dyson DC 36 Vacuum Cleaner User Manual
- June 7, 2024
- dyson
Table of Contents
DC 36
OPERATING MANUAL
ASSEMBLY
|
---|---
IMPORTANT!
WASH FILTERS| REGISTER YOUR FREE 5 YEAR
GUARANTEE TODAY
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS
IN THIS MANUAL AND ON THE APPLIANCE
When using an electrical appliance, basic precautions should always be
followed, including the following:
WARNING
These warnings apply to the appliance, and also where applicable, to all
tools, accessories, chargers, or mains adaptors.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
-
This Dyson appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction by a responsible person concerning the use of the appliance to ensure that they can use it safely.
-
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Children should be supervised to ensure that they do not play with the appliance. -
Use only as described in this Dyson Operating Manual. Do not carry out any maintenance other than that shown in this manual, or advised by the Dyson Helpline.
-
Suitable for dry locations ONLY. Do not use outdoors or on wet surfaces.
-
Do not handle any part of the plug or appliance with wet hands.
-
Do not use with a damaged cable or plug. If the supply cable is damaged it must be replaced by Dyson, its service agent or a similarly qualified person in order to avoid a hazard.
-
If the appliance is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors, or dropped into water, do not use and contact the Dyson Helpline.
-
Contact the Dyson Helpline when service or repair is required. Do not disassemble the appliance as incorrect reassembly may result in an electric shock or fire.
-
Do not stretch the cable or place the cable under strain. Keep the cable away from heated surfaces. Do not close a door on the cable, or pull the cable around sharp edges or corners. Arrange the cable away from traffic areas and where it will not be stepped on or tripped over. Do not run the appliance over the cable.
-
Do not unplug by pulling on the cable. To unplug, grasp the plug, not the cable. The use of an extension cable is not recommended.
-
Do not use to pick up water.
-
Do not use to pick up flammable or combustible liquids, such as petrol, or use in areas where they or their vapors may be present.
-
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
-
Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts, such as the brush bar. Do not point the hose, wand, or tools at your eyes or ears or put them in your mouth.
-
Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
-
Use only Dyson recommended accessories and replacement parts.
-
To avoid a tripping hazard wind the cable when not in use.
-
Do not use without the clear bin and filters in place.
-
Do not leave the appliance when plugged in. Unplug when not in use and before servicing.
-
Do not pull or carry by cable or use cable as a handle.
-
Use extra care when cleaning on stairs. Do not work with the appliance above you on the stairs.
-
Turn off all controls before unplugging. Unplug before connecting any tool or accessory.
-
Always extend the cable to the red line but do not stretch or tug the cable.
-
Hold the plug when rewinding onto the cable reel. Do not allow the plug to whip when rewinding.
-
FIRE WARNING – Do not apply any fragrance or scented product to the filter(s) of this appliance. The chemicals in such products are known to be flammable and can cause the appliance to catch fire.
READ AND SAVE THESE INSTRUCTIONS
THIS DYSON APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY
| 
| 
| 
| | 
| |
---|---|---|---|---|---|---|---
Do not pull on the cable.| Do not store near
heat sources.| Do not use near
naked flames.| Do not run over
the cable.| Do not pick up
water or liquids.| Do not pick up burning objects.| Do not use above you on
the stairs.| Do not put hands
near the brush bar
when the appliance
is in use.
Power & cable
Tool attachments
Carpets or hard floors
Brush bar – clearing obstructions
Looking
for blockages
Suction release
Emptying the clear bin
Carrying & storage
IMPORTANT!
WASH FILTER
Cleaning Power & cable
Wash filters with cold water at least every month.
USING YOUR DYSON APPLIANCE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON OPERATING MANUAL
BEFORE PROCEEDING.
CARRYING THE APPLIANCE
- Carry the appliance by the main handle on the body.
- Do not press the cyclone release button or shake the appliance when carrying or the cyclone could disengage, fall off and cause injury.
