MILLITRONIC HIVE Wireless USB3.0 transmitter Wireless Dock receiver User Manual

June 7, 2024
MILLITRONIC HIVE

Wireless USB3.0 transmitter
Wireless Dock receiver

MILLITRONIC HIVE Wireless

Driver Installation & User Manual
Supervised By MILLITRONIC Co., LTD
August, 2019
Version: 3.0 7AD000000003(A)

Introduction
Thank you for purchasing this MILLITRONIC product. You can visit our website: www.millitronic.com.tw
Trademarks ™ MILLITRONIC CO., LTD
Logo are owned by MILLITRONIC CO.,
LTD Any non MILLTRONIC trademarks
are used for reference purposes only.

Overview

Product Description
The Millitronic HIVE WiGig Docking station lets you wirelessly connect your Windows 10 laptop to a big-screen display.
Enjoy a brand-new, latency-free user experience that is free of annoying cables with  0GHz Wireless  Gigabit technology. Connect any monitor via the HDMI /VGA port on the Millitronic HIVE WiGig Docking station, then wirelessly connect your windows 10 laptop via WiGig. The pleasures of near-zero latency (under 30ms) will significantly enhance your productivity.
UNIVERSAL DOCKING STATION: The Millitronic  Hive WiGig Docking station is compatible with all PC laptops (Windows 10 64bit) that are equipped with USB3.0 ports.
CONNECT DISPLAY: Hook up the projector/monitor to the docking station using the VGA and HDMI ports.

MORE PORTS: Connect a variety of peripherals to Millitronic HIVE Docking station with one USB3.0 port, one  DMI and one VGA port, and a Gigabit Ethernet port.

This Package Includes The Following:
– Wireless USB3.0 transmitter: 1 unit.
– Wireless Dock receiver: 1 unit.
– Power Adapter (output DC 12 V): 1 unit
– User manual
– Warranty card: 1 year
In Following Demonstration, The Following Is Required:
– One laptop
– One displayer with HDMI / VGA connector
– One HDMI / VGA cord
Features:
– HDMI/VGA Output.
– Size: 183mm X 122mm.
– Low latency display.

Specification

Wireless Dock Receiver

Wireless
60GHz Radio
Adaptive 180 Degree Beamforming
Connection Interface
Compliant with USB 3.0 / 2.0
Compliant with HDMI/VGA (Single output)
Ethernet
Dimension
Size: 185 x 120.7 x 40.3 mm
Weight: 246 g
Certification
FCC approved for indoor use
Power
DC 12V-1A in

MILLITRONIC HIVE Wireless - Wireless Dock Receiver Wireless USB3.0 Transmitter

MILLITRONIC HIVE Wireless - Wireless USB3.0
Transmitterr

Wireless
60GHz Radio
Adaptive 360 Degree Beamforming
Features
USB 3.0 plug and play, driver included
Storage: 8GB
Connection Interface
Compliant with USB 3.0 Type A
Driver Support
Windows 10, 64-bit RS3 v1709 above only
Dimension
Size: 110.3 x 59.3 x 17.3 mm
Weight: 65 g
Certification
FCC approved for indoor use
Power
USB bus power 5V

The Working AreaMILLITRONIC HIVE Wireless - The Working
Area

The Working Area

The working range of the dock is a half-circle in front of itself, with a radius of 5 meters. The dock should be placed as the same level as the dongle or within 1m higher than the dongle.
Our dongle is omnidirectional and can be plugged through the left or right side of the laptop.
The network connect session will disconnect after leaving the working range. However, the LED light or UI will only respond 60 seconds later.

Chapter 1 – Installing the dock

Step 1 – Setting Up The Dock

To set up the dock, do the following:

MILLITRONIC HIVE Wireless - To set up the dock

1. External Monitor
2. VGA Table
3. HDMI Table
4. Dock| 5. AC Power Adapter
6. Laptop
7. Dongle
---|---

◘ Connect the power adapter to the power connector of the dock.
◘ Plug the power adapter to an electrical socket.
◘ Turn on the dock by pressing the power button.
◘ If an external monitor is available, connect the external monitor to the appropriate connector (HDMI or VGA  onnector) on the dock.
◘ Position your laptop close to the dock, within 5m (16 feet).Make sure the dongle face to the dock.

