Mambot W120-T iGLASSBOT Robot Window Cleaner User Manual
- June 6, 2024
- Mambot
Table of Contents
The expert for robots in your home
With one click to the online shop
myRobotcenter.eu|
myRobotcenter.co.uk
---|---
Mamibot
W120-T iGLASSBOTTm
Robot Window Cleaner
USER MANUAL
V.20181010
All rights reserved by Mamibot, subject to change without notice.
Important Safety Instructions and Warning
Note! – Read all documents before using
The appliance is not to be used by children. Persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge may only use this appliance if they are supervised or have been given instruction about how to use it safely and understand what risks are involved. Children should be supervised to ensure they do not play with the robot.
!!! The appliance is for window cleaning with frames (frameless glass/window cleaning is not applicable). Users should judge and use it safely on proper operation sites, and be responsible for all possible consequences.
Safety Information
- Application of Power Adatper and Batteries Use only the power adapter supplied with this device. Use of another type of power adapter will result in malfunction and/or danger.
- Please use the proper electric outlet and make sure no heavy objects are placed on the power adapter or power cord.
- Allow adequate ventilation around the adapter when using it to operate the device. Do not cover the power adapter with objects that will reduce cooling. Do not use the adapter in a high moisture environment. Never handle the adapter with wet hands.
- Connect the adapter to a proper power source. The voltage requirements are found on the adapter.
- Do not use a broken adapter, power cord, or plug. The plug must be removed from the receptacle before cleaning or maintaining the appliance. Do not unplug the power adapter by pulling on the power cord.
- Do not attempt to service the adapter. There are no service parts inside. Replace the whole unit if it is damaged or exposed to high moisture. Consult your Mamibot dealer for help and maintenance.
- The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, have short contact, heat above 60 °C (140 °F), or incinerate.
- If you have to dispose of this old equipment, please take it to the local recycling center for recycling electrical and electronic parts. Retain the safety and operating instructions for future reference.
- Follow all operating and use instructions.
- Do not expose your device to rain or excess humidity, and keep it away from liquids (such as beverages, faucets, and so on).
- Avoid exposing your device to direct sunlight or intense light source, and keep it away from heat sources (such as radiators, space heaters, stoves, and so on).
- Do not place the device in the vicinity of strong magnetic fields.
- Keep the device and accessories away from children.
- Product operating temperature: 0 °C ~ 40 °C (32 °F ~ 104 °F).
- Don’t use it on cracked glass or to clean another surface with uneven areas as it may fall off due to insufficient suction power.
- The backup battery must be replaced by the manufacturer or its service agent in order to avoid a hazard. The backup battery must be removed and discarded according to local laws and regulations before disposal of the appliance. Please dispose of used batteries according to local laws and regulations.
- The appliance must be disconnected from the receptacle before removing the battery for disposal of the appliance.
- The appliance must be used in accordance with the directions in this instruction manual. Product manufacturers cannot be held liable or responsible for any damages or injuries caused by improper use.
Risk of Electric Shock!
- Always switch the device off before carrying out any cleaning or maintenance work.
- Never pull the power plug out of the socket by the power cord; instead, pull it out by the power plug itself.
- Never perform repairs on your device yourself. Repairs to electric devices may only be carried out by an authorized customer service center.
- Do not insert any pointed objects into the electric contacts.
- Do not change the contacts.
- Do not continue to operate the robot if the device itself or the power cord is damaged.
- Contact your local customer service in the event of damage.
- Do not clean the robot, the power cable in water or other liquids.
- Do not use the robot on damp ground or in places in which it can get into contact with liquids or be immersed in water.
- Do not use the robot in hazardous areas such as open fireplaces, running showers or swimming pools. il
- Make sure that you do not damage, bend or twist the power cord. Do not place any heavy objects on top of the cord. This could damage the power cord and cause a fire or electrical shock
Warning
- Fasten the safety rope and tie it to the indoor fixture before operating the device.
- Check if the safety rope is broken or the knot is loose before operating the device.
- Set danger-warning area downstairs for no-balcony window and door.
- The battery shall be full-charged (Orange lamp ON) before use.
- Do not use it on rainy or moist days.
- Turn the power on before you put the device onto the glass.
- Make sure the device can stick and stand on the glass surface while put onto the glass.
- Before turn the power off, please hold the device.
- Do not use it on frameless glass.
- Make sure to put the cleaning pad on the bottom of the device correctly for no leakage.
- Do not spray or pour water onto the device.
- Prohibit children from using this device.
- Remove everything on the glass. Do not use cracked glass. Reflective or coating glass might be slightly scratched due to dirt on the glass while operating.
- Keep hair, loose clothing, fingers, and all parts of the body away from the openings and moving parts.
