EVERCROSS H5 Electric Scooter User Manual

H5 Electric Scooter
User Manual

Thank you for your choice, please read this manual before using this product.
Congratulations on your purchase of this new product.
When designing this electric car, I imagined a new world. In that world, it is an easy decision to leave your scooter behind!
During the design and development of our R & D team for many years, we focused on every detail. We want to make electric scooters a part of your life.
Enjoy, ride and go home safely.

PRODUCT DETAILS

WARNING AND SAFETY

Warning!
The responsibility for the repair and maintenance of the electric scooter is assigned to you, which can help you reduce the danger and injury. Reading this manual and following it will help you reduce the risk.

Be careful:

1. Be sure to comply with local traffic laws and regulations.
2. No riding in low visibility
3. Don’t use the car for stunts, wheels, or jumping movements, which will increase your chances of injury and damage to the car.
4. No passengers.
5. Make sure the safety catch and screws are locked and fastened before riding.

Devices are not intended for use at elevations greater than 2000 m above sea level Prolonged Exposure to UV Rays, Rain, and the Elements May Damage the Enclosure Materials, Store Indoors When Not in Use
WARNING — Risk of Fire — No User Serviceable Parts
AVERTISSEMENT- Risque d’incendie et de choc electrique – Aucune des pieces ne peut etre repartee par I’utilisateur

Safety instructions!

1. This product can only be used by one person. Do not carry others at the same time.

2. When riding this product, please wear a safety helmet. When riding, please hold the joystick with both hands correctly. It is forbidden to ride with one hand.

3. It is recommended to charge continuously for 6 hours before the first use to maintain the best condition.

4. Please contact in the open area now, and drive after being familiar with the operation of this product.

5. Do not ride this product on unsafe or illegal roads.

6. Do not turn off the power supply while the vehicle is moving.

7. Do not use this product in an environment lower than – 5 C. Please charge the lithium battery at least once every 30 days when it is not in use.

8. Keep your feet on the car when it’s moving.

9. Slow down and drive carefully when passing rough roads.

10. Do not ride on the ground with water, oil or ice on the surface.

11. Do not allow the product to be placed in a water depth of more than 5cm or directly impacted by water, which will cause motor and circuit faults.

12. WARNING — Risk of Fire — No User Serviceable Parts.
    AVERTISSEMENT – Risque d’incendie – Aucune des pieces ne peut etre reparee par l’utilisateur.

13. Unit is not intended for use at elevations greater than 2000 m above sea level.

14. Prolonged Exposure to UV Rays, Rain, and the Elements May Damage the Enclosure Materials, Store Indoors When Not in Use.

Tips:
When you want to accelerate, lean forward. When you brake, lean back!y

OPERATION GUIDE

Battery
Do not operate the motor while charging! The indicator light on the accelerator shows the power only roughly (full/empty)!
Do not store the battery fully charged for a long time (more than two months)!

Do not use the battery if:

1. When damaged
2. When abnormal smell and heat are released
3. When any leakage occurs
   Avoid contact with substances leaked from the battery.
   Batteries should be kept out of the reach of children and pets.
   Exposure to battery voltage can cause death or injury.

Using, storing, and charging the electric scooter outside the specified scope will lead to the invalidation of the warranty period, battery damage, and battery charging invalidity.

HOW TO CHARGE

1. Make sure the charging connector is clean and dry.
2. Start by plugging the charger into the product, then plug the switch into the power interface.
3. When the red indicator lights up on the charger, it means that the charging is carried out correctly.

GENERAL TROUBLESHOOTING

When the product cannot operate normally, please check whether the following actions have been completed:

1. Power on
2. The power display shows the remaining power
3. The brake has been released
4. All sockets and connectors are clean and connected accurately

If the above actions are completed and the single product still cannot operate normally, please consult the product dealer!!

POWER SWITCH AND KEY

Press the accelerator lightly to speed up the electric scooter.

