makita GA4034 Cordless Angle Grinder Instruction Manual
- June 3, 2024
- Makita
Table of Contents
(Original instructions)
INSTRUCTION MANUAL
Angle Grinder
GA4034
GA4534 GA5034
DOUBLE INSULATION
0106891
IMPORTANT: Read Before Using.
(Original instructions)
SPECIFICATIONS
| Model | GA4034 | GA4534 | GA5034 |
|---|---|---|---|
| Depressed center wheel diameter | 100 mm | 115 mm | 125 mm |
| Max. wheel thickness | 6.4 mm | 6.4 mm | 6.4 mm |
| Spindle thread | M10 | M14 or 5/8″ | |
| (country specific) | M14 or 5/8″ |
(country specific)
Rated speed (n)/No load speed (no)| 11,000 min”‘| 11,000 min”‘| 11,000 min”‘
Overall length| 265 mm| 265 mm| 265 mm
Net weight| 1.8 kg| 1.9 kg| 1.9 kg
Safety class| I/II
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
- Read instruction manual.
- DOUBLE INSULATION
- Wear safety glasses.
- Only for EU countries
Do not dispose of electric equipment together with household waste material!
In observance of European Directive 2012/19/EU on waste electric and
electronic equipment and its implementation in accordance with national law,
electric equipment that
have reached the end of their life must be collected separately and returned
toan environmentally compatible recycling facility.ENF002-2
Intended use
The tool is intended for grinding, sanding and cutting of metal and stone
materials without the use of water.
Power supply
The tool should be connected only to a power supply of the same voltage as
indicated on the nameplate, and can only be operated on single-phase AC
supply. They are double-insulated and can, therefore, also be used rom sockets
without earth wire.ENG905-1
Noise
The typical A-weighted noise level determined according to EN60745:
Sound pressure level (LpA) : 86 dB(A)
Sound power level (LWA) : 97 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum) determined according to
EN60745:
Model GA4034
Work mode : surface grinding
Vibration emission (ah,AG) : 7.5 m/s 2 Uncertainty (K) : 1.5 m/s 2
Work mode: disc sanding
Vibration emission (ah,DS) : 2.5 m/s 2 or less
Uncertainty (K) : 1.5 m/s 2
Model GA4534
Work mode : surface grinding
Vibration emission (ah,AG) : 8.0 m/s 2
Uncertainty (K) : 1.5 m/s 2
Work mode : disc sanding
Vibration emission (ah,DS) : 2.5 m/s 2
Uncertainty (K) : 1.5 m/s 2
Model GA5034
Work mode : surface grinding
Vibration emission (ah,AG) : 8.0 m/s 2
Uncertainty (K) : 1.5 m/s 2
Work mode: disc sanding
Vibration emission (ah,DS) : 2.5 m/s 2 or less
Uncertainty (K) : 1.5 m/s 2 ENG902-1
- The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
- The declared vibration emission value may also be used in a preliminary assessment of exposure.
- The declared vibration emission value is used for main applications of the power tool. However if the power tool is used for other applications, the vibration emission value may be different.
WARNING:
- The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.
- Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible manufacturer declare that the
following Makita machine(s):
Designation of Machine: Angle Grinder
Model No./ Type: GA4034,GA4534,GA5034
are of series production and Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following standards or
standardised documents: EN60745
The technical documentation is kept by: Makita International Europe Ltd.
Technical Department, Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD,
England
26.6.2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
Work area safety
-
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
-
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
-
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety -
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
-
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
-
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
-
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
-
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
-
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
-
Use of power supply via a RCD with a rated residual current of 30mA or less is always recommended.Personal safety
-
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
-
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
-
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
-
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
-
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
-
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust- related hazards. Power tool use and care
-
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
-
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
-
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
-
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
-
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
-
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
-
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Service
-
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
-
Follow instruction for lubricating and changing accessories.