OPERATION
- Always extend the cable fully to the red tape before use.
- Plug the appliance into the mains electricity supply.
- After use: unplug, retract the cable safely, put the appliance away.
- Switch ‘OFF’ the appliance and unplug before:
– changing tools
– removing the hose or airway inspection parts.
CARPETS OR HARD FLOORS
- The brush bar will always default to ‘ON’ (spinning) each time you switch the appliance ‘ON’.
- The brush bar will automatically stop if it becomes obstructed. See ‘Brush bar – clearing obstructions’.
- To switch the brush bar ‘OFF’ (e.g. for delicate flooring), twist the dial on the cleaner head a quarter of a turn. The brush bar will stop.
- When the appliance is running and the brush bar has been switched ‘OFF’, the brush bar can be switched ‘ON’ again by twisting the dial on the cleaner head a quarter of a turn. The brush bar will start. Alternatively, switch the appliance ‘OFF’; the dial will return to its original position. When the appliance is switched ‘ON’ again the brush bar starts automatically.
- Some carpets may fuzz if a rotating brush bar is used when vacuuming. If this happens, we recommend vacuuming with the brush bar switched ‘OFF’ and consulting with the flooring manufacturer.
- The brush bar on the appliance may damage some carpet types. If you are unsure, turn ‘OFF’ the brush bar.
- This product has carbon fiber brushes. Take care if coming into contact with them, as they may cause minor skin irritation. Wash your hands after handling the brushes.
- Check the brush bar regularly and clear away any debris (such as hair). Debris left on the brush bar may cause damage to flooring when vacuuming.
LOOKING AFTER YOUR DYSON APPLIANCE
- Do not carry out any maintenance or repair work other than that shown in this Dyson Operating Manual, or advised by the Dyson Helpline.
- Only use parts recommended by Dyson. If you do not this could invalidate your guarantee.
- Store the appliance indoors. Do not use or store it below 3°C (37.4°F). Ensure the appliance is at room temperature before operating.
- Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning agents, polishes or air fresheners on any part of the appliance.
- If used in a garage, always wipe the base plate and ball with a dry cloth after vacuuming to clean off any sand, dirt, or pebbles that could damage delicate floors.
VACUUMING
- Do not use without the clear bin and filters in place.
- Fine dirt such as flour should only be vacuumed in very small amounts.
- Do not use the appliance to pick up sharp hard objects, small toys, pins, paper clips, etc. They may damage the appliance.
- When vacuuming, certain carpets may generate small static charges in the clear bin or wand. These are harmless and are not associated with the mains electricity supply. To minimize any effect from this, do not put your hand or insert any object into the clear bin unless you have first emptied it and cleaned it with a damp cloth (see ‘Cleaning the clear bin’).
- Do not work with the appliance above you on the stairs.
- Do not put the appliance on chairs, tables, etc.
- Before vacuuming highly polished floors, such as wood or lino, first, check that the underside of the floor tool and its brushes are free from foreign objects that could cause marking.
- Do not push hard with the floor tool when vacuuming, as this may cause damage.
- Do not leave the cleaner head in one place on delicate floors.
- On waxed floors, the movement of the cleaner head may create an uneven luster. If this happens, wipe with a damp cloth, polish the area with wax, and wait for it to dry.
- To park the wand, collapse the wand and then store the cleaner head by inserting it in the clip at the back of the handle.
EMPTYING THE CLEAR BIN
- Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
- Switch ‘OFF’ and unplug before emptying the clear bin.
- To remove the cyclone and clear the bin unit, press down on the red button on the top of the carrying handle on the cyclone.
- To release the dirt, press all the way down on the same red button on the top of the carrying handle on the cyclone.
- To minimize dust/allergen contact when emptying, encase the clear bin tightly in a plastic bag and empty it.
- Remove the clear bin carefully from the bag.
- Seal the bag tightly, dispose as normal.
- To refit:
– ensure the airway in the bin base is clear of dust and dirt
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance; it will
click into place
– ensure the cyclone and clear bin unit is secure.
