HIKVISION DS-PS1-E-WB Wireless External Sounder User Manual

DS-PS1-E-WB Wireless
External Sounder
50131-1:2006+A2:2017
50131-4:2019
**50131-5-3:2017
Security Grade(SG) 2
Environmental Class(EC) IV Certified by Telefication

**

Appearance

Indication

LED Indication Description
Operations

Display Signal Strength
Check signal strength and select installation place
Enter the signal checking mode by operating on the AX PRO.

Buzzer

Note:
-You can sign in to web client “Device – Sounder – Settings” or the mobile client “wireless Device” to adjust the volume of the buzzer.
-The zone alarm buzzer in volume level 3 complaints with EN certification.

Power On

1. Loosen the set screw at the bottom of the sounder and remove the front panel.
   Note: You can hang the front panel on the buckle.
   

2. Open the water-proof cover.
   |
   ---|---

3. Power the sounder on.

Battery Power
1. Install four CR123A batteries according to the polarity mark.
Note: The batteries are included by default.
2. Close the water-proof cover.
3. Push the power switch to ON.| 12 VDC Power
1. Push the Cable Knock-Out away.
2. Wire the power cable.
3. Close the water-proof cover.
4. Push the power switch to ON.
Note: The 12 VDC power supply is non
EN compliant.
---|---
|
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

CHEMICAL BURNING DANGER DO NOT SWALLOW THE BATTERY KEEP NEW AND USED BATTERIES AWAY FROM THE CHILDREN
INSTALL THE BATTERIES ACCORDING TO THE POLARITY MARK ON THE BATTERY HOLDER. THE OPPOSITE POLARITY MAY CAUSE DEVICE DAMAGE
DO NOT REVERSE THE POLARITY OF THE BATTERY

Note: For power on again, push the power switch to ON at least 5 s after power off.

Enrollment

1. Log in to the APP Store, download, and install App.
2. Power on the security control panel.
3. Log in to the APP and tap the icon “+”. Scan the QR code or input the control panel serial No. (Last 5 digit) to add the control panel.
4. Enroll the peripheral locally, with OR code, or with serial No..

Enroll the Peripheral Locally

1. In the APP, tap the “Enrollment Mode” button on the control panel page to make the control panel enter the enrollment status.
2. Push the power switch of the peripheral to on, and it will be automatically enrolled to the control panel.

Enroll the Peripheral with APP

1. In the APP, tap the icon “+” and scan the QR code on the peripheral or enter the serial No. (Last 5 digits) of the peripheral.
2. Push the power switch of the peripheral to on, and it will be automatically enrolled to the control panel.

Note: for re-enrollment, you need to hold the tamper button while powering the peripheral on simultaneously.

Installation

-The additional force shall be equal to three times the weight of the equipment but not less than 50N. The equipment and its associated mounting means shall remain secure during the installation. After the installation, the equipment, including any associated mounting plate, shall not be damaged.
-Install the device in a place with nonflammable surfaces, such as a concrete wall.

1. Check signal strength and select installation place
Enter the signal checking mode by operating on the control panel.
The signal indicator turns green for 3 s: Strong.
The signal indicator turns orange for 3 s: Medium.
The signal indicator turns red for 3 s: Weak.
Signal indicator flashes red for 3 s: Lost.

2. Loosen the set screw at the bottom of the sounder and remove the front panel.
Note: You can hang the front panel on the buckle.|
---|---
3. Attach the sounder to the required place with the top screw. Make the sounder horizontal by resorting to the gradient.|
4. Secure the sounder with the other three screws.|
5. Fix the front panel on the sounder body. Tighten the set screw to complete the installation.|

Operation

Formatting
Hold the tamper button, and push the power switch to ON simultaneously. Release the tamper button after 8 s, and the device will starts formatting. While the formatting is completed, the red LED flashes 3 times.

 Operation Caution and Device Maintenance

– All the electronic operations should be in strict compliance with the electrical safety regulations, fire prevention regulations, and other related regulations in your
local region.
– Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations
surface or places subject to shock (ignorance can cause equipment damage).
– Please make sure that the power has been disconnected before you wire, install or dismantle the device.
– If smoke, odors, or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
– Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surfaces or places subject to shock (ignorance can cause equipment damage).
– Do not place the device in extremely hot (refer to the specification of the device for the detailed operation temperature), cold, dusty, or damp locations, and do not expose it to high electromagnetic radiation. Exposing the equipment to direct sun light, low ventilation, or heat sources such as heater or radiator is forbidden
(ignorance cause fire danger).
– Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction, however), and affecting the
endurance of the sensor at the same time.
– Improper use or replacement of the battery may result in a hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
– Do not expose the device to corrosive gas. Otherwise, the equipment damage may occur.
– Do not expose the device to the explosive situation.

Specification

Battery: Max. 3 V/4A (alerts in volume level 3 )

12 VDC: Max. 12 V/1.3A (alerts in volume level 3 )

Low Battery Cut Off| 2.45 V
Voltage Range| Fully charged (new) to 2.45V DC (battery)
Battery life span| 4 CR123A, 3 years in work status(triggered every two weeks and alerting 90 s for each triggering)
Interface| Power switch| Power switch
Tamper switch| Front and rear tamper-proof
Buzzer| Piezo Decibel| 102 dB
Max. Sound Duration| 15min (900s)
General| Operation Temperature| -25 °C to 60 °C (-13 °F to 140 °F)
Operation Humidity| 10% to 90%
Material| PC+ABS
Dimension (W x H x D)| 190x 200 x 47. 3mm .(7.48″ x7.87″ x 1.86″ )
Weight| 606.5g
Protection Level| IP65
Installation| Wall mounting

and other Hikvision trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.

Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE, AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE, OR OTHER DAMAGES RESULTING FROM
CYBER-ATTACKS, HACKER ATTACKS, VIRUS INSPECTIONS, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU
SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.

©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images, and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change,
without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https://www.hikvision.com/).
Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.

This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
– disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
– leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and
– a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:www.recyclethis.info

Hangzhou Hikvision Digital Technology CO., Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China

References

• HOME
• Hikvision - Leading Video AIoT Solutions & Services Provider

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>