EZ Faucet Touch Free Faucet Adapter User Manual

Probnlem or Question? Call 1-800-660-7978

Package Contents:

|
---|---
|

KEEP INSTRUCTIONS FOR FUTURE REFERENCE

WARNING:Always turn water OFF before removing the existing faucet. Thank you for purchasing a quality EZ Faucet’• Touch-Free Sensor Adaptor. It will help conserve water and prevent the spreading of germs from cross-contamination. Please read all instructions before installation.

QUICK INSTALLATION GUIDE: (Please read all instructions before installation.)

1. Remove existing faucet aerator by turning counter-clockwise. Use the “Hexnut” Wrench, pliers, or vice grips if it is tight (Fit A).
2. After aerator is removed ensure that the rubber washer from the existing aerator is removed. If the washer is not in the lip of the existing aerator, it should be inside the water exit of the existing faucet.
3. Before installing the EZ Faucet, check if your faucet exit has Inside Thread (male adapter) or Outside Thread (female adaptor) type. Male adapter type: Insert the Rubber Washer that comes with the package into the Adaptor cm. co. Female adapter type: Do not use any rubber washer (Fit CM
4. Install EZ Faucet by turning the EZ Faucet Adaptor clockwise to attach to the faucet (first, use fingers to tighten, then use “Hexnut” Wrench me. in for final snug fit).
5. Remove EZ Faucet battery cover (see No.2 in Changing Battery section) and insert 4 new AAA Batteries (make sure batteries are inserted incorrect directions (+ and -) as indicated in the battery holder). Close the battery door firmly (Ft V.
6. Press and hold the Reset Button down for 3 seconds to adjust the sensor range automatically. EZ Faucet is ready for use after turning the faucet handles to ON position (adjust and check the water temperature properly before use —see Setting Water Temperature and Flow Rate section) WC O. If you have a problem with installation, please call 1.800.660.7978 or visit our website at http://www.ezfaucet.com.

Program the Sensor Range / Reset the EZ Faucet: WC E)

1. Turn the faucet handles to OFF position.
2. Press and hold the Reset Button for 3 seconds until the green light flashes and then release the button.
3. Wait until the green flashing light stops. Sensor range/E2 Faucet is set and ready for use after turning the faucet handles to ON position (adjust and check the water temperature properly before use — see Setting Water Temperature and Flow Rate section).
   Note : ll the sensor is too sensitive. try putting your hand 3–5″ below the sensor while programming the sensor range. This will shorten the sensor range.

Setting Water Temperature and Flow Rate;

1. Turn faucet handles to COLO position.
2. Press Manual Override Button once Ma g.
3. While the water is running, move existing faucet handles to adjust water temperature and flow rate.
4. Atter water temperature and now rate is set, press Manuel Override Button to turn off the water. The automatic feature is resumed.

Low Battery Indicator:

Best to use 4 Alkaline batteries with the same brand. they will last longer and keep EZ Faucet at the best performance. Approximately 1to 2 weeks before the power of batteries is out, the orange color POWER LOW indicator light will begin to flash. change all batteries as soon as possible. (see Changing Battery section).

Change Battery:

1. Turn the faucet handle to OFF position.
2. Remove the battery holder by pulling the battery holder out of the compartment
3. Take 4 batteries out one-by-one and replace new batteries (make sure to put batteries incorrect directions).
4. Close the battery holder by pushing the battery holder into the compartment until it is firm. Then adjust the sensor range (see Program the Sensor Range section).

Attention

1. Warning! Water may be HOT from last use! If you are not sure about the water temperature, always turn the faucet handles to COLD position (See Setting Water Temperature and Flow Rate section)
2. If water keeps running after installing the EZ Faucet for the first time, the control valve inside the EZ Faucet may be too dry. Let water run for 3 minutes and then turn the water off, After 20 minutes. press and hold the Reset button for 3 seconds to reset the E2 Faucet. (See Reset the EZ Faucet section). Turn the faucet handles to on position. The EZ Faucet is ready for use. If it fails, repeat the steps.
3. If water is leaking at the connection between the EZ Faucet and faucet head after installation. check if you put in the correct rubber washer (see No,3 in Quick Installation Guide and Troubleshooting FAOs sections).
4. Keep the EZ Faucet surface clean and dry. DO NOT WASH, clean with a damp towel. Never immerse the unit in water or any other liquid.
5. Make sure each battery is put in the correct direction.
6. Water stops flowing after 1 minute when an object is kept in the sensor area. BLOCK (green light) will flash signaling you to remove the object out of the sensor area.
7. Objects of dark color or transparent objects are not easily detected. Press Manual Override button to use manual operation when objects are not detected.
8. Do not obstruct water flow drainage when EZ Faucet is unattended. During the extended absence from the premise, best to turn the faucet handles to the ‘off” position (turn water tap off).
9. If the EZ Faucet keeps turning on by itself even after adjusting the sensor range manually (see Program the Sensor Range section). press and hold the Reset button for 3 seconds to reset the EZ Faucet.
10. If EZ Faucet malfunctions, press and hold the Reset button for 3 seconds to reset. If this fails, remove and reinsert all batteries to reset.

