GLACE BAY Snooker ICE Machine User Manual
- June 7, 2024
- GLACE BAY Snooker
Table of Contents
ICE MACHINES
INSTALLATION, OPERATION AND
USER MANUAL
Preface
Before installing, operating, or maintaining this product, carefully read the
entire contents of this instruction manual.
Become familiar with the equipment’s function and safety precautions prior to
operating or servicing the unit.
Always use tools that are in good condition when servicing the unit.
Always read and follow any safety placards that are located on the unit. These
placards contain specific safety information regarding refrigerant and
electrical voltage hazards.
Always follow local environmental regulations when working with refrigerants.
Fill in the information listed below and file it away for future reference.
Model Number:
Serial Number
Purchased Date:
Install Date:
© Glace Bay Enterprises Inc, all rights reserved
CHAPTER 1 – GENERAL INFORMATION
1.1 Introduction
This manual has been compiled as a guide to the installation, operation, and maintenance of your new equipment. Please take the time to read it and familiarize yourself with your equipment and its operation.
A serialized data tag is permanently attached to the unit. (See Figure 1 for
example of data tag).
The model and serial number should be noted on the second page of this manual,
in the spaces provided. If parts or service is ever needed for your unit, this
information will be required to verify warranty status and to properly
identify any parts that may be needed.
1.2 Scope of the Manual
This technical manual provides information for installation, operating, preventative maintenance, and service instructions, including applicable drawings and figures of the equipment.
CHAPTER 2 – INSTALLATION
2.1 Unpacking
Note: Before unpacking the unit, verify that the machine model is correct and
that there is no damage to the outer packaging. If the outer packaging is in
good condition, proceed to unpack the unit by following these steps:
Note: this machine is heavy! Use a mechanical hoist or the help of two people
to lift if necessary.
- Carefully remove all external wrappings and other protective coverings, including the white plastic coverings on the panels. Begin with unpacking the ice storage bin. Remove the carton, and using part of the carton as a cushion, tip the bin on its back to remove the skid and attach the legs or casters.
- Return the bin to an upright position. Check the bin top gasket for gaps or tears, and fill any in with food-grade sealant prior to placing the ice machine on the bin.
- Review the installation section of the manual completely prior to installing.
- Verify that all accessories are included.
- Properly discard crating materials and recycle if possible.
2.2 Environmental Requirements
The following installation site requirements must be complied with or the system may not operate correctly or damage may occur.
-
Environment temperature must be less than 43°C [109°F] and greater than 3°C [38°F].
WARNING: The machine is for indoor use only. Running the machine below the freezing point is prohibited. Machine failure caused by exposure to freezing temperatures is not covered by the warranty. -
Proper spacing around the unit must be provided. Ice machines, like other refrigeration equipment, emit heat through a condenser and any obstruction of the airflow could affect the machine’s performance and life.
Please refer to the table below for spacing guidelines:
Machine
|
Spacing
---|---
Sides
|
15.0 cm [5.90 in]
Back
|
20.0 cm [7.87 in]
Front
|
30.0 cm [11.81 in]
- The installation site must be leveled. Adjustable feet at the bottom of the machine are provided to level the unit.
- The installation site must be capable of supporting the weight of the ice machine and a full bin of ice.
- The installation site may not be next to heat-generating equipment or in direct sunlight.
- The installation site must be free of airborne and other contaminants that could affect the ice machine’s life or ice quality. Installing your ice machine near a source of yeast or similar material can result in the need for more frequent sanitation cleanings due to the tendency of this material to contaminate the machine.
2.3 Water Supply Requirements and installation
The water used for ice-making must be in accordance with local drinking water
quality standards. An external water filtration device may be installed on the
supply line as long as the required water pressure is maintained.
The following water supply and plumbing requirements must be complied with or
the system may not operate correctly or damage may occur:
-
Water Inlet Temperature must be between 0.6°C [33°F] and 32°C [89.6°F].
WARNING: The ice machine must not be connected to the hot water supply. Please review and comply with the water temperature requirements above. -
Ice Making Water Pressure must be between 0.13 Mpa [19 psi] and 0.55 Mpa [80 psi]. If water pressure exceeds the maximum recommended pressure, a water pressure regulator will be required.
-
Cooling Water Pressure must be between 0.59 Mpa [85.6 psi] and 1.17 Mpa [169.7 psi].
-
Inlet Pipe Diameter must be larger than 9.5 mm [3/8 inch].
