V-TAC Motion Sensor Instructions
- June 7, 2024
- V TAC
Table of Contents
INNOVATIVE LED LIGHTING
WEEE NUMBER:8013970
INSTALLATION INSTRUCTION
INFRARED SENSOR
TECHNICAL DATA:
| Power Sourcing: | 220-240V/AC |
|---|---|
| Power Frequency: | 50/60Hz |
| Ambient Light: | <3-2000LUX (adjustable) |
| Time Delay: | Min.10sec±3sec |
Max. 15min±2min
Rated Load| 800W (Traditional Lighting)
400W (LED Lighting)
Detection Range:| 360°
Detection Distance:| 8m max(<24°C)
Working Temperature:| -20~+40°C
Working Humidity:| <93%RH
Installing Height:| 2.2-4M
Power Consumption:| approx 0.5W
Detection Motion Speed:| 0.6-1.5m/s
INTRODUCTION & WARRANTY
Thank you for selecting and buying the V-TAC product. V-TAC will serve you the
best. Please read these instructions carefully before starting the installing
and keep this manual handy for future reference. If you have any other
queries, please contact our dealer or local vendor from whom you have
purchased the product. They are trained and ready to serve you at your best.
The warranty is valid for 2 years from the date of purchase. The warranty does
not apply to damage caused by incorrect installation or abnormal wear and
tear. The company gives no warranty against damage to any surface due to
incorrect removal and installation of the product. This product is warranted
for manufacturing defects only.
WARNING!
- Please make sure to turn off the power before starting the installation.
- Install only by certified Electrician.
This marking indicates that this product should not be disposed of with other household wastes.
Caution, risk of electric shock.
FUNCTION:
- Can identify day and night: The consumer can adjust working state in different ambient light. It can work in the daytime and at night when it is adjusted on the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern.
- Time-Delay is added continually: When it receives the second induction signals within the first induction, it will restart to time from the moment.
INSTALLATION ADVICE:
As the detector responds to changes in temperature, avoid the following situations:
- Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors, etc.
- Avoid mounting the detector near heat sources, such as heating vents, air conditioning units, light, etc.
- Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants, etc.
INSTALLATION:
- Switch off the power before starting the installation
- Turn clockwise the plastic cover that is on the top of the sensor and adjusts the time and LUX knob.
- Loose the screws in the connection terminal and then connect the power to a connection terminal of a sensor according to the connection-wire diagram.
- Fold the metal spring of the sensor upwards, until they are in the “I” position with the sensor, and then put the sensor into the hole or installation box which is on the ceiling and has a similar size to the sensor. Releasing the spring, the sensor will lock into its installation position.
- After finishing Installation, turn on the power and then test it.
INSTALLATION DIAGRAM
- Turn the LUX knob clockwise on the maximum (sun). Turn the TIME knob anti-clockwise on the minimum (10s) (Refer to figure1).
- Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After a Warm-up time of 30sec, the sensor will start working. If the sensor receives the induction signal, the lamp will turn on. While there is no other induction signal, the load should stop working within 10sec±3sec and the lamp will turn off (Refer to figure 1).
- Turn the LUX knob anti-clockwise on the minimum (3). If the ambient light is more than 3LUX, the sensor will not work and the lamp stops working too. If the ambient light is less than 3LUX (darkness), the sensor will work. Under no induction signal condition, the sensor should stop working within 10sec±3sec (Refer to figure 1).
Note: when testing in daylight, please turn the LUX knob to SUN position, otherwise the sensor lamp will not work!
In case of any query/issue with the product, please reach out to us at: support@v-tac.eu For More products range, inquiry please contact our distributor or nearest dealers. V- TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>