-
Keep handles dry, clean and free from oil and grease. GEB033-7
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire Brushing, or Abrasive Cutting-Off Operations:
-
This power tool is intended to function as a grinder, sander, wire brush or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
-
Operations such as polishing are not recommended to be performed with this power tool. Operations for which the power toolwas not designed may create a hazard and cause personal injury.
-
Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it
does not assure safe operation. -
The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
-
The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
-
Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
-
Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
-
Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.
-
Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
-
Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
-
Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.
-
Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.
-
Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
-
Do not operate the power tool near flammable materials. Sparks could ignite these materials.
-
Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding. For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions. Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory. Accessory may kickback over your hand.
c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.
Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations:
a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.
b) The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
c) The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing.
d) Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
f) Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.
Additional Safety Warnings Specific for Abrasive Cutting-Off Operations:
a) Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
f) Use extra caution when making a “pocket cut” into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.
Safety Warnings Specific for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin. b) If the use of a guard is recommended for wire brushing, do not allow interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces. Additional Safety Warnings: -
When using depressed centre grinding wheels, be sure to use only fiberglassreinforced wheels.
-
NEVER USE Stone Cup type wheels with this grinder. This grinder is not designed for these types of wheels and the use of such a product may result in serious personal injury.
-
Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage.
-
Make sure the wheel is not contacting the workpiece before the switch is turned on.
-
Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel.
-
Use the specified surface of the wheel to perform the grinding.
-
Do not leave the tool running. Operate the tool only when hand-held.
-
Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin.
-
Observe the instructions of the manufacturer for correct mounting and use of wheels. Handle and store wheels with care.
-
Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels.
-
Use only flanges specified for this tool.
-
For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length.
-
Check that the workpiece is properly supported.
-
Pay attention that the wheel continues to rotate after the tool is switched off.
-
If working place is extremely hot and humid, or badly polluted by conductive dust, use a short-circuit breaker (30 mA) to assure operator safety.
-
Do not use the tool on any materials containing asbestos.
-
When use cut-off wheel, always work with the dust collecting wheel guard required by domestic regulation.
-
Cutting discs must not be subjected to any lateral pressure.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to safety rules for the subject
product. MISUSE or
failure to follow the safety rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
-
Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Shaft lock
CAUTION: -
Never actuate the shaft lock when the spindle is moving. The tool may be damaged.
Press the shaft lock to prevent spindle rotation when installing or removing
accessories. Switch action
CAUTION:
- Before plugging in the tool, always check to see that the switch lever actuates properly and returns to the “OFF” position when released.
To prevent the switch lever from being accidentally pulled, a lock-off lever is provided. To start the tool, pull the lock-off lever toward the operator and then pull the switch lever. Release the switch lever to stop.
ASSEMBLY
CAUTION:
-
Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.
Installing side grip (handle)
CAUTION: -
Always be sure that the side grip is installed securely before operation.
Screw the side grip securely on the position of the tool as shown in the
figure.
Installing or removing wheel guard (For depressed center wheel , multi disc /
abrasive cut-off wheel , diamond wheel)
WARNING:
-
When using a depressed center grinding wheel/Multi-disc, flex wheel, wire wheel brush, cutoff wheel or diamond wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
-
When using an abrasive cut-off / diamond wheel, be sure to use only the special wheel guarddesigned for use with cut-off wheels. (In Europeancountries, when using a diamond wheel, theordinary guard can be used.)
CAUTION: -
Use a wheel guard with a specific shape according to the application. For tool with locking screw type wheel guard
Mount the wheel guard with the protrusion on the wheel guard band aligned with
the notch on the bearing box. Then rotate the wheel guard to such an angle
that it can
protect the operator according to work. Be sure to tighten the screw securely.
To remove wheel guard, follow the installation procedure in reverse.
For tool with clamp lever type wheel guard
Loosen the lever on the wheel guard after loosening the screw. Mount the wheel
guard with the protrusion on the wheel guard band aligned with the notch on
the bearing box. Then rotate the wheel guard around to the position shown in
the figure. Tighten the lever to fasten the wheel guard. If the lever is too
tight or too loose to fasten the wheel guard, loosen or tighten the screw to
adjust the tightening of the wheel guard band. To remove wheel guard, follow
the installation procedure in reverse.