CLEANING THE CLEAR BIN
- Remove cyclone and clear bin (see ‘Emptying the clear bin’).
- To separate the cyclone unit from the clear bin press the red button to open the clear bin base. This exposes a small silver button behind the red opening mechanism. Press the silver button and separate the cyclone unit from the clear bin.
- Clean the clear bin with cold water only.
- Do not use detergents, polishes or air fresheners to clean the clear bin.
- Do not put the clear bin in a dishwasher.
- Do not immerse the whole cyclone in water or pour water into the cyclones.
- Clean the cyclone shroud with a cloth or dry brush to remove lint and dust.
- Ensure the clear bin is completely dry before replacing.
- To refit:
– fit the cyclone shroud into the clear bin so that the silver button clicks and engages. Ensure that the front of the clear bin is locked in place
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance; it will click into place
– ensure the cyclone and clear bin unit is secure.
WASHING YOUR FILTERS
- Your appliance has two washable filters, located as shown.
- Check and wash the filters regularly according to instructions to maintain performance.
- Switch ‘OFF’ and unplug before checking or removing the filters.
- The filters may require more frequent washing if vacuuming fine dust.
- Wash the filters with cold water only. Do not use detergents.
- Do not put the filters in a dishwasher, washing machine, tumble dryer, oven, microwave or near a naked flame.
FILTER A
- Remove the cyclone and clear bin (instructions above).
- Release the catch on the front of the cyclone handle. Swing the handle back.
- Lift out the filter.
- Wash the filter with cold water only. Hold under a tap and run water through the open end until the water runs clear. Turn upside down and tap out.
- Squeeze and twist with both hands to make sure the excess water is removed.
- Run water over the outside of the filter until the water runs clear.
- Squeeze and twist with both hands to make sure the excess water is removed.
- Stand the filter on its wide, open end to dry. Leave to dry completely for a minimum of 24 hours.
- Replace the filter into the cyclone. Swing the handle back into place. Ensure the latch clicks to engage and is secure. Fit the cyclone and clear bin unit onto the appliance (instructions above).
FILTER B
-
To remove filter B:
– use a coin to turn the fastener one-quarter anti-clockwise to the unlocked position
–lift out the filter. -
Filter B should be rinsed in cold water only and tapped out until the water runs clear, then tapped out again to ensure all excess water is removed. Tap out on the hard plastic edge of the filter, not the rubber edge. Leave to dry completely for 24 hours.
-
To refit, re-assemble in reverse order.
IMPORTANT: After washing please leave the filters at least 24 hours to dry completely before refitting.
BLOCKAGES – AUTOMATIC CUT-OUT -
This appliance is fitted with an automatic cut-out.
-
If any part becomes blocked the appliance may automatically cut out.
-
This will happen after the motor pulses a number of times (i.e switches on and off in quick succession).
-
If this happens, follow the instructions below in ‘Looking for blockages’.
-
NOTE: Large items may block the tools or wand inlet. If this happens, do not operate the wand release catch. Switch ‘OFF’ and unplug. Failure to do so could result in personal injury.
LOOKING
FOR BLOCKAGES
- Switch ‘OFF’ and unplug before looking for blockages. Failure to do so could result in personal injury.
- Leave to cool down before looking for blockages.
- Beware of sharp objects when checking for blockages.
- To gain access to blockages in the floor tool, remove the base plate by using a coin to loosen the screw marked with a padlock.
- To access the inspection channel, remove the main hose and clear the bin.
- Inspect for blockages.
- Clear any blockage before restarting.
- Refit all parts securely before using.
- Clearing blockages is not covered by your Dyson guarantee.
BRUSH BAR – CLEARING OBSTRUCTIONS
- If your brush bar is obstructed, it may shut ‘OFF’. If this happens you will need to remove the brush bar as shown.
- Switch ‘OFF’ and unplug before proceeding. Failure to do so could result in personal injury.
