HIKVISION DS-KV8X13-M Video Intercom Villa Door Station User Guide
- June 7, 2024
- Hikvision
Table of Contents
DS-KV8X13-M
Video Intercom Villa Door Station
UD16093B-B
Diagram References
Appearance
- Microphone
- Indicator
- Camera
- Loudspeaker
- Button
- Card Reader Area
- IR Light
- Micro SD Card Slot & Debugging Port
- LAN
- Terminals
Note: Debugging port is used for debugging only.
Indicator Description
Unlock: Green
Call: Orange
Communicate: White
Terminal and Wiring
NC: Door Lock Relay Output (NC)
AIN1: For access to Door Contact
AIN2 & AIN4: Reserved
485-: RS-485 Interface (Reserved)
12 VDC IN: Power Supply Input
LAN: Network Interface
NO: Door Lock Relay Output (NO) COM: Common Interface
AIN3: For the access of Exit Button
485+: RS-485 Interface (Reserved)
GND: Grounding
Installation Accessory
- Mounting Template
- Mounting Plate
Note: The dimension of the mounting plate is 174 mm × 83.66 mm × 18 mm.
Installation
Note: Video intercom villa door station supports flush mounting and surface
mounting.
Before you begin:
- Make sure all related equipment is power-off during the installation.
- Tools that you need to prepare for installation: Drill (ø2.846) and gradienter.
- Purchase the protective shield before installation.
Surface Mounting without Protective Shield
-
Stick the mounting template on the wall. Drill screw holes according to the mounting template.
Remove the template from the wall. -
Secure the mounting plate on the wall with 4 supplied screws according to the screw holes.
-
Secure the device on the mounting plate with 4 supplied set screws.
-
Fix the cover onto the device with the screw.
Surface Mounting with Protective Shield
-
Stick the mounting template on the wall. Drill screw holes according to the mounting template.
Remove the template from the wall. -
Align the protective shield with the mounting template.
-
Secure the mounting plate on the wall with 4 supplied screws according to the screw holes.
-
Secure the device on the mounting plate with 4 supplied set screws.
-
Fix the cover onto the device with the screw.
Flush Mounting without Protective Shield
-
Stick the mounting template on the wall. Drill the hole according to the mounting template.
Remove the template from the wall.
Note: The suggested size of the hole is 175 mm × 84 mm × 19 mm. -
Install the gang box into the hole with 4 screws.
-
Insert the device into the gang box. Secure the device with 4 supplied screws.
-
Fix the cover onto the device with the screw.
Flush Mounting with Protective Shield
-
Stick the mounting template on the wall. Drill the hole according to the mounting template.
Remove the template from the wall.
Note: The suggested size of the hole is 175 mm × 84 mm × 19 mm. -
Install the gang box into the hole with 4 screws.
-
Align the protective shield with the gang box.
-
Insert the device into the gang box. Secure the device with 4 supplied screws.
-
Fix the cover onto the device with the screw.
Configuration via Web
Activate Device via Web
You are required to activate the device first by setting a strong password for
it before you can use the device.
Default parameters of door station are as follows:
• Default IP Address: 192.0.0.65.
• Default Port No.: 8000.
• Default User Name: admin.
-
Power on the device, and connect the device to the network.
-
Enter the IP address into the address bar of the web browser, and click Enter to enter the activation page.
Note: The computer and the device should belong to the same subnet. -
Create and enter a password into the password field.
-
Confirm the password.
-
Click OK to activate the device.
Note: When the device is not activated, the basic operation and remote configuration of the device cannot be performed.
Access to the Device by Web Browsers -
In the browser address bar, enter the IP address of the device, and press the Enter key to enter the login page.
-
Enter the user name and password and click Login.
Communicate with Indoor Station
Note Configure room No. of the indoor station which is linked to the villa door station. Refer to Video Intercom Indoor Station User Manual for details.
-
Click Settings → Intercom → Press Button to Call to enter the settings page.
-
Set the parameters.
-Edit call No. for every button.
-Check Call Management Center to set the button calling center.
Note: If you check Call Management Center and set the call No. as well, the call management center has a higher privilege than calling No. -
Press the button to call the indoor station.
Issue Card
- Click Settings → Access Control and Elevator Control to enter the corresponding settings page.
- Click Issue Card. Present the card in the card reading area.
- When issuing finished, the windows pop up on the settings page.
• Only Mifare card supported, and Mifare card with non-standard shape is recommended.
• Up to 10000 cards can be issued and managed by the V series door station. A voice prompt (No more cards can be issued.) can be heard when the issued card amount exceeds the upper limit.
Unlock Door
After issuing cards, you can unlock the door by presenting the issued
card.
Refer to Video Intercom Villa Door Station User Manual (scan the QR code) for
details.
http://enpinfodata.hikvision.com/analysisQR/showQR/019f0fbc
Product Information
©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instructions on how to use the Product. The software embodied in
the Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection.
Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all
rights to this manual. This manual cannot be reproduced, changed, translated,
or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered
trademarks or the subject of applications for the same by Hikvision and/or its
affiliates. Other trademarks mentioned in this manual are the properties of
their respective owners. No right or license is given to use such trademarks
without express permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH
ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND
ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR
ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG
OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS
OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING THE PRODUCT WITH INTERNET ACCESS, THE USE OF THE PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISK. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITY FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE, OR OTHER DAMAGES RESULTING FROM CYBER
ATTACKS, HACKER ATTACKS, VIRUS INSPECTIONS, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE
CONFORMS TO THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED FOR ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATTER PREVAILS.
Data Protection
During the use of the device, personal data will be collected, stored, and
processed. To protect data, the development of Hikvision devices incorporates
privacy by design principles. For example, for a device with facial
recognition features, biometrics data is stored in your device with encryption
method; for fingerprint device, only fingerprint template will be saved, which
is impossible to reconstruct a fingerprint image.
As a data controller, you are advised to collect, store, process, and transfer
data in accordance with the applicable data protection laws and regulations,
including without limitation, conducting security controls to safeguard
personal data, such as, implementing reasonable administrative and physical
security controls, conduct periodic reviews and assessments of the
effectiveness of your security controls.
FCC Information
Please take attention that changes or modification not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC compliance: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm
between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new
equipment, or dispose of it at designated collection points. For more
information see: www.recyclethis.info
IC statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>