Installing or removing depressed center grinding wheel/Multi-disc
WARNING:
- Always use supplied guard when depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury.
- Lock nut
- Depressed center grindingwheel/Multi-disc
- Inner flange
Mount the inner flange onto the spindle. Fit the wheel/disc on the inner
flange and screw the lock nut onto the spindle.
In case of mounting a wheel/disc thinner than 3mm, place the lock nut so that
the protrusion on the lock nut faces outside. Otherwise place it so that the
protrusion on it fits into the inner diameter of the wheel/disc.
To tighten the lock nut, press the shaft lock firmly so that the spindle
cannot revolve, then use the lock nut wrench and securely tighten clockwise.
- Lock nut wrench
- Shaft lock
To remove the wheel, follow the installation procedure in reverse.
WARNING: Only actuate the shaft lock when the spindle is not moving.
OPERATION
WARNING:
-
It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage.
-
ALWAYS replace wheel if tool is dropped while grinding.
-
NEVER bang or hit grinding disc or wheel onto work.
-
Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc.
This can cause loss of control and kickback. -
NEVER use tool with wood cutting blades and other saw blades. Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury.
CAUTION: -
After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down.
Grinding and sanding operation
ALWAYS hold the tool firmly with one hand on housing and the other on the side
handle. Turn the tool on and then apply the wheel or disc to the workpiece.
In general, keep the edge of the wheel or disc at an angle of about 15 degrees
to the workpiece surface. During the break-in period with a new wheel, do not
work the grinder in the B direction or it will cut into the workpiece. Once
the edge of the wheel has been rounded off by use, the wheel may be worked in
both A and B direction.
Operation with abrasive cut-off / diamond wheel (optional
accessory)
- Lock nut
- Abrasive cut-off wheel/diamond wheel
- Inner flange
- Wheel guard for abrasive cut-off wheel/diamond wheel
The direction for mounting the lock nut and the inner flange varies by wheel
thickness. Refer to the table below. 
WARNING:
- When using an abrasive cut-off / diamond wheel, be sure to use only the special wheel guarddesigned for use with cut-off wheels. (In Europeancountries, when using a diamond wheel, theordinary guard can be used.)
- NEVER use cut-off wheel for side grinding.
- Do not “jam” the wheel or apply excessivepressure. Do not attempt to make an excessivedepth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback, wheel breakage and overheating of the motor may occur.
- Do not start the cutting operation in the workpiece. Let the wheel reach full speed and carefully enter into the cut moving the tool forward over theworkpiece surface. The wheel may bind, walk upor kickback if the power tool is started in the workpiece.
- During cutting operations, never change the angle of the wheel. Placing side pressure on the cut-off wheel (as in grinding) will cause the wheel to crack and break, causing serious personal injury.
- A diamond wheel shall be operated perpendicularto the material being cut.
MAINTENANCE
CAUTION:
- Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
- Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
The tool and its air vents have to be kept clean.
Regularly clean the tool’s air vents or whenever the vents start to become
obstructed.
To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection
and replacement, any other maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
-
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. -
Wheel guard (Wheel cover) For depressed center wheel / Multi disc
-
Wheel guard (Wheel cover) For abrasive cut-off wheel / diamond wheel
-
Depressed center wheels
-
Abrasive cut-off wheel
-
Multi discs
-
Diamond wheels
-
Wire cup brushes
-
Wire bevel brush 85
-
Abrasive discs
-
Inner flange
-
Lock nut (For depressed center wheel / abrasive cut-off wheel / multi disc / diamond wheel)
-
Lock nut (For abrasive disc)
-
Lock nut wrench
-
Side grip
NOTE: -
Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
https://tm.by
Makita Corporation Anjo, Aichi, Japan
www.makita.com
884935C227
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>