PRESTIGE APS510Z Security with Keyless Entry User Guide
- June 6, 2024
- PRESTIGE
Table of Contents
APS510Z
Security with Keyless Entry
Quick Installation Guide
Alarm
When the alarm is triggered the system will provide feedback to the user. Upon disarm, the system will beep four (4) times and flash the LED to indicate the Alarm Trigger Zone.
1 | Shock |
---|---|
2 | Trunk/Hood |
3 | Door |
Chirp Delete
System ARM/DISARM chirps can be toggled ON or OFF without entering the Feature Bank programming.
- Turn the ignition key ON/OFF.
- Press and release the valet button three (3) times.
The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This feature will not affect alarm triggers or programming.
User Programmable LED
System LED notifications can be turned ON or OFF without entering
Feature Bank programming.
- Turn the ignition key ON/OFF, ON/OFF.
- Press and hold the valet button for five (5) seconds.
The LED will flash one (1) time for ON, two (2) times for OFF. This feature will not affect LED flash during programming.
Remote Programming
The APS510Z includes two (2) programmed remotes. If required, additional
remotes can be programmed into the system. Remote
Programming is located in Feature Bank 1. To enter Remote Auto Programming:
- Turn the ignition key on ON.
- Press and release the valet button three (3) times. System will chirp and flash the parking lights one (1) time.
Press the lock button on each remote. The system will beep one (1)time to indicate the remote has been programmed. Only primary remote functions are auto-programmed. This Includes Lock, Unlock, and
Trunk/Start.
If using the AUX output control, the remote channel must be manually programmed to the system AUX output. Please see the complete
installation guide for manual remote programming instruction.
Feature Programming
The APS510Z Feature Bank can be programmed by using the valet button and remote. To enter Feature Bank programming:
-
Turn the ignition key on ON.
-
Press and release the valet button three (3) times. System will chirp and flashlights one (1) time for Feature Bank 1, Remote
Programming. -
Cycle ignition key OFF/ON. The system will chirp and flashlights two (2) times for Feature Bank 2.
-
Press the valet button to cycle features. LED will flash to display the feature number.
-
Press the lock button to cycle options. The system will chirp to indicate the option number.
To exit the Programming cycle ignition key OFF and wait ten (10) seconds.
The System will also automatically exit programming after sixty (60) seconds
of no activity.
Dome Delay Programming
This system can be programmed to ignore the vehicle’s theater dimming dome
light. This feature will be used when connecting the door trigger input to the
dome light circuit for the alarm trigger. Note: Vehicle windows should be open
to prevent accidental locking of keys in the vehicle.
Start with all doors closed and the vehicle dome light off.
- Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light solid.
- Open and close the driver’s door.
The system will monitor the dome light circuit. When the dome light turns off the system will set the delay time and add an additional two (2) seconds.
Dome Delay Reset
- Key ON/OFF, ON/OFF, ON/OFF.
- Press and hold the valet button for five (5) seconds.
The system will chirp one (1) time to indicate reset is complete.
Shock Sensor
The shock sensor should be mounted to a solid surface in the center of the
vehicle. Once mounted the shock sensor will require adjustment.
To increase sensitivity: Turn adjustment dial clockwise.
To decrease sensitivity: Turn the adjustment dial counterclockwise.
To test sensitivity, strike the vehicle with an open palm. Adjust the dial to
provide coverage to as much of the vehicle as possible.
The Feature Bank below can also be programmed using the FlashLogic Weblink.
Please visit www.FlashLogic.com for more detail.
Feature Bank 2
|
Options
---|---
1 Chirp| 2 Chirp| 3 Chirp| 4 Chirp| 5 Chirp| 6 Chirp
I Features I| 1| Lock / Unlock Function| 50Orns| 3.5sec| SOOms I., DBL
UL| DBL L, SOOms UL| DBL L, DBL UL| SOOms I., 35Orns UL
2| Ignition Lock| OFF| ON| | | |
3| Ignition Unlock| OFF| Unlock All| Unlock Driver| | |
4| Exterior Illumination| OFF| With Arm| With Disarm| With Arm &
Disarm| |
5| Auto Relock| OFF| Auto-Lock| Auto-Lock & Arm| | |
6| Auto Arming| OFF| Auto Arm| Auto-Lock & Arm| | |
7| Notification Sound| Both| Siren| Horn| | |
8| Horn Tuning| 16ms| 30ms| 40ms| SOms| 10ms|
9| Valet Override Method| Valet| Custom Code| | | |
10| Driver Priority Unlock| OFF| ON| | | |
11| Silent Choice| OFF| From Transmitter| OEM Style| | |
12| Park Light/ Trunk Swap| NA| | | | |
13| AUX Ch. 4| Pulse| Push & Hold| lOsec| 20sec| Latch On/Off| Hold 3/s
for 0/P
14| AUX Ch. 5| Pulse| Push & Hold| lOsec| 20sec| Latch On/Off| Hold 3/s
for 0/P
15| Alarm Trigger Length| 30sec| 45sec| 60sec| 90sec| 120sec|
16| Dome Light Delay Timer| Off/Program| 15sec| 30sec| 45sec| 60sec|
120sec
17| Security Profile| All On| Doors Off| Hood/trunk Off| All Off| All On
w/ OEM RS|
18| Data Port Protocol| ADS| DBI| | | |
Important Update
The default Data Port Protocol of this system is ADS. If using a FLCAN or
other external integration module be sure to choose iDatalink
2-Way when flashing.
This system will also support DBI. This will require programming Feature Bank
2, Feature 18 to DBI.
Data Protocol Selection
The default data port protocol of this model is ADS (iDatalink 2-Way).
This model is capable of detecting the correct data port protocol (ADS or DBI)
and automatically configuring Feature Bank 2; Feature 18. To initialize the
detection procedure:
- Press and hold the valet button.
- Cycle the vehicle’s Ignition ON/OFF two (2) times.
- Release the valet button.
The system will automatically detect and set the correct data port protocol,
ADS or DBI.
Note: This feature is only available on module firmware v2.00 or higher.
For Complete Installation Guide and Technical Support
Please visit
www.voxxuniversity.com
Or Call
1-800-225-6074
REV. B
2020 Voxx Electronics. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>