Troubleshooting Fiats:

Q : I test listened to the CZ Faucet and ready to use but the water mini and wen stop.
A : The control valve inside the  Faucet may be too dry Let realer run for 3 minutes and then turn the water Off. After 20 minutes. Dress and hold the Reset button fOr 3 seconds to reset the El Faucet: (See Reset the E2 Faucet section). Turn the faucet handles to ‘on’ aosibon. The El Faucet is ready for use. If it fads. repeat the steps to lubricate the control valve.
Q : Why WWI the EZ working? A: Always use 4 new AAA batteries with the same brand name (Alkaline battery preferred). Check all 4 batteries have been inserted facing the correct direction (. and -) as indicated in the battery holder. Also, check and ensure the batteries are snaffled into place.
A : I have attached the CZ Faucet to the faucet; however when I turn on the tap, water is spraying out at the connection. How do I fix this? A: You may have a DOW Connection d you hare no: used MC back lubber washer i5CC No 3 in Quick Ins: dilation Guide section) Remove the unit and try inserting the Rubber Washer. Every faucet is different so you may have to take some time to make the best adjustment lot yours. Tightening the Adaptor with “Ilesnur Wrench may also be needed.
Q : The El Faucet sensor Is too sensitive and even walking past the faucet will activate Ike water flow or the FZ Faucet keeps wales on by itself. Now do I adjust this?
A : You can adjust the detecting range of the sensor that activates the EZ Faucet. If your basin is shiny or the plug is bright silver color (almost likes mirror), the sensor will pick up movement off of these reflections. (see Program the Sensor Range sect,on).

Q: I am unable to remove the current rusting aerator from the faucet or I am unable to tighten the EZ faucet. What should I ea*
A : ‘ jou are basing millicuries removing the existing aerator, please lirs1 ensure that it actually can be remover]. Although this piece is removal:4e in all standard faucets, there may be a few that functions differently. Also check if you are removing in a correct direction (usually turning in counterclockwise). If the aerator is too tight, remote by (Fong the -klexnut• Wrench, pliers, 9r vice grips, Wrap a cling between the faucet #no 1994; this will ay9iO harmful scratches for which the manufacturer is not liable. To tighten the EZ Faucet, turn the EZ Faucet Heimut Adaptor clockwise by fingers first, and then snug firmly with the °Hesinur Wrench that Conies with package.

ONE (1) YEAR LIMITED WARRANTY (Valid for purchase within the USA and CANADA ONLY)

El faucet” distributed by iTouchless Housewares A Products. ix. (‘Toothless) with the highest quality compo-eats and most attached technology Breast. It as warranted to be free Iran defects in material and workmanship, given normal use ani care, lot 365 days from Me date el the °mina’ purchase wilt center of purchase within the United States and Canada, matchless hill city Mew warranty request from purchases. made from cur websites and authorized Wars, Hem’s soil as ust9,110cf satipEz, closeout or refurbished are sold softly under IN? terms and conditioner IN wiling catty. iTouchress will not Barrel the purchase. We witrepa r or replace the E/ Firer thereof each tail as 121 result ite ¶.):h a deti-et &fin? the warranty period
This warranty Is the customers’ erielusile remedy tar product detect and does not apply to:

• User modification
• Attachments to the product by the user that causes damage
• Pry product. or’ etch tt sears andi’v ma! hunters bars Wen broken, rerond, tamper% with, defaced Cir Vete*? ri any mires
• Darnagx caused by abuse. misuse. accident, water or Mel
• Ptroacai Damage Exi: ept as staled above. crotchless makes no morns and implied? wank as to arri product, in particular, makes no warranty Of merchantabllc1 or of fitness for any particular purpose. cleverness shall not be liable for consequential or exicier1.41 damages arising from any product defect. Our Liability is rimmed to my replacement of any defective Croix. touchless expressly disdain all resur4es, not sales tel n this funded warranty. Arty implied warranties that may be imposed by Ian are limited to the terms of this binned *termer H any pan spread Sad doing the warranty period. visit cot website at htlp://www.eziautet.com to reoxsi a Retake before returns:1g so us We Wit NOT ACCEPT package without the ReParer Berntinttr 10 return disciple FREIGHT PREPAID try an inert carrier such as UPS and 6:lude a disk ct USS9 95 lot return to six Erna USS10 00 should be added to return pitalape Allegro. Celina repaired the item to be shipptx1 to Canada tTotat USS19.95) We wit not pay fa any return postage to
  Subject to the above COndfialS, we will recoir or ship you a skin) El latter within 30 gherkins Mgt Eller ISO. INS warranty Mitt Su Wait for legal right, or you mar alto other reports that vary from It44f 19 $1010 3N province to prom me. Fte more information, please visit a.’ •etsile at MtplAwror ezfautel tom.

Return Andress: IToxibleas Housewares b PrOlY33 Inc. 23497 Fielder Shod, Unit A. Hayward, CA 94545 USA Ann: Product Return Repair.

Thank you for purchasing the I Touchless EZ Faucet'”!
Any Problem? DO NOT RETURN TO STORE. Call 1-800-660-7978 first.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>