-
Drain Pipe Diameter must be larger than 15.8mm [5/8 inch] and drop 3 cm per meter [3/8 inches per foot].
- It is recommended that drains have a joint or other suitable means to allow disconnection from the ice machine when servicing is required.
• All water supply and drain plumbing must comply with local, state, and national codes.
• It is recommended that water supply and drain lines be insulated to prevent condensation.
2.4 Power Supply Requirements
The following electrical supply requirements must be complied with or the system may not operate correctly or damage may occur:
- All wiring must conform to local, state, and national codes.
- The voltage, frequency, and capacity of the power supply provided must be consistent with that marked on the machine nameplate.
- The maximum allowable voltage variation is 10% of the rated voltage on the ice machine model/serial number plate at start-up (when the electrical load is highest).
- The earth terminal of the power supply, socket, or plug must be connected to external grounding.
CHAPTER 3 – OPERATION
3.1 Pre-startup Check
Prior to starting up the unit for the first time or restarting the unit after an extended shutdown, it is important to confirm that all of the installation requirements are met. Please refer back to the “CHAPTER 2 – Installation” section and verify that all requirements are met before proceeding. Make sure that all piping and drain connections are free of leaks.
3.2 Control Panel
There are two types of control panels shown below; with and without a voice warning system.
With voice panel
3.3 Sequence of Operation
-
Startup: Switch on the power at the control panel after the unit has been connected to the power and the water supply. The unit Cleaning switch will start and function automatically if no problem is present. (Note: Please turn off the power supply in case of thunderstorms or a long period of inactivity.)
-
Once the Working status display is started, the ice machine will automatically make ice until the bin or dispenser is full of ice. When the ice level drops, the machine will resume making ice.
-
Pre-cooling: The water inlet will automatically turn on after the power has been switched on before the water Power switch pump starts. The water inlet valve continues to take in water until the water reaches the specified level and the float valve switches off the water inlet.
-
Caution: Do not place anything on top of the ice machine, including the ice scoop. Debris and moisture from objects on top of the machine can work their way into the cabinet and cause serious damage. Damage caused by foreign material is not covered by warranty.
-
Ice making: The water pump starts up after pre-cooling for 30 seconds.
Water continuously flows and ice gradually begins to form as a result. The water float valve will open and close automatically to maintain the proper water level. -
Ice falling: After reaching the required ice-making time, the water pump shuts down and the drain valve closes within 30 seconds. The water valve opens. An entire sheet of ice will slide from the evaporator into the storage refrigerator. This process takes between 1 and 2 minutes. Hands should be away from the storage refrigerator to avoid falling ice.
-
Noise: The ice machine will make noise when it is in ice-making mode. The compressor, fan motor, and water pump all produce some sound. It is also normal to hear some crackling just before the harvest cycle begins. In addition, during the cycle, the harvesting mechanism may click twice as it pushes the ice out and returns to its normal position. The ice harvests as a
unit or slab, which makes some noise when it hits the bin or dispenser.
These noises are all normal for this machine. -
Shutdown: The machine stops when the switch on the control panel is switched off.
-
Automatic Shut-off: Ice will build up in the bin until the sliding board cannot be reset. After the machine has detected that the ice bin is full, the machine will automatically stop. After the ice bin has been emptied enough so that the level switch is reset, the machine will automatically start again.
-
Other Special Stop Conditions:
o There isn’t any ice falling in 3x consecutive cycles. When this occurs, the machine will stop automatically.
o Environmental temperatures exceed the prescribed temperature. This will cause the machine to stop automatically.
o There is no condensed water inside the water-cooled machine. This will also cause the machine to stop automatically. -
Ice thickness adjustment: There are two methods to adjust the ice thickness. Please choose one according to the machine prompts.
o Method I , In the ice-making process, you can click the buttons on the panel to adjust the ice thickness. [see diagram below] o 1. If ice is too thin, press “Ice +”. Once this button is pressed, the Arabic number on the display will increase by 1, and the ice-making time will be extended by 1 minute.
o 2. If ice is too thick, press “Ice -”. Once this button is pressed, the Arabic number on the display will decrease by 1, and the ice-making time will be shortened by 1 minute;
o 3. Ice thickness criteria: the thickness of the hollow part is 1/3 of the entire ice thickness, seen from the side face of ice. The inappropriate thickness of the ice will result in difficulties or failure in ice removal.
o Method II, Should the ice thickness not be satisfactory, the adjusting nut
can be pulled up and rotated to the left or right until the desired thickness
is achieved.
