FLUKE networks FI-7000 FiberInspector Pro Datasheet

June 7, 2024
FLUKE networks

DATASHEET
FI-7000 FiberInspector™ Pro

At a Glance
Roughly 85% of fiber optic network failures are due to contaminated end-faces. While inspecting and cleaning end faces and connectors is not new, it is growing in importance and linked with increasing data rates which impact budgets. Fluke Networks’ FI-7000 FiberInspector Pro allows you to inspect and certify end-faces in 2 seconds so you can get the job done the first time.
Automated PASS/FAIL certification takes the guesswork out of fiber inspection so anyone can be a fiber expert.

FLUKE networks FI-7000 FiberInspector Pro -

Eliminate the #1 cause of fiber failure
End-face contamination is a leading cause of fiber failures. Dirt and contaminants cause insertion loss and back-reflection that inhibits optical transmission and causes havoc with transceivers. Fiber loss and OTDR testing can expose this problem, but in many cases, dirty connections make fiber testing time-consuming and inaccurate. Since dirt can be an issue before, during, or after fiber optic certification testing, and migrate from one end- face to another upon mating, both sides of any connection must always be cleaned and inspected. Further, mating contaminated connectors can cause permanent damage as microscopic debris is crushed between end-faces in physical contact. Even factory terminated patch cords or pigtails must be inspected as protective caps do not keep end-faces clean. Avoiding this common cause of failure starts with inspecting the end-face and eliminating any contamination before insertion into a bulkhead or piece of equipment.

Overview

The FI-7000 FiberInspector Pro enables you to quickly inspect and certify fiber end-faces inside ports or patch cords. Its 2second automated PASS/FAIL certification eliminates human subjectivity and enables anyone to become a fiber inspection expert.
Automated Pass/Fail acceptance testing of fiber  end-faces Graphical indication of  problem areas due to  contamination, pits,  chips, and
scratches Large touchscreen for pinch and zoom  Certify to industry standards –  DEC 61300-3-35 No  more confusion  about whether the fiber is good or bad Eliminate human subjectivity from  end-face measurements Save end-face  views during certification  process Reduce fiber inspection time with 2-second grading ProjX™ system manages job requirements and progress from  set-up to systems acceptance, making sure all tests are  completed correctly Taptive™ user interface  simplifies set-up, and eliminates error  Analyze test results and create professional test  reports using LinkWare™ management software Integrated Wi-Fi allows you to easily upload results to LinkWare Live

Fiber Inspection Certification

Certify your fiber end-faces to industry standards – IEC 61300-3-35. Or if you prefer, you can manually grade your end-faces.

FLUKE networks FI-7000 FiberInspector Pro -
Certification

Store End-face Images
Store both end-face images of a fiber directly in your Versiv test results. Combine end-face images with CertiFiber Pro OLTS and/or OptiFiber Pro OTDR test results for the complete history of your fiber cabling health.

Built on the Versiv Platform

The FI-7000 is built on the Versiv Cable Certification Platform which enables you to easily add optical loss (OLTS) and Optical Time Domain Reflectometry (OTDR) or even twisted pair copper or network analysis functionality to FI-7000. Product add-on kits are available for the DTX CableAnalyzer, CertiFiber Pro OLTS, OptiFiber Pro OTDR, and OneTouch AT Network Assistant.

Versiv’s ProjX System
ProjX manages jobs from setup to systems acceptance, ensuring that all tests are completed correctly. Enter the testing details for a job once, and ProjX stores them in a project file with a name the whole team can understand. Change modules or jobs without having to re-enter details. Support multiple testers on the same job by sharing project files via USB sticks or email.

Taptive User Interface
Now you can test across multiple media types and requirements as easily as using a smartphone. Simply, select the job you’re working on, and the large display confirms the test that needs to be performed. Captive helps you tap into the overall cabling infrastructure faster and more easily.

LinkWare Management System
Leveraging the popular and multi-featured LinkWare management software application, FI-7000 FiberInspector Pro users can easily access the ProjX management system data, generate reports, and upgrade the software in their testers. Project Managers have full capabilities to manage workflow and consolidate test results. Users can provide the finishing touch by adding their company logo to the report and offer it unaltered to their customers for system acceptance purposes. Keep your business tools simple, no matter which Fluke Networks copper or fiber tester you are using, LinkWare is the software package that reports it all.

PASS/FAIL Fiber End-face Grading
The FI-7000’s PASS/FAIL fiber end-face grading is available to all Versiv owners. It is included in Versiv firmware v3.0 and higher. To enjoy this free fiber end-face grading, just download the latest Versiv firmware and create a new Project using FiberInspector as the test.

