NINJA JC101 Cold Press Juicer User Guide

: June 6, 2024
: Ninja

Table of Contents

NINJA JC101 Cold Press Juicer
What’s in the Box
Assembly
Disassembly
Cleaning
Using the Juicer
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NINJA JC101 Cold Press Juicer

What’s in the Box

A Main Body
B Tamper
C Food Tray
D Feed Chute Chamber
E Juice Jug
F Auger
G Black Filter (no pulp)
H Gray Filter (some pulp)
(not available with all models)
I Orange Filter (lots of pulp)
J Pulp Spout
K Pulp Container
L Cleaning Brush

Using the Filters for Pulp Control
Control the amount of pulp by choosing the desired filter.

Use the black filter with the finest mesh for juice with no pulp. using the
filter Use the gray filter* with the larger mesh for juice with some pulp.
Not available with all models using the filter 1 Use the orange filter with the largest mesh for juice with lots of pulp.

using the filter 2

Using the Control Panel

START/STOP
Press once to start continuous running up to 12 minutes; press again to stop.

Using the Control Panel

REVERSE
If the feed chute chamber becomes blocked or ingredients are not processing, press and hold REVERSE. There will be a beep and a brief pause, then the auger will rotate in the opposite direction. Release REVERSE to stop. Repeat as needed. Press START/STOP to resume normal operation.

Assembly

assembly 1

Insert the auger in the feed chute chamber, then attach the desired filter onto the auger.
Attach the pulp spout to the feed chute chamber by installing at an angle on top of the filter, then turn counter clockwise to lock in place.
Install the assembled feed chute chamber on the motor base at an angle, then turn counterclockwise until it clicks into place.
Install the food tray on the top of the feed chute, then install the tamper.
Place the juice jug under the anti-drip lever on the feed chute chamber.
Place the pulp container under the pulp spout.

Disassembly

Press and HOLD the RELEASE button while turning the feed chute chamber clockwise and remove from motor base.
Remove the pulp spout from the feed chute chamber by turning clockwise.
Then, remove the filter and auger.

disassembly

Cleaning

IMPORTANT: DO NOT add water to the feed chute while the unit is operating to clean the unit.

Use the end of the cleaning brush to clear any buildup left over after juicing.

Using the Cleaning Brush

Use the bristle side of the cleaning brush to clean the filter, if needed.

Using the Cleaning Brush 1

Dishwasher
All parts, except the motor base, are dishwasher safe.

Hand-Washing
Wash parts in warm, soapy water.
Use the included cleaning brush for hard-to-clean areas, such as the filter.

For questions or to register your product, visit us online at ninjakitchen.com

@ninjakitchen
© 2020 SharkNinja Operating LLC.
NINJA is a registered trademarks of SharkNinja Operating LLC.
JC100Series_QSG_MP_Mv10

Using the Juicer

Make sure the anti-drip lever is open before juicing.
Press START/STOP, then gradually add ingredients to the feed chute. For best results, allow juicer to process each ingredient before adding more. Use the tamper to push ingredients down into feed chute as needed. When done, press START/STOP to stop the unit.
Close the anti-drip lever so juice won’t drip onto the motor base. Remove juice jug from unit, stir juice, and serve.

Using the Juicer

Juicing 101
Use the freshest and ripest fruits and vegetables, and wash them prior to juicing.
Always turn on the juicer before adding ingredients to the feed chute.
Add ingredients gradually, making sure all of them have been processed/moved through the feed chute chamber before adding more.

Juicing 101 Juicing 101 1