Ali Express YXE-512SE 192 Wireless Console User Manual

Ali Express YXE-512SE 192 Wireless Console User Manual

Please read this instructions carefully before use

INTRODUCTION

Thank you for purchasing the DMX MASTER 1921/1922 The DMX MASTER is a standard universalDMX512controller, controlling Up to 192 DMX channels. Following are it’smain features:

A.)12fixtures of up to 16 channels.
B.)30 banks of8 sceneseach for a total 240 scenes.
C.)6 chased each up to 240 scenes.
D.)8 faders adjust the DMX output levelfrom 0～255.
E.)2 faders control chase speed andfadetime.
F.)Built in Microphone.
G.)Blackout
H.)Specification:
Power input:DC9~12V ,1a
DMX Output: (3 pin XLR)*2
Size:36-21-10cm

FUNCTIONS

Front Control Panel

1. Scanners: To select any or all of 12fixtures.
2. Scenes: to store or run scenes.
3. Page Select: To select page Afor channel 1 to 8, or page B for channel 9 to 16.( A=Red indicator light, B=Yellow indicator light)
4. LC.D Display:4- digit showing values and settings chosen.
5. Bank(up ▲ and down ▼ ): 30 banks are available for selecting.
6. Chases: To select1~6 chases.
7. Blackout: Disables all channel outputs.
8. Program: to activate the program mode. Display links when activated.
9. Auto/Del: to select Auto run in chase mode or delete scenes and/or chases.
10. Music/bank Copy: To trigger sound activation in Chase mode or to copy a bank of scenes from one to another in program mode.
11. Tap SYNC/Display: In Auto Chase mode used to change the rate of chase and in program mode change LCD display value.
12. Fade Time Slider: To adjust the Fade Time. Fade Time is the time it takes the DMX Master to completely change from one scene to another.
13. Speed Slider: To adjust the rate of chase speed in Auto Mode.
14. Speed Slider: To adjust the output level from 0~255 or the intensity from 0%~100% of each channel.
15. Light control push rod.

Rear Control Panel●

16. MASW: Power Switch
17. WLSS: Wireless Switch
18. DMX512: input and output
19. Power supply: 9-12v 1a
20. USB charging: Mobile power supply port
21. PL: Wireless signal indicator light and ID grouping indicator light
22. ID: ID grouping button
23. WL: 2.4G antenna

SCANNERS list

DMX512 Addressing

●Scene Programming

1. Press and hold Program button for three seconds to activate program mode.The LCD next to “program”blinks, indicating the program has been started.

2. Select a fixture to program, by pressing any or all Scanner buttons 1 to 12.

3. Adjust the faders to the desired output level for all channels(i.e. Color, Gobo, Pan, Tilt, etc.)of selected fixture or fixtures. Press Page Select A/B if the fixture has more than8 channels.When selecting from Page A to B, you have to move sliders to activate channels.

4. If you have set the fixture to your liking and wish to program another fixture,press the Scanner button you have finished adjusting. This will hold the fixture in its final configuration. Select another fixtur e/s by
   pressing the target Scanner button and proceed to adjust the faders To achieve the settings you desire.

5. Repeat steps 2 and 3 until you have set the fixtures the way youlike

6. When entire scene is set to your liking press and release the MIDI/Add button.

7. Select the desired bank to store scene using the Up and Down Bank select button. There are 30 banks you can store upto 8 scenes perbank for a total of 240 scenes.

8. Then press a Scene Button 1~8 to store the scene.AllLEDs blink 3 times. The LCD will display the bank and scene where scene was stored.

9. Repeat steps 2~8 to record your desired scenes.
   You cancopy the settings from one scanner button to another in case you want to add more fixtures to your show. Just press and hold the scanner button you want to copy, then press the scanner button you want to copy To11.)to exit programming mode press and hold the Program button for 3 seconds. (When you exit programming, the Blackout Led is on, press Blackout button to de-function blackout.)

● Scene Edition

This function allows you to make changes in a previous programmed scene.

1. Press the program button for three seconds to enter program mode
2. Use the Bank UP and Down button to selectthe bank that stores the scene you wish to edit.
3. Select the scene you wantto edit by pressing its Scene button.
4. Use the faders to make your desired adjustments.
5. Press the MIDI/Add buttonthen followed by the Scene button that corresponds to the scene you editing to store it to memory.
   Note: You must select the same scene you selected earlier otherwise you may accidentally record over an existing scene.

● Scene Copy

This allows you to copy the settings of one scene to another.

1. Press the Program button for three seconds to enter programmode.
2. Use the Bank Button up and Down to locate the bank that stores the scene to copy.
3. Select desired Scene you want to copy by pressing the Scenebutton.
4. Use the Bank buttons Up and Down to select the bank where you want to store the copies scene
5. Press MIDI/Add followed bythe Scene Buttonwhere you wantto copyto

● Delete Scene

This functionwill reset all DMX channels incorporated with a scene to 0.

1. Select the desired scene to delete.
2. While pressing and holding Auto/Del, pressthe Scene button(1 to 8) you want to delete.

● EraseAll Scenes

This will erase all scenes in all banks. All scenes are reset to 0.

1. Press and hold down Program and BankDown buttons while turning power off.
2. Re- connect the power, all scenes should be erased.

● Copy Bank

This fundion enables you to copy the settings of one bank to another bank.

1. Press and hold the Program Button for three seconds to activate the programming mode.
2. Selectthe bank you want to copy.
3. Press and release the MDI/Add button.
4. Select the bank into which you want to copyto.
5. Press the Music/Bank-Copy button. TheLCD display will flash shortly to indicate the copyhas been finished.

● Delete a Bank

1. Press and hold the Program Button for three seconds to activate the programming mode.
2. Selectthe bank to be deleted. Press the Auto/Del and Music/Bank-Copy at the same time to delete the Bank.TheLCD will flash to indicate the function completion.

● Chase Programming

You have to program scenes before you can program chases.

1. Press and hold the program button for 3 seconds to enter programming mode.
2. Choose and chase(1~6) to be programmed.
3. Select the desired Scene form anybank. Scenes arerun in the order that they are programmed into the chase.
4. Press the MIDI/Add button, all theLED will flash 3 times.
5. Repeat steps 3 and4 as many as you want .You can record up to 240 scenes into one chase.
6. Press and holdthe program Button for 3 seconds to exitprogramming mode.

● Copy a Bank to a Chase

1. Press and hold the Program Buttonfor three seconds to enter the programming mode.
2. Select the bank of scenes you wishto copy.
3. Select the chase to which you want to copy the bank of scenes.
4. Press Music/Bank-Copy, and MIDI/Add simultaneously. The scenes of the bank are copied to the Chase.
5. Press and holdthe Program Buttonfor three seconds to exitprogramming mode.

● EDITTING CHASES
Adding a Step to a Chase

6. Press and holdProgram Button for three seconds to enter theprogramming mode.
7. Select the chase 1~6 to which you wish to add a step.

PressTAP SYNC/DISPLAY and the LCD show the sceneand bank. This is

1. the bank containing the scene you wish to add.
2. Press TAP SYNC/Display again and LCD show the Chase that you have selected.
3. Use the Up and Down buttons to scroll through the chaseto reach you have selected.
4. Press MIDI/Add, the LCD will read one step number higher. ●
5. Press the scene button you wish to add.
6. Press MIDI/Add againto add new step.
7. Press and hold the program button for three seconds to exit the programming mode.

● Deleting a Step in a Chase

1. Press and hold the Program Button for three seconds to enter the programming mode.
2. Select the chase 1 to 6 from which you wish to delete a step.
3. Press TASP SYNC/Display and the LCD shows the Chase that have selected
4. Use the Up/Down buttons to scroll through the chase to reach the step you wish to delete.
5. Press Auto /Del and the scene will be deleted.
6. Press and hold the program button for three seconds to exit the programming mode.

Delete Chases (All Scenes are still available)

1. Press and hold the program button for three seconds.

2. Press the chase button that you want to delete.

3. Press and hold the Auto/Del button and then press and hold the Chase button of the have to be deleted. The LEDs will flash three times.