FLUKE networks FI-7000 FiberInspector Pro - End-face
Grading

Technical Specifications

Inspection Probe specifications

Resolution| 2M pixels
Light Source| Blue LED
Power Source| Versiv mainframe
Field of View (FOV)| Horizontal: 425 pm, Vertical: 320 pm
Minimum Detectable Particle Size| 0.5 pm
Dimensions| Approximately 6.75 in x 1.5 in (1175 mm x 35 mm) without adapter tip
Weight| 200 g
Temperature Range| Operating: 32° F to 122° F (0 °C to +50° C), Storage: -4° F to +158° F (-20° C to +70° C)
Certifications| CE

General Specifications

Weight| Mainframe with module and battery: 3 lbs, 5 oz (1.28 kg)
Dimensions| Mainframe with module and battery: 2.625 in x 5.25 in x 11.0 in ( 6.67 cm x 13.33 cm x 27.94 cm)
Battery| Lithium-ion battery pack, 7.2 volts
Battery Life| Eleven hours with Inspection probe attached
Integrated Wi-Fi| Meets IEEE 802.11 a/b/g/n; dual-band (2.4 GHz and 5 GHz)

Environmental Specifications

Operating Temperature*| -18° C to 45° C
Non-operating Temperature| -30° C to 60° C
Operating Altitude| 4,000 m (13123 ft) 3200 m (10,500 ft) with ac adapter
Storage Altitude| 12,000 m
EMC| EN 61326-1

  • Do not keep the battery at temperatures below -20° C (-4° F) or above 50° C (122° F) for periods longer than one week to maintain battery capacity.

Ordering Information

FI-7000 Wireless models

Model| Description
FI2-7000| FiberInspector Pro V2, with Wi-Fi
FI2-7000-MPO| FiberInspector Pro V2 with MPO tip, cleaning and Wi-Fi

FI-7000 Pro Non-Wireless models

Model| Description
FI2-7000-NW| FiberInspector Pro V2
FI2-7000-MPO-NW| FiberInspector Pro V2 with MPO tip, cleaning

Model Description
Fl-1000 USB video probe for Versiv products
FI.1000- KIT USB video probe for Versiv products plus tip set (LC, FC/SC

BULKHEAD, 1.25 AND 2.5 mm UNIVERSAL TIPS in a box)
FI1000-TIP-KIT| bulkhead, 1.25 AND 2.5 mm universal tips in a box
F11000-ST- TIP| ST bulkhead video probe tip
FI1000-
MU-TIP| MU bulkhead video probe tip
FI1000- E2KAPC- TIP| E2000/APC bulkhead video probe tip
FI1000- SCAPC-TIP| SC/APC bulkhead video probe tip
FI1000- E2K-TIP| E2000 bulkhead video probe tip
FI1000- LCAPC-TIP| LC/APC bulkhead video probe tip
FI1000-2.5- UTIP| 2.5 mm universal video probe tip for patch cords
FI1000- 1.25-TIP| 1.25 mm universal video probe tip for patch cords ‘
FI1000- 2.5APC- UTIP| 2.5 mm APC universal video probe tip for patch cord
FI1000- MPO-UP| MPO probe tip and translator knob for patch cords and bulkheads
FI1000-
MPO-XY-
UP| MPO probe tip and translator knob for multi-row patch cords and bulkheads
FI1000- MPOAPC- UTIP| MPO/APC probe tip and translator knob for patch cords and bulkheads
---|---
FI1000- 1.25APC- TIP| 1.25 mm APC universal video probe tip for patch cords
FI1000- MPOAPC- RT| MPO/MTP APC REPLACEMENT TIP WITH NO TRANSLATOR KNOB
FI1000- MPO-RT| MPO/MTP REPLACEMENT TIP WITH NO TRANSLATOR KNOB
NFC-KIT- CASE-E| Enhanced Fiber Optic Cleaning Kit — Includes an IBC OneClick 1.25mm cleaner, an IBC OneClick 2.5 mm cleaner, an IBC OneClick MPO cleaner, a solvent pen, a cleaning cube and a softcase
VERSIVSM-CASE| Versiv Small Carry Case

FI-7000 Gold Support models

Model| Description
GLD-FI-7000| 1 year Gold Support, FI2-7000 or FI-7000
GLD3-FI-7000| 3 year Gold Support, FI2-7000 or FI-7000
GLD-FI-7000-MPO| 1 year Gold Support, FI2-7000-MPO or FI-7000-MPO
GLD3-FI-7000-MPO| 3 year Gold Support, FI2-7000-MPO or FI-7000-MPO

About Fluke Networks

Fluke Networks is the worldwide leader in certification, troubleshooting, and installation tools for professionals who install and maintain critical network cabling infrastructure. From installing the most advanced data centers to restoring service in the worst weather, our combination of legendary reliability and unmatched performance ensure jobs are done efficiently. The company’s flagship products include the innovative LinkWare™ Live, the world’s leading cloud-connected cable certification solution with over fourteen million results uploaded to date.
1-800-283-5853 (US & Canada)
1-425-446-5500 (International)
http://www.flukenetworks.com
Descriptions, information, and viability of the information contained in this document are subject to change without notice.
Revised: November 15, 2019 7:43 AM
Literature ID: 6002482
© Fluke Networks 2018

FI-7000 FiberInspector™ Pro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals