Shenzhen Shanling Digital Technology Development BH5 Bluetooth Headphone Amp User Guide
- June 4, 2024
- Shenzhen Shanling Digital Technology Development
Table of Contents
Shenzhen Shanling Digital Technology Development BH5 Bluetooth Headphone Amp User Guide
Security Instructions
- Don’t repair, disassemble or modify the device without permission.
- Please don’t use this device in extremely hot, cold, dusty or humid circumstances. Avoid any exposure to liquids.
- It is normal that the device might get warm during charging.
- Prevent device from falling, friction, or crashing against hard objects during use, otherwise surface scratch, battery disconnection, data loss or other hardware damages will be caused. Please also avoid violent vibration or impact.
- Please enjoy the music at a proper volume to avoid impairing your hearing and damaging the sound system. Before plugging your headphones into the device, please turn down the volume first.
- Don’t clean this device with chemicals or detergents, otherwise its surface and top coating may be damaged.
- The USB port is only for data transmission or charging. Please try to avoid using this device when it is charging.
- When the device is not in use, please charge it regularly to guarantee battery life.
- Please replace the battery with one of the same type as the original one, as improper replacement might cause explosion.
- Never expose battery to sunlight, fire or other extremely hot circumstances.
Names of Parts
Operation Instructions
Power ON / OFF / Screen Lock
- Power on: Press and hold the multifunctional button for 2.5 seconds. Display will turn on.
- Power off: Press and hold the multifunctional button for 2.5 seconds, until Display turns off.
- Screen lock: Short press the multifunctional button to turn display on and off. This function is limited during calls and while browsing menu.
Pairing Mode
- With the UP5 turned off, press and hold the multifunctional button for 4 seconds, until “PAIRING” shows up on the display.
- If UP5 Is turned on, but not connected, double tap the multifunctional button to enter the pairing mode. Display will show “PAIRING”.
- If UP5 disconnects from paired phone, it will automatically enter pairing mode.
Pairing Timeout
If no phone is paired with the UP5 in 5 minutes after entering the pairing
mode, it will automatically power off.
Pairing Process
While the UP5 is in pairing mode, turn on Bluetooth on your phone and search
for available Bluetooth devices. Click on “Shanling UP5” to finish pairing
process. If the pairing was successful, the display will show a currently used
Bluetooth codec.
Disconnection
- If the distance between the UP5 and the connected phone is beyond the effective connection range, the UP5 will show “RECONNECT” message and automatically power off after 10 minutes.
- If you manually turn off Bluetooth on the connected phone, the UP5 will automatically enter the pairing mode, display will show “PAIRING” and if no new phone is connected within 5 minutes, the UP5 will power off automatically.
Simultaneously Connecting Two Devices
- After pairing the UP5 with the fist phone, turn off Bluetooth on the first phone. Now pair the UP5 with the second phone.
- Turn on Bluetooth on the first phone and it can now connect to the UP5 simultaneously with the second phone.
Play / Pause
Press the [>Ⅱ ] button to pause or restart playback.
Next Track
Press the [>Ⅱ ] button twice to jump to the next track.
Previous Track
Press the [ >Ⅱ] button three times to jump to the previous track.
Answering Call
Press the multifunctional button once to answer the call.
Call Switch
During the call, quickly press the multifunctional button twice to switch the
call from the UP5 to the connected phone. Repeat to switch the call back to
the UP5.
Ending Call
Press the multifunctional button once to end the ongoing call.
Refusing Call
When a new call comes in, quickly press the multifunctional button twice to
refuse incoming call.
Volume Control
Turn the wheel clockwise to increase the volume or counter clockwise to
decrease the volume.
Menu Navigation
- Open menu: Long press the [>Ⅱ] button to open menu.
- Move to next setting: Press the multifunctional button.
- Adjust setting: Turn the volume wheel up or down.
- Exit menu: Long press the [ >Ⅱ] button to close menu.
USB DAC Function
UP5 supports both UAC1.0 and UAC2.0 standards.
UAC1.0: Simply connect the UP5 to the computer or other device. No additional
drivers are needed. Set the UP5 as the output device in sound settings.
UAC2.0: Install Shandling UP5 drivers on Windows computer. Set the UP5 as the
output device in sound settings.
Firmware Update / USB Driver
Visit the official website at en.shanling.com and go to the dedicated page of the UP5 to download the USB drivers and latest firmware.
Companion APP
Eddict Player app allows access to additional settings and control over UP5. You can download it from Play store or Apple Store.
Common Problems
- It is recommended to use DC5V 1A charger. Using a charger with higher voltage may damage the Shanling UP5.
- If the Shanling UP5 can’t be powered on, battery might be depleted. Please recharge it and try again.
- In the case of system freezing or crashing, please press and hold the Power button for 10 seconds to force a shutdown. To power on after forced shutdown, press and hold the Power button for 10 seconds.
- If there is noise from headphones, headphone’s connector may not be fully inserted, please try to insert it again.
- When there is no sound, try to use different pair of headphones or different cable and make sure the system volume is set correctly.
Attached Accessories
Quick start guide: 1
Warranty card: 1
USB-A to USB-C adapter: 1
USB Type-C to C cable1
Leather case1
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries.
MQA (Master Quality Authenticated) is an award-winning British technology that delivers the sound of the original master recording. The master MQA file is fully authenticated and is small enough to stream or download. The UP5 includes MQA technology, which enables you to play back MQA audio files and streams, delivering the sound of the original master recording. The UP5’s screen displays “MQA” to indicate that the unit is decoding and playing an MQA stream or file, and denotes provenance to ensure that the sound is identical to that of the source material. It displays “MQA” to indicate it is playing an MQA Studio file, which has either been approved in the studio by the artist/producer or has been verified by the copyright owner. Visit mqa.co.uk for more information. MQA and the Sound Wave Device are registered trade marks of MQA Limited © 2016
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try correct the interference by one or more of
the following measures:
– Reorient the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into and outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
The EUT is In door use
only.http://weixin.qq.com/r/f3RMVNrEsofNrZ439yFthttp://weibo.com/cnshanling
Company: Shenzhen Shanling Digital Technology
Development Co.,Ltd.
Address: No.10, Chiwan 1 Road, Shekou Nanshan
District of Shenzhen City, China.
QQ Group: 667914815; 303983891; 554058348
Telephone: 400-630-6778
E-mail: [email protected]
Official Website: www.shanling.com
Due to continuous improvement, every specification and design is subject to change at any time without further notice.