Once this adjustment is complete, press down the adjustment device until it
locks. Note: The adjustment should be limited to one rotation each time until
desired thickness is achieved.
CHAPTER 4 –MAINTENANCE
4.1 Introduction
To ensure the most productive and trouble-free operation, a thorough periodic maintenance schedule is required. Prior to performing any maintenance, these instructions should be followed:
- Before maintenance and repair, the power must be disconnected.
- Maintenance and repair shall only be handled by qualified professionals.
- This manual must be read in detail before performing maintenance or repair.
4.2 Maintenance
The following time-based maintenance plan guidelines are based on general recommendations. Site conditions may dictate a change in the maintenance interval based on air and water conditions. Review your particular maintenance plan with a qualified maintenance professional to determine if changes may be necessary for your ice machine.
A. Monthly Maintenance
-
Remove dust and dirt off exterior surfaces with mild household dishwashing detergent and warm water.
Wipe dry with a clean, soft cloth. -
Inspect the unit to verify that supply and drain hoses are free of obstruction and properly routed.
-
Clean the air filter (only applicable to air cooling machine). Remove the filter as shown in the picture below. Brush clean with soft brush and replace.
B. Six-Monthly Maintenance
- Clean condenser fins. A dirty condenser restricts airflow, resulting in excessively high operating temperatures. This reduces ice production and shortens component life. Follow the steps below
-
Clean the outside of the condenser with a soft brush or a vacuum with a brush attachment. Clean from top to bottom, not side to side, or condenser fins could be damaged.
-
Shine a flashlight through the condenser to check for dirt between the fins. If dirt remains:
A. Blow compressed air through the condenser fins from the inside. Be careful not to bend the fan blades.
B. Use a commercial condenser coil cleaner. Follow the directions and cautions supplied by the cleaner. -
Straighten any bent condenser fins with a fin comb.
-
Carefully wipe off the fan blades and motor with a soft cloth. Do not bend the fan blades.
C. Annual Maintenance -
Clean and sanitize the ice machine. Remove and discard all ice in the holding bin. Wipe down the entire unit with an approved ice machine cleaner and sanitizer.
CHAPTER 5 – TROUBLESHOOTING
This chapter will assist in a systematic check of components in determining the potential causes of equipment failure. The following table lists the most common symptoms that may be experienced and the recommended corrective action.
Troubleshooting Guide
PROBLEM
| PROBABLE CAUSE|
CORRECTION
---|---|---
Ice Machine will not start-up| No power supply| Check the power switch and
power supply
Automatic stop after starting the ice machine for 3 minutes| High-pressure
protection| A. Check ambient temperature meets requirements
B. Clean condenser
C. Check high voltage switch
Ice machine only makes ice once| Ice full| Ice sliding board
Ice cannot fall| A. Ice machine is dirty
B. Ambient temperature is low| A. Clean
B. Check ambient temperature meets the requirement
Ice is too thin or incomplete| A. Tank water level is too low
B. Inlet valve not functioning
C. Water pressure is not enough
D. Water supply obstructed| A. Check the water level
B. Check water inlet valve
C. Verify water pressure meets requirements
D. Check water supply line
Ice making is too slow| A. Condenser is dirty
B. High ambient temperature
C. Poor ventilation| A. Clean the filter and condenser
B. Verify ambient temperature meets requirements
C. Verify spacing around the machine meets requirements
APPENDIX 1 – ERROR CODES
Code| Annotation|
Machine Action
---|---|---
E00| No-fault| Operating
E01| Ice sliding board fault| Protection Shutdown
E02| Overtime ice-making fault| Protection Shutdown
E03| Overtime ice-shedding fault| Protection shutdown
E04| High-temperature fault (voice announcement pressure beyond the limit)|
Protection shutdown
E05| Water shortage fault| Protection shutdown
E06| Excess of pressure limit fault| Protection shutdown
E07| Condensation sensor open circuit fault, display once every 5 seconds|
Nonstop
E08| Condensation sensor short circuit fault, display once every 5 seconds|
Nonstop
APPENDIX 2 – REVISION HISTORY
| Rev | Description of Change | Date |
|---|---|---|
| 1 | Initial Release | September-2017 |
| 2 | 1st Revision | December-2018 |