Step 2 – Execution The Installer
Driver InstallationMILLITRONIC HIVE Wireless - Driver
Installation

MILLITRONIC HIVE Wireless - Driver Installation 2

The USB driver should be enabled and the window automatically displayed, allowing you to follow the steps below. If no window pops up, please check the CD Drive“ under ”This PC”. When your laptop displays the contents as below,
please double click to continue.
Please note that the installer only installs the drivers for Hive. If your USB device requires a vendor driver, install your  SB device driver.Visit:http://millitronic.com.tw for new updates.

◘ After executing the installer, it will guide you  through the installation of the MilliDock application. Click “Yes” to continue the installation

MILLITRONIC HIVE Wireless - double click1

◘ It will then display the screen below. Please click the “Next” button to continue with installation.

MILLITRONIC HIVE Wireless - Installing the dock

Step 3 – License Agreement And Choose components
◘ The License Agreement is then shown. Choose “I accept …” and click “Next” to continue.

MILLITRONIC HIVE Wireless - double click3

◘ The user can select the components to install during this phase. All of these drivers are needed for MillitronicDock to operate. Click “Next” to continue with the installation.

MILLITRONIC HIVE Wireless - double click4

Step 4 – Choosing Install Location And Start To Install

◘ Choose the install path and click “Install” to start to begin the installation.

MILLITRONIC HIVE Wireless - double click5

◘ Please wait for the installation process to complete.

MILLITRONIC HIVE Wireless - double click6

Step 5 – Installation Complete
◘ Click “OK” to close this window and complete the installation.

MILLITRONIC HIVE Wireless - Installation Complete

Chapter 2 – User Manual
Using The “MilliDock” App

◘ After finishing the installation, the icon of the App will appear on your desktop. Click the icon to start the App.

MILLITRONIC HIVE Wireless - Installation Complete 1

◘ Click “Yes” to continue the MilliDock App.

◘This will automatically connect to the dock. Just wait for the connection.

MILLITRONIC HIVE Wireless - AConnection Success

Waiting For The First Time Auto Initializing
◘ For the first time launch, the MilliDock will connect, then initialize and display automatically. It will show this  message  t the right-bottom corner. Just wait a minute for auto initializing the display card.

MILLITRONIC HIVE Wireless - Auto Initializing

The Status Of The MilliDock App

There are several messages which indicate the status of the MilliDock App. The explanations for the different statuses are shown below:.

No Device:
◘ If the dongle isn’t plugged into the laptop when the app starts, it would display a “No Device” status and the start button will not be clickable.

Loading:
◘ When the dongle is detected, it will display a “Loading”  message while the computer checks the settings of the dongle. Just wait for the process to finish.

Scanning and Autoconnection:
◘ When the dongle is not connected to the dock, it will display a “Scanning” message and proceed to search the SSID of the dock. The computer will automatically connect to the dock when the dock is scanned by the dongle. Please wait for the process to finish.

Waiting:
◘ If the App shows this status, wait for a moment and it will change to other status. If the status keeps over 3 mins, exit the App and restart the App again.

Ready to Start:
◘ When the preparation is done, it will display an “OK” message  and the start button will beenabled. Click “Start”  button to start the dock link and display the screen.

Connection Success
◘ After few seconds, it would display a “Connect to server” message and the screen will be shown at the second monitor.

◘ You can check the status of the 2nd monitor under Windows advanced display settings

Connection Success

Stop and Exit
◘ If you want to finish the display, you can click the “Stop” button to finish.

◘ Right-click the icon on the toolbox and click “Exit” to stop and terminate the App.

Settings
◘ Right click the icon on the toolbox, click “Setting” on the menu and a form as shown below will appear.

◘ You can change the settings through the following steps:
1. Scan SSID: When more than one dock is present, you can select which dock to connect to by assigning the SSID of the target dock. Change the scanning SSID of the dock.
2. Hidden Form: Hide the main form.
3. AutoStart: Clicking AutoStart will allow the application to “Start” on default. If AutoStart is not selected, the application will not take action and the user will need to click the “Start” button.

Uninstalling MilliDock App
1. Open “Apps & feature”, and then find “MilliDock”.Click the “Uninstall” button to uninstall MilliDock App.

Connection Success-2

2. Reboot your system to finish the uninstallation process.

MILLITRONIC HIVE Wireless - Apps & feature 2

**Federal Communication Commission Interference Statement Millitronic

MG360
**

FCC ID: 2AJASU3WG360

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits e designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  owever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  radio- television reception, which can be determined by turning the equipment off and on, the user is  encouraged to  ry to correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 7 cm between the radiator & your body.