- Remove the brush bar by using a coin to loosen the fastener marked with a padlock until it clicks.
- Beware of sharp objects when clearing obstructions.
- Replace the brush bar and secure it by tightening the fastener until it clicks. Ensure it is fixed firmly before operating.
- Clearing brush bar obstructions is not covered by your guarantee.
- This product has carbon fiber brushes. Take care if coming into contact with them, as they may cause minor skin irritation. Wash your hands after handling the brushes.
BRUSH BAR – TROUBLESHOOTING
- If the brush bar has stopped spinning, follow the instructions above on clearing obstructions. Alternatively, contact a Dyson expert on the Dyson Helpline or visit the website.
DISPOSAL INFORMATION
- Dyson products are made from high-grade recyclable materials. Recycle where possible.
GUARANTEE TERMS AND CONDITIONS
DYSON CUSTOMER CARE
THANK YOU FOR CHOOSING TO BUY A DYSON APPLIANCE
After registering your 5-year guarantee, your Dyson appliance will be covered
for parts and labor for 5 years from the date of purchase, subject to the
terms of the guarantee. If you have any questions about your Dyson appliance,
call the Dyson Helpline with your serial number and details of where/when you
bought the appliance. Most questions can be solved over the phone by one of
our trained Dyson Helpline staff.
Visit www.dyson.com for online help, support videos,
general tips and useful information about Dyson.
If your Dyson appliance needs service, call the Dyson Helpline so we can
discuss the available options. If your Dyson appliance is under guarantee,
and the repair is covered, it will be repaired at no cost.
PLEASE REGISTER AS A DYSON APPLIANCE OWNER
To help us ensure you receive prompt and efficient service, please register as
a Dyson appliance owner. There are two ways to do this:
- By email.
- By calling the Dyson Helpline.
This will confirm ownership of your Dyson appliance in the event of an insurance loss, and enable us to contact you if necessary.
LIMITED 5 YEAR GUARANTEE
-
TERMS AND CONDITIONS OF THE DYSON 5 YEAR LIMITED GUARANTEE.
WHAT IS COVERED -
The repair or replacement of your Dyson appliance (at Dyson’s discretion) if it is found to be defective due to faulty materials, workmanship or function within 5 years of purchase or delivery (if any part is no longer available or out of manufacture Dyson will replace it with a functional
-
This guarantee will only be valid if the appliance is used in the country in which it was sold.
WHAT IS NOT COVERED
- Dyson does not guarantee the repair or replacement of a product where a defect is a result of:
- Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation, or handling of the appliance which is not in accordance with the Dyson Operating Manual.
- Use of the appliance for anything other than normal domestic household purposes.
- Use of parts not assembled or installed in accordance with the instructions of Dyson.
- Use of parts and accessories which are not genuine Dyson components.
- Faulty installation (except where installed by Dyson).
- Repairs or alterations carried out by parties other than Dyson or its authorized agents.
- Blockages – please refer to the Dyson Operating Manual for details of how to look for and clear blockages.
- Normal wear and tear (e.g. fuse, brush bar etc.).
- Use of this appliance on rubble, ash, plaster.
- Reduction in battery discharge time due to battery age or use (where applicable). If you are in any doubt as to what is covered by your guarantee, please contact Dyson.
SUMMARY OF COVER
- The guarantee becomes effective at the date of purchase (or the date of delivery if this is later).
- You must provide proof of (both the original and any subsequent) delivery/ purchase before any work can be carried out on your Dyson appliance. Without this proof, any work carried out will be chargeable. Keep your receipt or delivery note.
- All work will be carried out by Dyson or its authorized agents.
- Any parts which are replaced by Dyson will become the property of Dyson.
- The repair or replacement of your Dyson appliance under guarantee will not extend the period of guarantee.
- The guarantee provides benefits that are additional to and do not affect your statutory rights as a consumer.