- Do not use in areas with existed flammable or combustible liquids, gas.
Scan QR Code for APP downloading from here
iOS System:
Requires iOS 7.0 or later. Compatible with iPhone iPad, and iPod touch.
https://itunes.apple.com/us/app/iglassbot/id1297871093?mt=8
Android System:
Requires Android 4.3 or later, Bluetooth 4.0 or later.
https://play.google.com/store/apps/details?id=com.timyerc.iglassbot
Notes:
Make sure the W120-T is switched on before connecting; If it is not connected
successful, turn off the APP from the device background, try again later.
Product Description & Parameters
Product Diagram
Product Parameters
About The Robot
Model No.| W120-T| Rated Voltage| 24 V DC
Rated Power| 75 W| Noise Level| About 65 dB
Battery Capacity| 600 mAh| Charging Time| About 1 h
Dimension| 25 x 25 x 10 cm| Net Weight| 1.35 kgs
Cleaning Speed| About 2.5 min / m²| |
Adapter
Input| AC 100-240 V
50 / 60Hz 2.0 A| Output| 24 V / 3.75 A
What‘s in the Package?
Remote Control
Z| Automatically “Z”
Type Cleaning| | Manual Move UP
---|---|---|---
N| Automatically “N”
Type Cleaning| | Manual Move Down
Z|N| From “Z” to “N” Cleaning| | Manual Move Right
A| No Use Yet| | Manual Move Left
B| No Use Yet| | Start Cleaning
Choose “Z” or “N” type automatically
STOP| Stop Cleaning| | Stop / Restart
It is 2.4 G wireless remote control, which can control your robot within maximum 15 meters away from any direction.
Installation
Assemble the Adapter
A. Connect DC plug (End A) of Power Adapter with extension cable (End B),
as above. 1
B. Connect End C to the robot power socket, screw the connector until
it’s tightly locked. 2
Fix the Safety Rope
A. Plug in the safety lock into the lock hole, turn the safety lock
clockwise around the lock hole till the indicator turns green. 3
Note: W120-T can only be used when the indicator is in green.
B. Tie the other end of the rope to the indoor fixture securely. 0
Attach Cleaning Pad
A. Choose the proper cleaning pad for your window.
B. Attach the cleaning pad to the
W120-T bottom properly, the pad should not cover driving treads or edge
sensors. 5
C. Spray 5 times of cleaning solution to the upper and lower side of
W120-T, 6 wipe the bottom after spraying.
Connect to Power Supply
Plugin W120-T. 8
Important Notes:
Be sure your W120-T is always connected to the AC power supply while working.
Don’t use it if the backup battery is lacking power, use it after full
charging. Take off your W120-T asap, if the power supply is cut or unplugged
accidently.
Operate W120-T
On/Off Button A. Power On/Off button – Press for 2 seconds to turn
on/off your W120-T.
B. Press the On/Off button once to start or stop the W120-T when it is
placed on the window.
Start Your W120-T
A. Press the On/Off button for 2 seconds to turn on your W120.
B. Place your W120-T on glass, press again the On/Off button to start.
C. You can also start it from your remote control “START” button.
Caution: Before starting, make sure the edge of W120-T is 8 cm or more
away from window frames or corners.
Stop/Pause
A. When W120-T is cleaning, press the On/Off button on the device or the
Stop button on the remote control to stop it.
B. When W120-T is cleaning, press the Pause button on the remote control
to pause/restart it.
C. You can also start it from your remote control Start button.
Use of Remote Control
Z| Automatically “Z”
Type Cleaning| | Manual Move UP
---|---|---|---
N| Automatically “N”
Type Cleaning| | Manual Move Down
Z|N| From “Z” to “N” Cleaning| | Manual Move Right
A| No Use Yet| | Manual Move Left
B| No Use Yet| | Start Cleaning
Choose “Z” or “N” type automatically
STOP| Stop Cleaning| | Stop / Restart
Operate W120-T
Take off W120-T after cleaning
W120 will return to its starting point automatically after cleaning is finished. There is a beep warning when cleaning is completed.
A. Use the remote control to move your W120-T to a reachable location;
B. Press the On/Off Button for 2 seconds to switch it off;
C. Grasp the handle and take it off from the window;
D. Untie the safety rope after finishing cleaning. Put the device and its
spare parts in dry condition for future use.
Use APP on Your Smartphone
A. Download App for your iOS/Android device (refer to page 2 to scan and
download, or search for
“iGlassbot” in your Appstore or googleplay).
B. Turn on BLUETOOTH on your cell phone and open the iGLASSBOT APP on
your phone.
C. Click the BLUETOOTH ICON on your iGLASSBOT interface to search the
device and connect your W120-T with your phone, you can control it through
your cellphone now.
Maintenance
Cleaning Pad Maintenance
Put your W120-T up-side-down, take off the cleaning pad and put it into cold
water, wash the cleaning pad with detergent and dry it for reuse.
Note: wet cleaning pad is not suggested to be used as it may get your
robot stuck when cleaning glass with heavy dirt.
Fan Maintenance
Put your W120-T upside-down, use a clean and dry cloth to wipe out
dirt/debris on the fan.
Edge Sensors Maintenance
Put your W120-T upside-down, use a clean and dry cloth to wipe out
dirt/debris of the sensors.
Driving Treads Maintenance
Put your W120-T upside-down, use a clean and dry cloth to wipe out dirt/debris
on it.
Troubleshooting
Malfunction
| Possible Causes|
Solutions
---|---|---
The device gets slippery or works in irregular patterns.| A. Glass is too
dirty or too wet.
B. Cleaning pad is too dirty or too wet.| A.Change cleaning pad.
B. Clean the driving treads.
C. Use the remote control to manually restart it.
power.| power.| A. Check if the cleaning pad is attached properly, replace it
correctly.
B. Check if there is any crack on the glass.
C. Check if the glass frames are with uneven area/ rubber part. If there is
an uneven area or uneven rubber part on the glass, use remote control to
operate the device manually and keep the W120-T away from the uneven area /
uneven rubber part when cleaning.
The devices can’t be started after being switched on or works in irregular
patterns.| Edge detection sensor abnormal.| A. Remove the cleaning pad and
reattach it making sure it is placed exactly within its velcro area and does
not cover the edge detection sensors.
B. Open APP on your phone, connect it with the corners of APP interface (Red
indications on the APP interface means the edge sensor malfunctions).
C. Edge detection sensors failure, contact after-sales service.
Red indicator light
once/second| Improper connection of Power Supply.| Check if the plug is
connected well, or the screws of the extension cables are placed tight.
Both Red and Blue
| Hardware failure.| Contact after-sales service.
The remote control does not work.| A. No battery inside or the battery has
low power.
B. Remote control is broken.| A. Change the battery.
B. Replace the remote control with a new one.
The device got stuck on glass frames.| Edge-detection misjudged- gement.| A.
Press STOP on the remote control, move the device
B. Pull the robot lightly to a reachable location if you can’t remote control
it.
Both Red and Blue Light are on, no beeps.| The device is not sucking properly
on the window.| Put the device on the window surface manually, make sure it
sucks on the window properly.
Buzzer beeps twice when it’s in use.| Edge sensor detects frameless glass.|
It’s normal if it is cleaning frameless glass.
Squeaky sound when it’s in use.| Glass is too dry or edge detection sensors
are too dirty.| A. Spray a little bit of water on the cleaning cloth.
B. Clean the edge detection sensors and operate again.
The device doesn’t return to Starting Point after cleaning.| The glass
surface’s friction index is different.| Use the remote control to direct the
device to return to the reachable location.
Disclaimer
The manufacturer makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation of this company to notify any person of such revision or changes.
The place and safety of this glass cleaning tool usage must be judged and responsible by the user. But also need to follow the instructions in this user manual.
Product Warranty
If there are defects in your W120-T glass-cleaning robot due to faulty materials, workmanship or function within the warranty period from the date of purchase or delivery, please contact your local retailers or local authorized dealers for repair or replacement.
Exclusions
This warranty will automatically become null and void and shall not be applicable to any purchased products if:
- Normal wear and tear (e.g. cleaning cloth, safety rope, etc).
- Reduction in battery discharge time due to battery age or use.
- Damage caused by assembling or installing that not in accordance with the instructions of the manufacturer.
- Damage caused by using the glass-cleaning robot for any other purposes than normal domestic household.
- Damage caused by using parts and accessories which are not specified by the manufacturer.
- Damage caused by accident, abuse, or misuse.
The Environment
The symbol on this appliance indicates that this appliance may not be treated as household waste. Instead, it must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about the treatment, recovery, and recycling of this appliance, please contact your local city office, your household, and waste disposal service, or the shop where you purchased the appliance.
This appliance complies with the European Directives 2014/30/EU, 2014/35/EU,
and 2014/53/EU.
Subject to change without notice.
Mamibot Manufacturing USA Inc.
Orange Street #600, New Castle, Wilmington, Delaware, USA 19899
www.mamibot.com,
sales@mamibot.com, 001 302 428 9888
Manufacturer: Mamibot Manufacturing (Shanghai) Co.Ltd
North 21th, No.1 Building, LN1040 Caoyang Rd, Shanghai, P.R.C.