Multitronic Hive Wireless Dock Receiver
Contains FCC ID: 2AJAS2019M2

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against armful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  radio or television reception,which can be determined by turning the equipment  off and on, the user is encouraged to try to correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a  circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including nterference that may cause undesired operation.
Professional installation is required

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used.

USERS MANUAL OF THE END PRODUCT:
In the user manual of the end product, the end-user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end-user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied.
The end-user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.  This device complies with Part 15 of FCC rules. Operation s subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following ” Contains FCC ID:2AJAS2019M2″.
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:  (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Bran Model Name AntennaType Connector Gain (dBi)
Multitronic MLPBM2 Printed antenna N/A 11

This Module may not be integrated into host devices that are addressed for operation inside airplanes/ satellites.

Appendix 1:
Wireless USB3.0 transmitter light signals
In USB 3.0 Port

Green Blue Red Gray
Ready to Use Connecting Error No power

In USB 2.0 Port

2 Green + Red 2 Green + Blue
Ready to Use Connecting

If the signal is not green or blue, unplug and reconnect the transmitter.

Appendix 2: Safety Information
1.This product can only be used in rooms at 26 degrees Celsius (Fahrenheit 78.8), please do not use the product in a non-ventilated environment.
2. Avoid covering the machine when the machine is in use.
3.Pull out from the bottom when removing the dongle

Appendix 3: Troubleshooting
Not Detection Of The Driver Of The Components:
In this case, follow the steps of “Uninstall MilliDock App” to uninstall the MilliDock app and restart the laptop. einstall the app then launch again.

MILLITRONIC HIVE Wireless -Troubleshooting

Connect Server Fail:
In this case, wait for 10 seconds then click “Start” again.

MILLITRONIC HIVE Wireless - Troubleshooting 2

Display Card Initialization Failed:
In this case, wait for 10 seconds and reconnect again. If this error message still shows, follow the steps of “Uninstall illiDock App” to uninstall the MilliDock app and restart the laptop. Reinstall the app then launch again.

MILLITRONIC HIVE Wireless - Troubleshooting 3

Unpredictable Error Has Occurred:
In this case, exit the App and restart the App again.

MILLITRONIC HIVE Wireless - Troubleshooting 4

The Dock Is Busy:
There is another user connected to this dock. The dock is occupied by another user. If the dongle is unplugged before you stop the app or before the WiGig network is disconnect, the dock may hold this status for 1 min. In this case, wait 1 min and click “Start” again.

MILLITRONIC HIVE Wireless - The Dock Is Busys

My USB device does NOT work:
The Hive installer only installs the drivers for Hive. If your USB device requires vender driver, install your USB device driver.
My WiFi can NOT work:
The dock creates a separate WiFi network and takes over internet access for the laptop. You can NOT access WiFi and the dock simultaneously. Connect an ethernet cable to the dock. You can access network through the dock.

Fail To Connect
To The Dock:
The status keeps in “Scanning”. Power cycle the dock and wait 1 min. Make sure the laptop display does not block the ock and there is no object between the dongle and the dock. Refer to “The Working Area”

No Device:
If the dongle already connects to the laptop but the app displays “No Device”, unplug the dongle and re-connect it to the laptop.

No image or if the image is stuck, or is blank on the2nd monitor:
If the image on the 2nd monitor is not working properly, click “stop” on the app and click “start” again after 10s. If this does not work, power cycle the dock. Wait 1 min for the dock to reboot. Then connect to the dock again.
USB device can NOT work properly when connected to the dock:
The USB bus power of the dock is 5v 900mA, which is of the standard USB3.0. If your device requires more than900mA, connect to a USB hub with external power.
We have tested most standard USB devices with Win10inbox drivers. If your USB device uses a vendor driver, it may
not work properly. Please inform us if you experience such issues.
USB camera does NOT work smoothly:
We suggest using the compressed image format when running the USB camera. If the compressed image format
is still not stable, please try a lower resolution like HD.

7F-6., No. 237, Sec. 1, Datong Rd.,
Xizhi Dist. New Taipei City 221,
Taiwan
www.millitronic.com.tw

www.millitronic.com.

Documents / Resources

| MILLITRONIC HIVE Wireless USB3.0 transmitter Wireless Dock receiver [pdf] User Manual
Wireless USB3.0 transmitter Wireless Dock receiver
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals