dyson Vacuum Cleaner User Manual
- June 7, 2024
- dyson
Table of Contents
dyson Vacuum Cleaner User Manual
In the box
Getting started
Charging your machine
For the best experience, we recommend fully charging your machine, and any
additional batteries, as soon as you open the box and after every clean.
The LED light on the end of the handle will flash when the power is running
low and you need to put your battery on to charge. Connect the charger
directly to the charging point on the base of the handle of your machine. You
can also connect to your dock as shown in the installation instructions
supplied with your dock. The LED light on the end of the handle will pulse
with a blue LED light when charging, and the light will go out when fully
charged. It can take up to four hours to fully charge your battery. Your
battery has been designed to be left on charge. Your machine won’t operate or
charge if the ambient temperature is below 5°C (41°F). This is designed to
protect both the motor and battery. You can help prolong the battery life by
leaving your machine to cool down before recharging.
Caring for your floors
Check that the underside of the cleaner head or tool is clean and free from any objects that may cause damage. Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s recommended cleaning instructions. This machine is designed for use on hard floors. The brush bar on your machine can damage certain flooring. Some rug materials may fuzz if a rotating brush bar is used when vacuuming. If this happens, we recommend vacuuming without the motorized floor tool and consulting with your flooring manufacturer.
Emptying your bin
Empty your bin as soon as the dirt reaches the MAX mark. You may need to clean the filter more often if you use your machine with a full bin.
Remove your wand
Press the red wand release button, on the top of the wand, and pull the wand
away from the bin.
Release the dirt
Hold your vacuum over a bin. Push the red bin release button, taking care not
to press the power button. The bottom of the bin will open and the shroud will
slide down inside the bin, wiping away any dirt. If the bin doesn’t open,
check the bin release button is pushed down fully.
To remove the bin for emptying:
If the bin doesn’t empty fully, remove the bin and empty the dirt. Press the
red button located on the bin runner to release the bin and slide your bin off
the runner.
Minimize dust contact
Cover your bin tightly in a dust proof bag while you empty. Remove the bin
carefully, seal the bag tightly and dispose.
Reassemble your machine
If you have removed your bin, slide it back on to the runner. Make sure that
the bin and lid are both securely in position. Push the bin base upwards until
the bin and lid both click into place. Reconnect the wand.
Cleaning your bin
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Clean your bin If it is necessary to clean your bin, empty it as shown in the `Emptying your bin’ section. Press the red button located on the bin runner to release the bin and slide your bin off the runner. Only clean your bin with a damp cloth. Make sure that the bin and seals are completely dry before replacing. Replace your bin Insert the spine on to the bin runner. Close your bin by pushing the bin base upwards until the bin and bin base click into place.
Washing your filter
Wash your filter at least once a month to maintain the best performance. Make sure the filter is completely dry before refitting.
Twist off your filter
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Turn your filter anti-clockwise and pull it away from your machine. Before washing your filter, tap it gently over a bin to remove any loose dust and debris.
Wash your filter
Wash the outside of the filter, rubbing with your fingers to remove the dirt.
Carefully rinse the inside filter, without allowing water to fill the filter.
Repeat these steps until the water runs clear.
Shake and dry
Empty the filter and shake firmly to remove excess water. Keep shaking until
there’s no water coming from the filter. Place your filter end up, as shown.
Leave your filter to dry for at least 24 hours in a well-ventilated, warm
place. Don’t dry your filter in a tumble dryer, microwave or near a naked
flame. Important: your filter must be completely dry before you put it back
into the machine. Your machine could be damaged if used with a damp filter.
Refit your filter
To refit your filter, slide it onto the handle and turn it clockwise until it clicks into place. Your filter may need more frequent washing if you vacuum fine dust, use Max mode frequently or use with the bin full.
Washing your brush bar
To maintain optimum performance, check and wash the brush bar regularly.
Remove brush bar
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Press the cleaner head release button to remove it from the wand. Pull the brush bar off the end cap and put the end cap to one side, don’t wash it.
Wash and dry brush bar
Hold your brush bar under cold tap water and gently rub to remove any lint or
dirt. Keep washing until the water runs clear. Stand the brush bar upright and
leave for at least 24 hours to dry.
Replace your brush bars
Make sure your brush bar is completely dry before refitting. Reattach the end
cap to the brush bar and slide it back into the cleaner head. Rotate the end
cap until it clips securely back into position. The cleaner head housing is
not washable and should only be wiped over with a damp lint-free cloth.
Cleaning your tools
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Wipe with a damp, lint-free cloth, without touching the connector end. Make sure your tools are completely dry before using.
Clearing blockages
If your machine detects a blockage, the motor will pulse six times. You won’t
be able to use your machine until the blockage has been cleared. If you try to
use your machine when the motor is pulsing, it will automatically cut out.
Leave your machine to cool down before looking for blockages and, for your
safety, take care not to touch the power button.
Disconnect your machine from the charger before looking for blockages. Be
careful not to touch the trigger and be aware of sharp objects. Leave your
machine to cool down before looking for blockages. Don’t use your machine when
looking for blockages as this could cause injury.
Looking after your machine
To always get the best performance from your machine, it’s important to clean it regularly and check for blockages.
Look after your machine
If your machine is dusty, wipe with a damp lint-free cloth. Check for
blockages in the cleaner head, tools and main body of your machine. Wash your
filter regularly and leave to dry completely. Don’t use detergents or polishes
to clean your machine.
Look after your battery
To get the best performance and life from your battery, use Eco mode. Your
machine won’t operate or charge if the ambient temperature is below 5°C(41°F).
This is designed to protect both the motor and battery.
Your serial numbers You can register your machine using the serial number found on the bottom of your machine. You can find your serial numbers on your machine, battery and charger. Use your serial number to register.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>