stability.
Guide the cable through the Wire Clips ( n1, n2 ) and store the Allen Keys o in the Wire Clip n1 . Manually swivel, tilt, and rotate the monitor laptop tray for the best viewing angle. Adjust the tilt angle using Allen Key 5mm
Notice: Please make sure the security nut is installed before you rotate the monitor. For safety, please remove your laptop when making adjustments.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>