LCD-JX168 INTELLIGENT SPEED CONTROL HANDLE INSTRUCTIONS (SPECIAL FOR

SCOOTER)

Version number: 2016020
Model number: JX-168
Working voltage: 8-80V compatible

Function:

1. Display function Speed display, battery indicator, fault indicator, headlight indicator, cruise indicator, gear indicator, total mileage, single mileage, real-time voltage, operating current, operating time, start mode
2. Communication protocol: UART
3. All contents of the display screen (full display within 1S after power on)

Display content introduction

1. Voltage status level POWER

2. Multifunctional display area
   Total mileage ODO, Single mileage TRIP, Real-time Voltage V, Running current A, Running time TIME, Fault code E

3. In the fault status display area E, when the symbol n is flashing, short press the ON/OFF key to adjust the display interface to the E interface. The corresponding number under this interface represents the corresponding fault content. The specific status is as follows
   ERRO 1. Motor HAL status
   ERRO 2. Brake failure
   ERRO 6. Undervoltage
   ERRO 7. Motor failure
   ERRO 8. Handlebar malfunction
   ERRO 9. Controller failure
   ERRO 10. Receiving time has timed out
   ERRO 11. Sending failure

4. Speed display area
   Unit MPH, KM/H

5. Gear display area
   Press the MODE button shortly to switch the gears cyclically.
   The higher the gear, the faster the speed. The motor will not run at gear 0

6. Decorative lights display area Long press the MODE button, and the decorative lights symbol light up

7. Cruise display area
   After the motor is running, keep the speed control handle for 5 seconds and the cruise symbol is on. After releasing the handle, the motor keeps running at the original speed, brake, or turn the speed control handle again and return it to the cruise state.

8. Startup method to select the display area
   Non-zero start: NONsymbol lights up Zero starts: ZERO symbol lights up

9. USB charging icon display area
   When a data cable is connected to the USB interface of the instrument and draws more than 100 mA of current from it, the USB icon lights up. If the icon is flashing, it means the load is in intermittent charging or the load current exceeds 500 mA, and the USB interface automatically turns on protection mode

10. Parameter setting and definition
    P02: Mileage unit, 0: KM; 1: MILE;
    PO4: Sleep time: 0, no sleep; other numbers are sleep time, range: 1-60; unit minute;
    P09: Zero start, non-zero start setting, 0: zero start; 1: non-zero start;
    P16: Instrument real-time cruise function 1 With this function 0 Without this function
    P99: One-key recovery function (in the P99 parameter setting interface, press and hold the
    MODE button for 5-6 seconds and all parameters are restored to the initial settings of the first startup)
    ODO: ODO clear (in the ODO parameter setting interface, first short press the MODE button and then long press for 5M-6 seconds until the number is zero and release)

2. Brief introduction of key functions:
2.1 In the shutdown state, press and hold the power button to turn on, after turning on, press the power button shortly, and the interface will switch between ODO, TRIP, V, A, E, TM,
2.2 In the power-on state, press and hold the power button to power off.
2.3 Long press the M key and the power key to enter the mode setting. In the setting interface, short press the power key to switch parameters; Short press the M button to change the state of the vehicle speed, the gear shifts from 0 to the highest gear cyclically The gears default to 1 gear, 0 gears motor does not run, 3 gears have the highest speed Parameter value modification: Enter the parameter setting to meet, adjust to the parameter you want to adjust, and press the power button and M button to increase Increase or decrease the parameter value, after confirming that the modification is completed, long press the power button and M button to exit the parameter setting, and the parameter modification will be completed after power off and restart.
2.4 The rocker’s arm adjusts the motor speed, moving from top to bottom, the motor speed increases; let go and return to the zero position.

PRODUCT PARAMETERS

3 months:-20 – 45 C
1 year: -20 – 20 C
Minimum Ride Weight:|  120 lbs

STORAGE AND DISPOSAL

• Before storage, fully charge the electric scooter to prevent battery over-discharge due to it’s not used for a long time.
• If the storage time is more than a few months, please charge it once a month.
• Do not charge the scooter if the storage temperature is below 0 degrees Celsius. You can charge it in a warm environment (above 10 degrees Celsius).
• You can mask the scooter to prevent dust from affecting its performance.
• Keep store the scooter indoors and put it in a place with dry air and a suitable temperature.

TEMPERATURE LIMIT

CHARGER INFORMATION (SPECIFIC MANUFACTURER MODEL)

Model: GJS150-0541830 Input: AC100-240V-50/60Hz Max.3.0A Output: DC 54.6V-2.0A Manufacturer: Shenzhen Gojusin Technology Co., Ltd Add: Block B, No.28 Lianhe industrial Zone of First Area Nanyue Community Longgang District Shenzhen, Guangdong

MAINTENANCE CONTACT INFORMATION:

We provide warranty service and lifetime after-sales consulting service for each self-balancing scooter. Please contact our Amazon aftersales service when you encounter any problems during your use, we will answer you as soon as possible to help you solve the problem. Email:support@evercross.eu Website: https://www.evercross.eu/

https://www.LikeSporting.com

References

• Likesporting-Treadmills,walking machines,elliptical machines and other fitness equipment mall-Likesporting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>