4. Release both buttons and the chasewill be deleted.
   Delete All Chases (all scenes are stillavailable

5. Press and hold down the Bank Down and Auto/Delbuttons while turning power off.

6. Re-connect the power, all chases should be deleted..

● RUNNING SCENES
● Manual Run Scenes

1. When the power is first turned on, the unit is in manual scene mode.
2. If in Program mode, press and hold the Program button forthree seconds and the program LED will go out. The controller is now in Manual mode.
3. Be sure that the Auto & Music buttons’LEDs are off. ■
4. Select the Bank, using the Up and Down B ank buttons that stores the scenes you wish to run.
5. Press the Scene Button to run the scenes you selected.

● Auto Run Scenes

This function will run a blank of programmed scenes in a sequential loop.

1. Press Auto/Del once to activate the Auto Run mode.

2. Use the Up and Down Bank buttons to select a bank of scenes to run.

3. Now you can use the Speed andFade Slidersto adjust the scenes to you liking.
   The fade setting shouldnever be slowerthan the speed setting or the sceneswillnot be completed.

4. You can change banks on the fly bypressing the Up and Down Bank buttons.

● Music Run Scenes

1. Press the Music/Bank-Copy button and the corresponding indicator light will come on in LCD.
2. Select desired bank that storesthe scenes you wish to chase by suing Up or Down buttons or you can control via MIDI signals.
3. Press Music/Bank-copy once more to exit.

● MIDI Run Scenes

1. Select bank to run scenes using MIDI whenever it is in Manual Auto or Music Run mode.

● RUNNING CHASES
● Manual Runchases

This function will enable you to manually step through a selected chase.

1. Press and hold the program button for three seconds to enter programming mode.
2. Start a chase by selecting one of the six Chase buttons.
3. Press the TAPSYNC button. Each time you press the button, you will step through the chase.
4. Use Bank select buttons to scroll through the chases.
   Press and hold the Program button for three seconds to exit programming mode.

● Auto Run Chases

1. Press any or all ofthe six Chase button to select the desired chase.
2. Press and release the Auto/Del button. The corresponding LED will flash.
3. Adjust the Speed and Fade Time to your desired settings. The Chase will run according to your settings.
4. You can override the speed and fade time by tapping the TAPSYNC/D isplay button three times. Then the chase will run based on the time interval of your taps.
   Note: A.) Never adjust Fade time slower than the Speed setting otherwise your scenes will not be completed before a new step is sent!
   B.) If you wish to include all the chases,press Auto/ Del button before selecting chase

● Music Run Chases

1. Press one of the six chase buttons to select your desired chase.
2. Press and release the Music/Bank-Copy button.
3. The corresponding LED will flash in the LCD.
4. Your chase will now run to the sound.
   Note: When you exit a chase by pressing the Chase button, the controller will automatically run the scenes that are in the last bank accessed.To stop the movement of the lights either use the Blackout button or press Music if in music mode or the Auto button.

● Chases 120 to 125 1 to 6 chases
BLACKOUT 126 BL ACKOUT
The DMX Master you might have to transpose your keyboard to find the proper notes.

1.TROUBLESHOOTING
A.)Colors don’t respond when faders are moved.
Makesure address is correct .If the XRL cable is more than 30 meters, checkif it is terminated properly.
B.)Mirrors don’t respond when faders are moved.
Makesure address is correct. Make sure speed is adjusted, if available, for faster movement.Not all fixtures have speed adjustment. If the XRL cableis more than 30 meters, check if it is terminated properly.
C.) Scenes don’t run after record them
Makesure to press Add button before pressing Scene button. Be sure you are in the correct Bank that has scenes recorded.
D.)scenes don’t run correctly as recorded them
Madesure all fixtures were recorded. Make sure you arein the correct bank that has scenes recorded.If the XRL cable is more than 30 meters, checkif it is terminated
properly.
E.)Chase don’t run after record them
Makesure to press Add button after pressing Scene button.LED should blink after pressing Add button.
Be sure you are in the correct chase that has stepsrecorded. If in Auto Mode, did you adjust speed after selecting Auto?Is Fade time to long for speed selected? If the XRL cable is more than30 meters, check if it is terminated properly.

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines. This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>