NETIO PowerBox 3PE Professional Power Strip with Open API Installation Guide

NETIO PowerBox 3PE Professional Power Strip with Open API

Quick Installation Guide (QIG)

Thank you for purchasing a product of NETIO products a.s. Before using your product for the first time, please read this short guide to avoid problems with incorrect installation or use. For more information, please see the User’s Manual available at http://netio-products.com.

Please read carefully the following notice.
The NETIO PowerBOX 3Px is an electrical device. Mishandling may damage the device, void your warranty, or result in injury or death.

Safety Notices

1. The manufacturer is not liable for any damage caused by incorrect use of the device or by operating it in an unsuitable environment.
2. The device is not rated for outdoor use. 3) Do not expose the device to strong vibrations.
3. Unauthorized modifications may damage the device or cause a fire.
4. Protect the device from liquids and excessive temperatures.
5. Make sure the device does not fall.
6. Only electrical appliances approved for use with the electrical network may be connected to the device.
7. Do not connect multiple devices in series.
8. The cable plug must be easily accessible.
9. The device is completely switched off only when unplugged.
10. If the device malfunctions, disconnect it from the electrical outlet and contact your vendor.
11. Do not cover the device.
12. Do not use the device if it appears to be mechanically damaged.
13. Make sure that the input and output cables are rated for the respective current.

Minimum system requirements

A device with an Internet browser (Firefox, Opera, Mozilla, Chrome etc.) that has JavaScript and Cookies support enabled.

Package contents

• NETIO PowerBOX 3Px device
• Quick Installation Guide (QIG)

Status / control indication

1. 1x RJ45 LAN connector
2. RJ45 LEDs ­ device states (yellow and green)
3. Multifunction “SETUP” button

LED and button functions

OUTPUT LEDs

system restarts

SETUP button

Switching all outputs| Output test:

Press the SETUP button 3x rapidly.

– If any of output is On (1) -> Off (0).
– If all outputs are Off (0), All outputs -> On (1).
When powering on the device, hold the “SETUP” button pressed for about 10 seconds, until the yellow LED on the RJ45 jack flashes 3 times.

---|---
Restoring factory defaults

Before the first use

1. Connect your NETIO device to a LAN with a network cable (RJ45).
2. Connect the NETIO device to a mains electrical outlet with the power cable.
3. Wait about 1 minute until the device starts and receive IP address from DHCP server.

NETIO Discover

1. Find the NETIO Discover (MS Windows) utility at our website and install it.

2. NETIO Discover finds all NETIO devices on the network and displays them.
   Click on the IP address to open the web interface.

3. The displayed MAC address can be checked with the label on the device.
   

Note:
A DHCP server is required for the first installation. Fixed IP address, mask and GW can be defined via the device web.

WEB interface

The default username / password combination is admin/admin.

Specifications

Power| 90-240 V; 50/60 Hz; 16 A – PowerBOX 3PE
90-240 V; 50/60 Hz; 16 A – PowerBOX 3PF
90-240 V; 50/60 Hz; 13 A – PowerBOX 3PG
---|---
Switched outputs| 16 A in total / 16 A each output – PowerBOX 3PE
16 A in total / 16 A each output – PowerBOX 3PF
13 A in total / 13 A each output – PowerBOX 3PG
Fuse| Integrated, non-resettable

Max 2 W

Micro-disconnection (µ) (resistive load), SPST 1E5 switching cycles, max. 1.5 kV pulse voltage Switch heat and fire resistance class 1

1x Ethernet RJ-45 10/100 Mbit/

Internal consumption
Output relay
Interfaces
Environment| IP30, protection rating = class 1
Operating temperature -20°C to +75°C
Device rated for pollution degree 2.
Permanent use in altitudes up to 2000 MASL (metres above sea level).
Does not require additional cooling

DECLARATION OF CONFORMITY

NETIO PowerBOX 3PF
NETIO PowerBOX 3PG

RTTED:
The product mentioned above to which this declaration relates is in conformity with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC).

LVD:
The product mentioned above to which this declaration relates is in conformity with the essential requirements and other relevant requirements of the Directive 2006/95/EC.
The product mentioned above is in conformity with the following standards and/or other normative documents:
EN 60950-1
EN 62368

RoHS:
The product mentioned above to which this declaration relates is in conformity with the essential requirements and other relevant requirements of the Directive 2011/65/EU (restriction of the use of certain hazardous substances in electrical and electronic equipment).
The product mentioned above is in conformity with the following standards and/or other normative documents: EN 50581: 2012

Czech Republic, Prague, February 26th, 2020

Jan ehák, Chair of the board

www.netio- products.com

References

• NETIO products a.s. | Professional smart power sockets, strips and PDUs
• NETIO products a.s. | Professional smart power sockets, strips and PDUs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>