ABOUT YOUR PRIVACY
By providing your details upon warranty registration, you would have consented
to the use of your information by Dyson. Dyson may use this information for
future marketing and research purposes (including sending commercial
electronic messages) and may disclose it to third parties for the purposes of
providing the services you have requested or to our business partners or
professional advisers. If you wish to access your personal information or see
our full privacy policy, please contact the Dyson Helpline.
MARKING FOR NAME & CONTENT OF TOXIC OR HAZARDOUS SUBSTANCES OR ELEMENTS
| Part Name | Toxic or Hazardous Substances or elements |
|---|---|
| Cadmium | Lead |
| External chassis, body | 0 |
| Internal chassis | 0 |
| Internal wire & cable | 0 |
| Foam materials gl14411 | 0 |
0
Screws & nuts | 0| 0| 0| 0| 0| 0
Brush bar assembly| 0| 0| 0| 0| 0| 0
Hose assembly| 0| 0| 0| 0| 0| 0
Wand assembly| 0| 0| 0| 0| 0| 0
Cyclone assembly| 0| 0| 0| 0| 0| 0
Duct assembly| 0| 0| 0| 0| 0| 0
Printed circuit board & components | 0| 0| 0| 0|
0| 0
Internal wire| 0| X”‘| 0| 0| 0| 0
Metals in Commutator| 0| X”‘| 0| 0| 0| 0
O: Indicate that this toxic or hazardous substance contained in all of the
homogeneous materials for this part is within the limit requirement in
SJ/T11363-2006.
X: Indicate that this toxic or hazardous substance contained in at least one
of the homogeneous materials used for this part exceeds the limit requirement
in SJ/T11363-2006.
(1) Toxic or hazardous substance contained is exempted under EU RoHS directives exemption list (2011/65/EU Annex II, recasting 2002/95/EC).
Disclaimer:
The environment safe use period is declared based on the normal temperature &
humidity used conditions.
DYSON CUSTOMER CARE
THANK YOU FOR CHOOSING TO BUY A DYSON APPLIANCE
After registering your 5-year guarantee, your Dyson appliance will be covered
for parts and labor for 5 years from the date of purchase, subject to the
terms of the guarantee. If you have any questions about your Dyson appliance,
call the Dyson Helpline with your serial number and details of where/when you
bought the appliance. Most questions can be solved over the phone by one of
our trained Dyson Helpline staff.
Visit www.dyson.com for online help, support videos,
general tips, and useful information about Dyson.
Your serial number can be found on your rating plate which is on the main body of the appliance behind the clear bin.
This illustration is for example purposes only.
REGISTER YOUR FREE 5 YEAR GUARANTEE TODAY
REGISTER BY EMAIL
CN: china.service@dyson.com
HK: pidcs@jebsen.com
REGISTER BY PHONE
CN: 4009 202 808
HK: 2926 2300
IMPORTANT!
WASH FILTER
Wash filters with cold water at least every month.
Dyson Customer Care
If you have a question about your Dyson appliance, call the Dyson Helpline
with your serial number and details of where and when you bought the
appliance, or contact us via the Dyson website.
HK
Jebsen Consumer Products Company Limited
pidcs@jebsen.com
2926 2300
10/F, Continental Electric Building, 17 Wang
Chiu Road, Kowloon Bay, Kowloon, Hong Kong
www.jebsenconsumer.com
www.dyson.com
cs.dyson@e-metrox.com
+62 21 29668888 ext. 1041, 1042
Jalan Raya Kebayoran Lama No. 396
R T 01/ R W11
(Rawa Belong)
Sukabumi Utara – Kebon Jeruk
Jakarta Barat 11540
Indonesia
www.dyson.co.id
References
- Dyson Indonesia | Official Site | Shop
- Dyson ประเทศไทย | เว็บไซต์อย่างเป็นทางการ | ร้านค้า
- Dyson Singapore | Official Site | Shop
- Dyson Philippines | Official Site | Shop
- Dyson台灣| 官方網站
- Jebsen Consumer Products
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>