HomeSpot HS3-NS001-RB-V2 Bluetooth Audio Transmitter Adapter for Nintendo Switch User Guide
- June 6, 2024
- HomeSpot
Table of Contents
- Package Contents
- About your HomeSpot HS3 NS002
- Setting up your hardware
- Connecting to one Bluetooth headphones
- Connecting to two Bluetooth headphones
- Reconnecting to a previously paired headphones
- In-game Voice Chat
- Factory Reset
- TV Mode
- LED Indicators
- Product Specifications
- Safety Instructions
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HomeSpot HS3-NS001-RB-V2 Bluetooth Audio Transmitter Adapter for Nintendo
Switch User Guide
Package Contents
-
HomeSpot HS3 NS002
-
User Guide
-
USB-C to USB-A Adapter
-
Pouch
-
Warranty Card
About your HomeSpot HS3 NS002
Setting up your hardware
- Turn on the NSwitch and go to the Home menu.
- Insert the HomeSpot HS3 NS002 into the NSwitch USB-C port.
- LED indictors on the HomeSpot HS3 NS002 will start flashing.
- HomeSpot HS3 NS002 is ready for pairing and connecting with your headphones once the LEDs have stop flashing.
- For in-game voice chat, after headphones is paired and connected, press the
P1/P2 button to toggle the Internal Mic On/Off. When the Internal Mic is Off,
P1/P2 LED is Green. When the Internal Mic is On, P1/P2 LED is Amber.
Connecting to one Bluetooth headphones
- Upon powering up, HomeSpot HS3 NS002 automatically enters pairing mode on first use.
- Make sure the Bluetooth headphones is in pairing mode.
- Keep the headphones close to the HS3 NS002 during initial pairing.
- Once connected, P1/P2 LED will be Green and headphones will start receiving audio from the NSwitch.
Connecting to two Bluetooth headphones
- Pair and connect to the first headphones, P1 LED will be Green.
- Pair the 2nd headphones by pressing the P2 button for 3 seconds.
- Keep the 2nd headphones close to the HS3 NS002 during initial pairing.
- Once both headphones are connected, both P1 and P2 LEDs will be Green.
- Both headphones will start receiving audio from the NSwitch.
Reconnecting to a previously paired headphones
-
Automatic re-connect
When a previously paired headphones is turned on, it will automatically re- connect to the HomeSpot HS3 NS002. -
Manual re-connect
You may also manually initiate a re-connect by pressing either the P1 or P2 button, the corresponding previously paired 1st or 2nd headphones will be re- connected respectively.
In-game Voice Chat
- Make sure one or both headphones are paired and connected to the HomeSpot HS3 NS002.
- Press the P1/P2 button to toggle the Internal Mic On/Off. When Internal Mic is Off, P1/P2 LED is Green. When Internal Mic is On, P1/P2 LED is Amber.
Factory Reset
- Power on the Nintendo Switch and go to the Home menu.
- Insert the Bluetooth adapter into the bottom USB-C port on the Switch.
- Press and hold both P1 and P2 buttons for 5 seconds until all LEDs start flashing.
TV Mode
The HomeSpot HS3 NS002 can also be used with the TV dock. Simply plug the bundled USB-C to USB-A adapter to the USB-A port on the side of the TV dock, then insert the HS3 NS002 into USB-C port on the adapter.
Follow the previous pairing procedures for headphones connection.
LED Indicators
- LED Off
- Colored-line box – LED On
- Dashed box – LED flashing
Product Specifications
Bluetooth version | Bluetooth 5.0 |
---|---|
Operating Frequency | 2402 – 2408MHz |
Supported Bluetooth Profiles | AD2P, HFP |
Supported Codecs | aptX Low Latency, aptX, SBC |
Operating Range | Up to 10 meters line of sight |
Operating Temperature Range | 0˚C to 45˚C |
Safety Instructions
- Do not use this device in medical facilities, aircraft, refueling points, close to automatic doors, automatic fire alarms or other remotely controlled devices.
- Keep this device at least 20 cm from pacemakers and other medical devices as Bluetooth signal may interfere with their operation.