Harman HSA-20UT-AA SmartAuto TAG2.0 User Guide
- June 6, 2024
- Harman
Table of Contents
Harman
SmartAuto TAG2.0
Quick Start Guide
Issue 1.0
About SmartAuto TAG2.0
SmartAuto TAG2.0 is an intelligent OBD solution, which integrates 4G modules,
GPS, acceleration sensor, and ECU communication module. Developed on Qualcomm
chipset aST MCU, it can provide vehicle position, collect statistics on
vehicle trajectory, reconstruct driving behavior, collect station fuel
consumption, track the vehicle to prevent theft, read vehicle status,
read/clear vehicle fault codes, etc. This OBD solution is well applicable to
individual consumers, ßeet management, UBI, vehicle rental, and vehicle
maintenance
1.1 Product Functions
- LTE communications
- Real-time vehicle data
- Vehicle DTC code
- GPS/GLONASS/BS/A-GPS positioning
- Supplementary transmission for
- Blind-area data
- Swapping alarming
- FOTA upgrade
- Sleeping and awaking
- Driving behavior analysis
1.2 Package Content
| Part | Unit | Quantity |
|---|---|---|
| TAG2.0 OLD | pcs | 1 |
| Quick start guide | pcs | 1 |
Product Features
| Features | Description |
|---|---|
| Developed network standards compliant | Developed on Qualcomm chipset able to |
operate on networks of multiple countries
Wide operating voltage range| 12V/24V DC power supply, applicable to different
vehicle models
Driving behavior analysis| Built-in acceleration sensor and gyroscope to
collect the information
about driving behaviors
Complete & stable Applications|
Wide operating voltage range| 12V/24V DC power supply, applicable to different
vehicle models
Driving behavior analysis| Built-in acceleration sensor and gyroscope to
collect the information about driving behaviors
Complete & stable Applications| Device management, position fix, vehicle
diagnosis, driving behavior analysis, and other applications
Various OBD-II Protocols| • ISO 9141-2, ISO14230-4, ISO15765-4,
• SAE J1850 VPW (GM vehicles)
• SAE J1850 PWM (Ford vehicle)
• SAE J1939
Operational range temperature, C° ( full function )| Charge :10 ～45℃ ，Relative
humidity≤75%
Discharge： -20 ～ +55℃ ，Relative
humidity≤75%
Storage| Storage for 30 days: – 20 ℃～ + 50 ℃
How to Install and Start
3.1 Install
When the vehicle is shut down, insert the device into the OBDII interface.
This interface is usually located under the dashboard of the vehicle and above
the accelerator pedal. If not, refer to the schematic or your owner’s manual.
If the installation affects driving, you can purchase the extension
cable and place it in a safe place.
3.2 F first
use
For the first use, initialization is required: after inserting the equipment,
start the engine and keep idling for 3-5 minutes until the equipment works
normally (the red and green status indicator lights are always on). Your
device is ready for normal use!
3.3 LED Indicator
Status
| Colour|
describe
---|---|---
GPS| Blue| a. GPS disable, the LED will be off
b. GPS “ON ” but location not fixed, the LED will be Blue Blinking.
c. GPS “ON ” and location fixed, the LED will be Blue Solid
Wi-Fi| Blue| a. WiFi “OFF “, the LED will be off
b. WiFi “ON “, the LED will be Blue Blinking
c. WiFi client connection will be solid blue
LTE| Green/Red /Blue| a. Modem Off and in Sleep mode, the LED will be off
b. Network connection in progress LED Blinking Red
c. Network connection successful LED solid green
3.4 Platform Operation
Set the dialup profile, server IP address, and port through an SMS message to
log in to the server. Then you can query and set the device parameters.
Safety Warning
4 Safety Warning
Please use a battery specified by the device manufacturer.
Otherwise, all warranty services are invalid.
The device manufacturer will not provide a warranty for damage caused by non-
OEM accessories.
- Do NOT put the device into water or f ire.
- Do NOT bend or open the battery.
- Do NOT recharge the battery.
- Do NOT disassemble the device. Improper handling might damage the device permanently.
FCC
5.1 Regulatory Requirement
Harman SmartAuto TAG2.0 device complies with Part 15 of FCC
Rules. Operation is subject to the following two conditions: (1) The device
may not cause harmful interference, and (2) The device must accept any
interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
5.2 Body-support SAR
This equipment should be installed and operated with a minimum distance of 10
mm between the device and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>