Jabra Bluetooth Headset User Manual
- June 7, 2024
- Jabra
Table of Contents
Bluetooth Headset
Jabra® BT2047
USER MANUAL
A BRAND BY
THANK YOU
Thank you for purchasing the Jabra BT2047 headset. We hope you enjoy it! This instruction manual will get you started and ready to make the most of your headset.
ABOUT YOUR JABRA BT2047
A Answer/end button, on/off button
B LED light
C Charging socket
D Earhook
WHAT YOUR HEADSET CAN DO
Your Jabra BT2047 lets you do all this:
– Answer calls
– End calls
– Reject calls
– Voice dialing
– Last number redialing
– Call waiting
– Place call on hold*
- Phone dependent 2
Specifications
– Talk time up to 10 hours / standby time up to 10 days
– Weight 10 grams
– Operating range up to 10 meters (appr. 33 feet)
– Headset and hands-free profiles (see glossary)
– Bluetooth® version 2.1 + eSCO & EDR
GETTING STARTED
You should follow three steps before using your headset:
- Charge your headset
- Activate Bluetooth® on your mobile phone (refer to the manual for your Mobile phone)
- Pair your headset to your mobile phone
The Jabra BT2047 is easy to operate. The answer/end button on the headset performs different functions depending on how long you press it.
| Instruction | Duration of press |
|---|---|
| Tap | less than 1 sec |
| Press | Approx: 2 sec |
| Long press | Approx: 5 sec |
3
CHARGE YOUR HEADSET
Make sure that your headset is fully charged for 2 hours before you start using it. When the light indicator (LED) has a solid LED light, your headset is charging. When the solid LED light turns off, it is fully charged.
Please note: The lifetime of the battery will be significantly reduced if your device is left uncharged for a long period. We therefore recommend that you recharge your device at least once a month.
TURNING YOUR HEADSET ON AND OFF
– Press the answer/end button until you see a burst of flashes on the
indicator light (LED) to turn on your headset.
– Long press the answer/end button until you see a burst of flashes on
the indicator light (LED) to turn the headset off.
Please note that the LED indicator light turns off after 1 minute to save
battery. Headset is still active, and light will flash again after tap on the
Answer/End button or any call activity. To check if the headset is on, tap the
answer/end button once the LED indicator light will flash, if the headset is
on.
PAIRING IT WITH YOUR PHONE
Headsets are connected to phones using a procedure called ‘pairing’. By following a few simple steps, a phone can be paired with a headset in a matter of minutes.
-
Put the headset in pairing mode
– When you turn on your Jabra BT2047 for the first time, the headset will automatically start up in pairing mode - i.e. it is discoverable for your phone. When the headset is in pairing mode the LED is constantly lit. -
Set your phone to ‘discover’ the Jabra BT2047
– Follow your phone’s instruction guide. First make sure that Bluetooth® is activated on your mobile phone. Then set your phone to discover the headset. This usually involves going to a ‘setup’, ‘connect’ or ‘Bluetooth®’ menu on your phone and selecting the option to ‘discover’ or ‘add’ a device.* -
Your phone will find the Jabra BT2047
– Your phone will find the headset under name “BT2047”. Your phone then asks if you want to pair with the headset. Accept by pressing ‘Yes’ or ‘OK’ on the phone and confirm with the passkey or PIN = 0000 (4 zeros) if asked. Your phone will confirm when pairing is complete.
5
Put the headset in pairing mode manually
In case of unsuccessful pairing, put the Jabra BT2047 into pairing mode
manually. Make sure the headset is off. Press and hold the answer/end button
for approximately 5 seconds until the LED has a constant light. The LED will
flash before the light is constant keep holding down the button until light
is constant. Then follow the steps 2 and 3 above.
WEAR IT HOW YOU LIKE IT
The Jabra BT2047 is designed to wear with an earhook but it can also be worn without the earhook by simply inserting it in your right or left ear. If you prefer to use the earhook, click it on as shown on the illustration.
For optimal performance, wear the Jabra BT2047 and your mobile phone on the same side of your body or within line of sight. In general, you will get better performance when there are no obstructions between your headset and your mobile phone.
6
HOW TO
Answer a call
– Tap the answer/end button on your headset to answer a call.
End a call
– Tap the answer/end button to end an active call.
Make a call
– When you make a call from your mobile phone, the call will (subject to phone
settings) automatically transfer to your headset. If your phone does not
support this function, tap on the answer/end button on the Jabra BT2047 to
receive the call in the headset.
**Reject a call***
– Press the answer/end button when the phone rings to reject an in-coming
call. Depending on your phone settings, the person who called you will either
be forwarded to your voice mail or hear a busy signal.
**Activate voice dialing***
– Press the answer/end button to activate the voice-dialing function in the
mobile phone. Please consult your phone user manual for more info about using
this feature.
**Redial last number***
– Double tap the answer/end button.
**Call waiting and placing a call on hold***
– This lets you put a call on hold during a conversation and answer a waiting
call.
– Press the answer/end button once to put the active call on hold and answer
the waiting call.
– Press the answer/end button to switch between the two calls.
– Tap the answer/end button to end the active conversation.
Functions marked with* are dependent on your phone supporting these features. Check your phone’s user manual for further information.
7
WHAT THE LIGHTS MEAN
| What you see | What that means |
|---|---|
| Solid light | In pairing mode – see Pairing section. |
| Very slow single flash | Connected to phone and in standby mode.* |
| Slow triple flash | Not connected to phone and in standby mode.* |
| Regular double flash | Active on call |
| Quick double flash | Incoming/Outgoing call |
| Quadruple flash | Battery low |
*BT2047 is equipped with Jabra Discreet Light feature, meaning that light indicator (LED) turns off after 1 min of non-activity. Headset is still active, and light will flash again after a tap on the answer/end button or any call activity.
USING JABRA BT2047 WITH TWO MOBILE PHONES
Jabra BT2047 is capable of having two mobile phones (or Bluetooth® devices) connected to the headset at the same time. This will give you the freedom of having only one headset to operate both your mobile phones.
In order to use the headset with two mobile phone please make sure you have “paired” the Jabra BT2047 with both phones. See the section “PAIRING IT WITH YOUR PHONE” for instructions.
Once you have “paired” your headset with two phones simply make sure your headset is on, and that Bluetooth® is enabled on the phones and the headset will then automatically connect to both phones.
Please note that Last Number Redial will dial the number from the last outgoing call, independent of the mobile phone, and the Voice Dialing function will only work on the last paired mobile phone.
8
If you are on a call and receive a second call you will be alerted by a tone.
You can then:
– Put the first call on hold and accept the incoming call by pressing the
Answer/end button
– Switch between the two active calls by pressing the Answer/ end button
again
– Tap the Answer/end button once to end the first call and accept the new
incoming call
TROUBLESHOOTING & FAQ
I hear crackling noises
– For the best audio quality, always wear your headset on the same side of the
body as your mobile phone.
I cannot hear anything in my headset
– Increase the volume on your phone.
– Ensure that the headset is paired with the phone.
– Make sure that the phone is connected to the headset if it does not
connect either from the phone’s menu or by tapping the answer/end button,
follow the pairing procedure (refer to pairing section in this user manual).
– You can determine whether your headset is connected to a device by looking
at the flashes on the headset after tapping the answer/end button when the
headset is on very slow single flashes means that the headset is connected to
a device, slow triple flashes means that the headset is currently not
connected.
I have connection problems
– You may have deleted your headset pairing connection in your mobile phone.
Follow the pairing instructions (refer to the section in this user manual).
– You can determine whether your headset is connected to a device by looking
at the flashes on the headset after tapping the answer/end button when the
headset is on very slow single flashes means that the headset is connected to
a device, slow triple flashes means that the headset is currently not
connected.
9
Will the Jabra BT2047 work with other equipment?
– The Jabra BT2047 is designed to work with mobile phones. It can also work
with other devices that are compliant with Bluetooth® and support a headset
and/or hands-free profile.
I cannot use Reject call, Call on hold, Redial or Voice dialing
– These functions are dependent on your phone supporting them. Please check
your phone’s manual for further details.
NEED MORE HELP?
Web: www.jabra.com/bt2047
(for the latest support info and online User Manuals)
TAKING CARE OF YOUR HEADSET
– Always store the Jabra BT2047 with the power off and safely protected
– Avoid storage at extreme temperatures (above 45°C/113°F including direct
sunlight - or below -10°C/14°F). This can shorten battery life and may affect
operation. High temperatures may also degrade performance.
– Do not expose the Jabra BT2047 to rain or other liquids.
10
GLOSSARY
1 Bluetooth® Bluetooth® is a radio technology that connects devices, such as mobile phones and headsets, without wires or cords over a short distance (approx. 10 meters/33 feet). is safe to use. It is secure too, so once a connection has been made no-one can listen in and there is no interference from other devices either. Get more information at www.bluetooth.com.
2 Bluetooth® profiles are the different ways that devices communicate with other devices. Phones support the headset profile, the hands-free profile or both. In order to support a certain profile, a phone manufacturer must implement certain mandatory features within the phone’s software.
3 Pairing creates a unique and encrypted link between two Bluetooth® devices and lets them communicate with each other. Bluetooth™ devices will not work if the devices have not been paired.
4 Passkey or PIN is a code that you enter on your Bluetooth® enabled device (e.g. a mobile phone) to pair it with your Jabra BT2047. This makes your Bluetooth® device and the Jabra BT2047 recognize each other and automatically work together.
5 Standby mode is when the Jabra BT2047 is passively waiting for a call. When you ‘end’ a call on your mobile phone, the headset goes into standby mode.
Dispose of the product according to local standards and regulations.
11
A BRAND BY
© 2016 GN Netcom A/S. All rights reserved. Jabra® is a registered trademark of GN Netcom A/S. All other trademarks included herein are the property of their respective owners. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by GN Netcom A/S is under license. (Design and specifications subject to change without notice).
MADE IN CHINA
MODEL : OTE9 / Jabra BT2046 series
www.jabra.com/bt2047
REV B
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>